STD-ASTM D XXXX Conti 4

ASTM A , ASTM B ,  ASTM C ,  ASTM D | 1 || 2 || 3 || 4 || 5 || 6 || 7 || 8 |  , ASTM E , ASTM F , ASTM G

• ASTM D3697 : EN-Standard Test Method for Antimony in Water
• ASTM D3698 : EN-Standard Practice for Solvent Vapor Degreasing Operations
• ASTM D3699 : EN-Standard Specification for Kerosine
• ASTM D3699 REV A : EN-Standard Specification for Kerosine
• ASTM D370 : EN-Standard Test Method for Dehydration of Oil-Type Preservatives
• ASTM D3700 : EN-STANDARD PRACTICE FOR OBTAINING LPG SAMPLES USING A FLOATING PISTON CYLINDER
• ASTM D3701 : EN-STANDARD TEST METHOD FOR HYDROGEN CONTENT OF AVIATION TURBINE FUELS BY LOW RESOLUTION NUCLEAR MAGNETIC RESONANCE SPECTROMETRY (E1-1984)
• ASTM D3701 REV A : EN-Standard Test Method for Hydrogen Content of Aviation Turbine Fuels by Low Resolution Nuclear Magnetic Resonance Spectrometry-IP Designation: 338/98
• ASTM D3702 : EN-STANDARD TEST METHOD FOR WEAR RATE OF MATERIALS IN SELF-LUBRICATED RUBBING CONTACT USING A THRUST WASHER TESTING MACHINE (R 1983) (E1-1984)
• ASTM D3703 : EN-Standard Test Method for Peroxide Number of Aviation Turbine Fuels
• ASTM D3704 : EN-Standard Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion
• ASTM D3705 : EN-Standard Test Method for Misting Properties of Lubricating Fluids
• ASTM D3706 : EN-Standard Test Method for Hot Tack of Wax-Polymer Blends by the Flat Spring Test
• ASTM D3707 : EN-Standard Test Method for Storage Stability of Water-In-Oil Emulsions by the Oven Test Method
• ASTM D3708 : EN-STANDARD TEST METHOD FOR WEIGHT OF WAX APPLIED DURING CURTAIN COATING OPERATION (R 1983)
• ASTM D3709 : EN-STANDARD TEST METHOD FOR STABILITY OF WATER-IN- OIL EMULSIONS UNDER LOW TO AMBIENT TEMPERATURE CYCLING CONDITIONS
• ASTM D371 : EN-STANDARD SPECIFICATION FOR ASPHALT ROLL ROOFING (ORGANIC FELT) SURFACED WITH MINERAL GRANULES; WIDE SELVAGE (R 1984)
• ASTM D3710 : EN-Standard Test Method for Boiling Range Distribution of Gasoline and Gasoline Fractions by Gas Chromatography
• ASTM D3711 : EN-STANDARD TEST METHOD FOR DEPOSITION TENDENCIES OF LIQUIDS IN THIN FILMS AND VAPORS
• ASTM D3712 : EN-Standard Test Method of Analysis of Oil-Soluble Petroleum Sulfonates by Liquid Chromatography
• ASTM D3713 : EN-Standard Test Method for Measuring Response of Solid Plastics to Ignition by a Small Flame
• ASTM D3714 : EN-STANDARD TEST METHOD FOR BLACK MARKING RESISTANCE OF FLOOR POLISHES AS MEASURED BY THE LADDER AND PENDULUM APPARATUS
• ASTM D3715 : EN-STANDARD PRACTICE FOR QUALITY ASSURANCE OF PRESSURE-SENSITIVE TAPES
• ASTM D3715/D3715M : EN-Standard Practice for Quality Assurance of Pressure-Sensitive Tapes
• ASTM D3715M : EN-Standard Practice for Quality Assurance of Pressure-Sensitive Tapes (Metric)
• ASTM D3716 : EN-Standard Test Methods for Use of Emulsion Polymers in Floor Polishes
• ASTM D3717 REV A : EN-Standard Test Method for Low Concentrations of Antimony in Paint by Atomic Absorption Spectroscopy
• ASTM D3718 REV A : EN-Standard Test Method for Low Concentrations of Chromium in Paint by Atomic Absorption Spectroscopy
• ASTM D3719 : EN-Standard Test Method for Quantifying Dirt Collection on Coated Exterior Panels
• ASTM D372 : EN-Standard Specification for Flexible Treated Sleeving Used for Electrical Insulation
• ASTM D3720 : EN-STANDARD TEST METHOD FOR RATIO OF ANATASE TO RUTILE IN TITANIUM DIOXIDE PIGMENTS BY X-RAY DIFFRACTION
• ASTM D3721 : EN-Standard Specification for Synthetic Red Iron Oxide Pigment
• ASTM D3722 : EN-Standard Specification for Natural Red and Brown Iron Oxide Pigments
• ASTM D3723 : EN-Standard Test Method for Pigment Content of Water-Emulsion Paints by Low-Temperature Ashing
• ASTM D3724 : EN-Standard Specification for Synthetic Brown Iron Oxide Pigment
• ASTM D3725 : EN-Standard Test Method for Semiquantitative Determination of Fish Oil in Drying Oils and Drying Oil Fatty Acids by Gas-Liquid Chromatography
• ASTM D3726 : EN-STANDARD SPECIFICATION FOR N-BUTYL ACETATE (99.5% GRADE)
• ASTM D3727 : EN-STANDARD SPECIFICATION FOR ETHYL ACETATE (99.5% GRADE)
• ASTM D3728 : EN-Standard Specification for 2-Ethoxyethyl Acetate (99 % Grade)
• ASTM D3729 : EN-STANDARD SPECIFICATION FOR METHYL ETHYL KETONE (99.5 % GRADE)
• ASTM D373 : EN-STANDARD SPECIFICATION FOR BLACK AND YELLOW STRAIGHT-CUT AND BIAS- CUT VARNISHED COTTON CLOTH AND TAPE FOR ELECTRICAL INSULATION
• ASTM D3730 : EN-Standard Guide for Testing High-Performance Interior Architectural Wall Coatings
• ASTM D3731 : EN-Standard Practices for Measurement of Chlorophyll Content of Algae in Surface Waters
• ASTM D3732 : EN-Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings
• ASTM D3733 : EN-Standard Test Method for Silicon Content of Silicone Polymers and Silicon-Modified Alkyds by Atomic Absorption
• ASTM D3734 : EN-STANDARD SPECIFICATION FOR HIGH-FLASH AROMATIC NAPHTHAS (E1-1985)
• ASTM D3735 : EN-STANDARD SPECIFICATION FOR VM&P NAPHTHAS (E1-1985)
• ASTM D3737 : EN-Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
• ASTM D3737 REV A : EN-STANDARD PRACTICE FOR ESTABLISHING STRESSES FOR STRUCTURAL GLUED LAMINATED TIMBER (GLULAM)
• ASTM D3737 REV B : EN-Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
• ASTM D3737 REV C : EN-STANDARD PRACTICE FOR ESTABLISHING STRESSES FOR STRUCTURAL GLUED LAMINATED TIMBER (GLULAM)
• ASTM D3738 : EN-Standard Specification for Rubber-Coated Cloth Hospital Sheeting
• ASTM D3739 : EN-STANDARD PRACTICE FOR CALCULATION AND ADJUSTMENT OF THE LANGELIER SATURATION INDEX FOR REVERSE OSMOSIS
• ASTM D374 : EN-Standard Test Methods for Thickness of Solid Electrical Insulation
• ASTM D3740 : EN-Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D3740 REV A : EN-Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D3740 REV B : EN-Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D3740 REV C : EN-Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D3741 : EN-Standard Test Method for Appearance of Admixtures Containing Halogenated Organic Solvents
• ASTM D3742 : EN-Standard Test Method for 111-Trichloroethane Content
• ASTM D3743 : EN-Standard Terminology Relating to Bridge Deck and Substructure Protection
• ASTM D3744 : EN-Standard Test Method for Aggregate Durability Index
• ASTM D3745 : EN-STANDARD PRACTICE FOR INSTALLATION OF PREFABRICATED ASPHALT RESERVOIR POND CANAL AND DITCH LINER (EXPOSED TYPE) (R 1989)
• ASTM D3746 : EN-Standard Test Method for Impact Resistance of Bituminous Roofing Systems
• ASTM D3747 : EN-Standard Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation
• ASTM D3748 : EN-Standard Practice for Evaluating High-Density Rigid Cellular Plastics
• ASTM D3749 : EN-Standard Test Method for Residual Vinyl Chloride Monomer in Poly(Vinyl Chloride) Resins by Gas Chromatographic Headspace Technique
• ASTM D374M : EN-Standard Test Methods for Thickness of Solid Electrical Insulation (Metric)
• ASTM D375 : EN-STANDARD SPECIFICATION FOR ASBESTOS ROVING (R 1983) (DISCONTINUED)
• ASTM D375/D375M : EN-Standard Specification for Asbestos Roving
• ASTM D3750 : EN-STANDARD PRACTICE FOR DETERMINATION OF NUMBER-AVERAGE MOLECULAR WEIGHT OF POLYMERS BY MEMBRANE OSMOMETRY
• ASTM D3751 : EN-Standard Practice for Evaluation of Furniture Polish
• ASTM D3751 REV A : EN-STANDARD PRACTICE FOR EVALUATION OF FURNITURE POLISH
• ASTM D3751/D3751M : EN-Standard Practice for Evaluation of Furniture Polish
• ASTM D3752 : EN-Standard Test Method for Strength Imparted by Asbestos to a Cementitious Matrix
• ASTM D3753 : EN-Standard Specification for Glass-Fiber-Reinforced Polyester Manholes and Wetwells
• ASTM D3754 : EN-Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
• ASTM D3755 : EN-Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials under Direct-Voltage Stress
• ASTM D3756 : EN-Standard Test Method for Evaluation of Resistance to Electrical Breakdown by Treeing in Solid Dielectric Materials Using Diverging Fields
• ASTM D3757 : EN-Standard Guide for Preparing Specifications for Solvent Floor Polishes
• ASTM D3758 : EN-Standard Practice for Evaluation of Spray-Buff Products on Test Floors
• ASTM D3759 : EN-STANDARD TEST METHOD FOR TENSILE STRENGTH AND ELONGATION OF PRESSURE- SENSITIVE TAPES
• ASTM D3759/D3759M : EN-Standard Test Method for Tensile Strength and Elongation of Pressure-Sensitive Tapes
• ASTM D3759M : EN-Standard Test Method for Tensile Strength and Elongation of Pressure- Sensitive Tapes (Metric)
• ASTM D3760 : EN-Standard Test Method for Analysis of Isopropylbenzene (Cumene) by Gas Chromatography
• ASTM D3761 : EN-Standard Test Method for Total Fluorine in Coal by the Oxygen Bomb Combustion/Ion Selective Electrode Method
• ASTM D3762 : EN-Standard Test Method for Adhesive-Bonded Surface Durability of Aluminum (Wedge Test)
• ASTM D3763 : EN-Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
• ASTM D3763 REV A : EN-Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
• ASTM D3764 : EN-Standard Practice for Validation of Process Stream Analyzers Systems
• ASTM D3765 : EN-Standard Test Method for Carbon Black – CTAB (Cetyltrimethylammonium Bromide) Surface Area
• ASTM D3765 REV A : EN-Standard Test Method for Carbon Black – CTAB (Cetyltrimethylammonium Bromide) Surface Area
• ASTM D3766 : EN-Standard Terminology Relating to Catalysts and Catalysis
• ASTM D3766 REV A : EN-STANDARD TERMINOLOGY RELATING TO CATALYSTS AND CATALYSIS
• ASTM D3767 : EN-Standard Practice for Rubber – Measurement of Dimensions
• ASTM D3768 : EN-Standard Test Method for Microcellular Urethanes – Flexural Recovery
• ASTM D3769 : EN-Standard Method for Testing Microcellular Urethanes – High- Temperature Sag
• ASTM D3770 : EN-Standard Specification for Flexible Cellular Materials – High-Resilience Polyurethane Foam (HR) and Combustion Modified High Resilience (CMHR) Polyurethane Foam
• ASTM D3771 : EN-Standard Specification for Rubber Seals Used in Concentrating Solar Collectors
• ASTM D3772 : EN-STANDARD SPECIFICATION FOR RUBBER FINGER COTS
• ASTM D3773 : EN-STANDARD TEST METHODS FOR LENGTH OF WOVEN FABRIC
• ASTM D3773/D3773M : EN-Standard Test Methods for Length of Woven Fabric
• ASTM D3774 : EN-Standard Test Methods for Width of Textile Fabric
• ASTM D3775 : EN-Standard Test Method for Fabric Count of Woven Fabric
• ASTM D3775 REV A : EN-Standard Test Method for Warp (End) and Filling (Pick) Count of Woven Fabrics
• ASTM D3776 : EN-Standard Test Methods for Mass Per Unit Area (Weight) of Fabric
• ASTM D3776/D3776M REV A : EN-Standard Test Methods for Mass Per Unit Area (Weight) of Fabric
• ASTM D3777 : EN-Standard Practice for Writing Specifications for Textiles
• ASTM D3778 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN’S AND GIRLS’ DRYCLEANABLE WOVEN DRESS COAT FABRICS-Discontinued 1999
• ASTM D3778 REV A : EN-Standard Performance Specification for Women’s and Girls’ Drycleanable Woven Dress Coat Fabrics
• ASTM D3779 : EN-Standard Performance Specification for Women´s and Girls´ Woven Rainwear and All-Purpose Water-Repellent Coat Fabrics
• ASTM D3779 REV A : EN-Standard Performance Specification for Women´s and Girls´ Woven Rainwear and All-Purpose Water-Repellent Coat Fabrics
• ASTM D378 : EN-Standard Test Methods for Rubber Belting Flat Type
• ASTM D3780 : EN-STANDARD PERFORMANCE SPECIFICATION FOR MEN´S AND BOYS´ WOVEN DRESS SUIT FABRICS AND WOVEN SPORTSWEAR JACKET SLACK AND TROUSER FABRICS
• ASTM D3780 REV A : EN-Standard Performance Specification for Men´s and Boys´ Woven Dress Suit Fabrics and Woven Sportswear Jacket Slack and Trouser Fabrics
• ASTM D3781 : EN-Standard Performance Specification for Men´s and Boys´ Knitted Rainwear and All-Purpose Water-Repellent Coat Fabrics
• ASTM D3782 : EN-Standard Performance Specification for Men´s and Boys´ Knitted Dress Suit Fabrics and Knitted Sportswear Jacket Slack and Trouser Fabrics
• ASTM D3783 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN FLAT LINING FABRICS FOR MEN´S AND BOYS´ APPAREL
• ASTM D3783 REV A : EN-Standard Performance Specification for Woven Flat Lining Fabrics for Men´s and Boys´ Apparel
• ASTM D3784 : EN-STANDARD PERFORMANCE SPECIFICATION FOR MEN´S AND BOYS´ WOVEN BATHROBE AND DRESSING GOWN FABRICS
• ASTM D3784 REV A : EN-Standard Performance Specification for Men´s and Boys´ Woven Bathrobe and Dressing Gown Fabrics
• ASTM D3785 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN NECKTIE AND SCARF FABRICS
• ASTM D3786 : EN-Standard Test Method for Hydraulic Bursting Strength of Knitted Goods and Nonwoven Fabrics – Diaphragm Bursting Strength Tester Method
• ASTM D3786 REV A : EN-Standard Test Method for Bursting Strength of Textile Fabrics-Diaphragm Bursting Strength Tester Method
• ASTM D3786/D3786M : EN-Standard Test Method for Bursting Strength of Textile Fabrics-Diaphragm Bursting Strength Tester Method
• ASTM D3787 : EN-Standard Test Method for Bursting Strength of Knitted Goods – Constant-Rate-Of-Traverse (CRT) Ball Burst Test-(Discontinued 1998; No Replacement)
• ASTM D3787 REV A : EN-STANDARD TEST METHOD FOR BURSTING STRENGTH OF KNITTED GOODS – CONSTANT-RATE-OF- TRAVERSE (CRT) BALL BURST TEST
• ASTM D3788 : EN-STANDARD PRACTICE TO INDICATE DIRECTION OF SPRAY FROM A CAN OF CONSUMER SPRAY PAINT
• ASTM D3789 : EN-Standard Practice for Labeling Cans of Consumer Spray Paint
• ASTM D3790 : EN-Standard Test Method for Volatile Matter (Moisture) of Leather by Oven Drying
• ASTM D3791 : EN-Standard Practice for Evaluating the Effects of Heat on Asphalts
• ASTM D3792 : EN-Standard Test Method for Water Content of Water-Reducible Paints by Direct Injection into a Gas Chromatograph
• ASTM D3793 : EN-Standard Test Method for Low-Temperature Coalescence of Latex Paint Films
• ASTM D3794 : EN-Standard Guide for Testing Coil Coatings
• ASTM D3795 : EN-Standard Test Method for Thermal Flow Cure and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer
• ASTM D3795 REV A : EN-Standard Test Method for Thermal Flow Cure and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer
• ASTM D3796 : EN-Standard Practice for Calibration of Type S Pitot Tubes
• ASTM D3797 : EN-Standard Test Method for Analysis of o-Xylene by Gas Chromatography
• ASTM D3798 : EN-Standard Test Method for Analysis of p-Xylene by Gas Chromatography
• ASTM D3798 REV A : EN-Standard Test Method for Analysis of p-Xylene by Gas Chromatography
• ASTM D3798 REV B : EN-Standard Test Method for Analysis of p-Xylene by Gas Chromatography
• ASTM D3799 : EN-STANDARD TEST METHOD FOR PURITY OF STYRENE BY FREEZING POINT METHOD
• ASTM D38 : EN-STANDARD TEST METHODS FOR SAMPLING WOOD PRESERVATIVES PRIOR TO TESTING (AASHTO T60) (R 1989)
• ASTM D380 : EN-STANDARD METHODS OF TESTING RUBBER HOSE
• ASTM D3800 : EN-Standard Test Method for Density of High-Modulus Fibers
• ASTM D3801 : EN-Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
• ASTM D3802 : EN-Standard Test Method for Ball-Pan Hardness of Activated Carbon
• ASTM D3803 : EN-STANDARD TEST METHODS FOR RADIOIODINE TESTING OF NUCLEAR-GRADE GAS-PHASE ADSORBENTS (E2-1982)
• ASTM D3804 : EN-Standard Test Method for Iron in Paint Driers by EDTA Method
• ASTM D3805 : EN-Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
• ASTM D3805/D3805M : EN-Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
• ASTM D3806 : EN-Standard Test Method of Small-Scale Evaluation of Fire-Retardant Paints (2-Foot Tunnel Method)
• ASTM D3806 REV A : EN-Standard Test Method of Small-Scale Evaluation of Fire-Retardant Paints (2-Foot Tunnel Method)
• ASTM D3807 : EN-Standard Test Method for Strength Properties of Adhesives in Cleavage Peel by Tension Loading (Engineering Plastics-to-Engineering Plastics)
• ASTM D3808 : EN-Standard Test Method for Qualitative Determination of Adhesion of Adhesives to Substrates by Spot Adhesion
• ASTM D3809 : EN-STANDARD METHODS OF TESTING SYNTHETIC DIELECTRIC FLUIDS FOR CAPACITORS (R 1988)
• ASTM D381 : EN-STANDARD TEST METHODS FOR GUM CONTENT IN FUELS BY JET EVAPARATION
• ASTM D3810 : EN-Standard Test Method for Minimum Application Torque of Type IA Child-Resistant Closures
• ASTM D3811 : EN-STANDARD TEST METHOD FOR UNWIND FORCE OF PRESSURE-SENSITIVE TAPES (R 1993)
• ASTM D3811/D3811M : EN-Standard Test Method for Unwind Force of Pressure-Sensitive Tapes
• ASTM D3811M : EN-STANDARD TEST METHOD FOR UNWIND FORCE OF PRESSURE-SENSITIVE TAPES (METRIC) (R 1993)
• ASTM D3813 : EN-Standard Test Method for Curling and Twisting on Unwinding of Pressure- Sensitive Tapes
• ASTM D3813/D3813M : EN-Standard Test Method for Curling Twisting and Tubing on Unwind of Pressure-Sensitive Tapes
• ASTM D3813M : EN-STANDARD TEST METHOD FOR CURLING AND TWISTING ON UNWINDING OF PRESSURE- SENSITIVE TAPES (METRIC) (R 1993)
• ASTM D3814 : EN-STANDARD GUIDE FOR LOCATING COMBUSTION TEST METHODS FOR PLASTICS
• ASTM D3815 : EN-Standard Practice for Accelerated Aging of Pressure-Sensitive Tapes by Carbon-Arc Exposure Apparatus
• ASTM D3815/D3815M : EN-Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Carbon-Arc Exposure Apparatus
• ASTM D3815M : EN-Standard Practice for Accelerated Aging of Pressure-Sensitive Tapes by Carbon-Arc Exposure Apparatus (Metric)
• ASTM D3816 : EN-STANDARD TEST METHOD FOR WATER PENETRATION RATE OF PRESSURE-SENSITIVE TAPES
• ASTM D3816/D3816M : EN-Standard Test Method for Water Penetration Rate of Pressure-Sensitive Tapes
• ASTM D3816M : EN-STANDARD TEST METHOD FOR WATER PENETRATION RATE OF PRESSURE-SENSITIVE TAPES (METRIC)
• ASTM D3817 : EN-STANDARD TEST METHOD FOR MATURITY INDEX OF COTTON FIBERS BY FIBROGRAPH (R 1984) (E1-1984)
• ASTM D3818 : EN-Standard Test Method for Linear Density and Maturity Index of Cotton Fibers (IIC-Shirley Fineness/Maturity Tester)
• ASTM D3819 : EN-STANDARD PERFORMANCE SPECIFICATION FOR MEN´S AND BOYS´ WOVEN PAJAMA FABRICS
• ASTM D3819 REV A : EN-Standard Performance Specification for Men´s and Boys´ Woven Pajama Fabrics
• ASTM D3820 : EN-STANDARD PERFORMANCE SPECIFICATION FOR MEN´S AND BOYS´ WOVEN UNDERWEAR FABRICS
• ASTM D3820 REV A : EN-Standard Performance Specification for Men´s and Boys´ Woven Underwear Fabrics
• ASTM D3821 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN TERRY HOUSEHOLD KITCHEN AND BATH TOWEL FABRICS (R 1993) (E1-1993)
• ASTM D3822 : EN-Standard Test Method for Tensile Properties of Single Textile Fibers
• ASTM D3822 REV A : EN-STANDARD TEST METHOD FOR TENSILE PROPERTIES OF SINGLE TEXTILE FIBERS
• ASTM D3823 : EN-STANDARD PRACTICE FOR DETERMINING TICKET NUMBERS FOR SEWING THREADS
• ASTM D3824 : EN-STANDARD TEST METHODS FOR CONTINUOUS MEASUREMENT OF OXIDES OF NITROGEN IN THE AMBIENT OR WORKPLACE ATMOSPHERE BY THE CHEMILUMINESCENT METHOD
• ASTM D3825 : EN-Standard Test Method for Dynamic Surface Tension by the Fast-Bubble Technique
• ASTM D3826 : EN-Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
• ASTM D3827 : EN-STANDARD METHOD FOR ESTIMATION OF SOLUBILITY OF GASES IN PETROLEUM AND OTHER ORGANIC LIQUIDS
• ASTM D3828 : EN-Standard Test Methods for Flash Point by Small Scale Closed Tester
• ASTM D3828 REV A : EN-Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
• ASTM D3829 : EN-Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil
• ASTM D3830 : EN-STANDARD PRACTICE FOR FILTER MEMBRANE COLOR RATINGS OF AVIATION TURBINE FUELS (R 1984)
• ASTM D3831 : EN-Standard Test Method for Manganese in Gasoline by Atomic Absorption Spectroscopy
• ASTM D3832 : EN-Standard Specification for Rubber Seals Contacting Liquids in Solar Energy Systems
• ASTM D3833 : EN-STANDARD TEST METHOD FOR WATER VAPOR TRANSMISSION OF PRESSURE-SENSITIVE TAPES
• ASTM D3833/D3833M : EN-Standard Test Method for Water Vapor Transmission of Pressure-Sensitive Tapes
• ASTM D3833M : EN-Standard Test Method for Water Vapor Transmission of Pressure-Sensitive Tapes (Metric)
• ASTM D3834 : EN-Standard Test Method for Purity of Vinyl Chloride Monomer by Gas Chromatography
• ASTM D3835 : EN-Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
• ASTM D3835 REV A : EN-STANDARD TEST METHOD FOR DETERMINATION OF PROPERTIES OF POLYMERIC MATERIALS BY MEANS OF A CAPILLARY RHEOMETER
• ASTM D3836 : EN-Standard Practice for Evaluation of Automotive Polish
• ASTM D3836 REV A : EN-STANDARD PRACTICE FOR EVALUATION OF AUTOMOTIVE POLISH
• ASTM D3837 : EN-Standard Practice for Preparing a Solution of Alkali-Soluble Resins
• ASTM D3838 : EN-Standard Test Method for pH of Activated Carbon
• ASTM D3839 : EN-STANDARD PRACTICE FOR UNDERGROUND INSTALLATION OF “FIBERGLASS” (GLASS- FIBER REINFORCED THERMOSETTING RESIN) PIPE
• ASTM D3839 REV A : EN-Standard Practice for Underground Installation of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
• ASTM D3840 : EN-Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications
• ASTM D3841 : EN-STANDARD SPECIFICATION FOR GLASS-FIBER- REINFORCED POLYESTER PLASTIC PANELS
• ASTM D3842 : EN-Standard Guide for Selection of Test Methods for Coatings for Use in Light-Water Nuclear Power Plants
• ASTM D3843 : EN-STANDARD PRACTICE FOR QUALITY ASSURANCE FOR PROTECTIVE COATINGS APPLIED TO NUCLEAR FACILITIES
• ASTM D3844 : EN-Standard Guide for Labeling Halogenated Hydrocarbon Solvent Containers
• ASTM D3845 : EN-Standard Specification for Glacial Methacrylic Acid
• ASTM D3846 : EN-STANDARD TEST METHOD FOR IN-PLANE SHEAR STRENGTH OF REINFORCED PLASTICS
• ASTM D3847 : EN-Standard Practice for Rubber – Directions for Achieving Subnormal Test Temperatures
• ASTM D3848 : EN-Standard Test Methods for Rubber – Evaluation of NBR (Acrylonitrile-Butadiene Copolymers) Mixed with Carbon Black
• ASTM D3849 : EN-Standard Test Method for Carbon BlackMorphological Characterization of Carbon Black Using Electron Microscopy
• ASTM D3849 REV A : EN-Standard Test Method for Carbon Black – Primary Aggregate Dimensions from Electron Microscope Image Analysis
• ASTM D3850 : EN-STANDARD TEST METHOD FOR RAPID THERMAL DEGRADATION OF SOLID ELECTRICAL INSULATING MATERIALS BY THERMOGRAVIMETRIC METHOD
• ASTM D3851 : EN-Standard Specification for Urethane Microcellular Shoe Soling Materials
• ASTM D3852 : EN-STANDARD PRACTICE FOR SAMPLING AND HANDLING PHENOL AND CRESYLIC ACID
• ASTM D3852 REV A : EN-Standard Practice for Sampling and Handling Phenol and Cresylic Acid
• ASTM D3852 REV B : EN-Standard Practice for Sampling and Handling Phenol and Cresylic Acid
• ASTM D3853 : EN-Standard Terminology Relating to Rubber and Rubber LaticesAbbreviations for Chemicals Used in Compounding
• ASTM D3853 REV A : EN-Standard Terminology Relating to Rubber and Rubber Latices – Abbreviations for Chemicals Used in Compounding
• ASTM D3853 REV B : EN-STANDARD TERMINOLOGY RELATING TO RUBBER AND RUBBER LATICES – ABBREVIATIONS FOR CHEMICALS USED IN COMPOUNDING
• ASTM D3854 : EN-Standard Test Method for Rubber Thread – Resistance to Dry Heat
• ASTM D3855 : EN-Standard Test Method for Rubber Thread – Deterioration Due to Standard Washing Solution Treatment
• ASTM D3856 : EN-STANDARD GUIDE FOR EVALUATING LABORATORIES ENGAGED IN SAMPLING AND ANALYSIS OF WATER AND WASTE WATER
• ASTM D3857 : EN-STANDARD PRACTICE FOR MEASUREMENT OF WATER VELOCITY IN OPEN CHANNELS BY ACOUSTIC MEANS
• ASTM D3858 : EN-STANDARD PRACTICE FOR OPEN-CHANNEL FLOW MEASUREMENT OF WATER BY VELOCITY-AREA METHOD (R 1984)
• ASTM D3859 : EN-STANDARD TEST METHODS FOR SELENIUM
• ASTM D3860 : EN-Standard Practice for Determination of Adsorptive Capacity of Activated Carbon by Aqueous Phase Isotherm Technique
• ASTM D3860 REV A : EN-Standard Practice for Determination of Adsorptive Capacity of Activated Carbon by Aqueous Phase Isotherm Technique
• ASTM D3861 : EN-Standard Test Method for Quantity of Water-Extractable Matter in Membrane Filters
• ASTM D3862 : EN-Standard Test Method for Retention Characteristics of 0.2-Micrometer Membrane Filters Used in Routine Filtration Procedures for the Evaluation of Microbiological Water Quality
• ASTM D3863 : EN-Standard Test Method for Retention Characteristics of 0.40 to 0.45-um Membrane Filters Used in Routine Filtration Procedures for the Evaluation of Microbiological Water Quality
• ASTM D3864 : EN-Standard Guide for Continual On-Line Monitoring Systems for Water Analysis
• ASTM D3865 : EN-STANDARD TEST METHOD FOR PLUTONIUM IN WATER
• ASTM D3866 : EN-Standard Test Methods for Silver in Water
• ASTM D3867 : EN-STANDARD TEST METHODS FOR NITRITE-NITRATE IN WATER
• ASTM D3868 : EN-Standard Test Method for Fluoride Ions in Brackish Water Seawater and Brines
• ASTM D3869 : EN-Standard Test Methods for Iodide and Bromide Ions in Brackish Water Seawater and Brines
• ASTM D3869 REV A : EN-STANDARD TEST METHODS FOR IODIDE AND BROMIDE IONS IN BRACKISH WATER SEAWATER AND BRINES
• ASTM D387 : EN-Standard Test Method for Color and Strength of Chromatic Pigments with a Mechanical Muller
• ASTM D3870 : EN-Standard Practice for Establishing Performance Characteristics for Colony Counting Methods in Microbiology
• ASTM D3871 : EN-Standard Test Method for Purgeable Organic Compounds in Water Using Headspace Sampling
• ASTM D3872 : EN-Standard Test Method for Ferrous Iron in Iron Oxides
• ASTM D3873 : EN-Standard Test Method for Valency State of the Arsenic Component of Ammoniacal Copper Arsenate Solutions
• ASTM D3874 : EN-STANDARD TEST METHOD FOR IGNITION OF MATERIALS BY HOT WIRE SOURCES
• ASTM D3874 REV A : EN-Standard Test Method for Ignition of Materials by Hot Wire Sources
• ASTM D3875 : EN-Standard Test Method for Alkalinity in Brackish Water Seawater and Brines
• ASTM D3876 : EN-Standard Test Method for Methoxyl and Hydroxypropyl Substitution in Cellulose Ether Products by Gas Chromatography
• ASTM D3877 : EN-Standard Test Methods for One-Dimensional Expansion Shrinkage and Uplift Pressure of Soil-Lime Mixtures
• ASTM D3878 : EN-Standard Terminology for Composite Materials
• ASTM D3878 REV A : EN-STANDARD TERMINOLOGY OF HIGH-MODULUS REINFORCING FIBERS AND THEIR COMPOSITES
• ASTM D3878 REV B : EN-STANDARD TERMINOLOGY OF HIGH-MODULUS REINFORCING FIBERS AND THEIR COMPOSITES
• ASTM D3878 REV C : EN-STANDARD TERMINOLOGY OF HIGH-MODULUS REINFORCING FIBERS AND THEIR COMPOSITES
• ASTM D3878 REV D : EN-STANDARD TERMINOLOGY OF HIGH-MODULUS REINFORCING FIBERS AND THEIR COMPOSITES
• ASTM D3879 : EN-STANDARD TEST METHOD FOR SAMPLING AMPHIBOLE ASBESTOS
• ASTM D388 : EN-STANDARD CLASSIFICATION OF COALS BY RANK
• ASTM D388 REV A : EN-STANDARD CLASSIFICATION OF COALS BY RANK
• ASTM D388 REV B : EN-STANDARD CLASSIFICATION OF COALS BY RANK
• ASTM D3880 : EN-Standard Test Method for Asbestos Strength Units
• ASTM D3880/D3880M : EN-Standard Test Method for Asbestos Strength Units
• ASTM D3881 : EN-STANDARD SPECIFICATION FOR PHENOLIC TRANSFER- AND INJECTION-MOLDING COMPOUNDS
• ASTM D3882 : EN-Standard Test Method for Bow and Skew in Woven and Knitted Fabrics
• ASTM D3883 : EN-Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics
• ASTM D3884 : EN-Standard Test Method for Abrasion Resistance of Textile Fabrics (Rotary Platform Double-Head Method)
• ASTM D3885 : EN-Standard Test Method for Abrasion Resistance of Textile Fabrics (Flexing and Abrasion Method)
• ASTM D3885 REV A : EN-Standard Test Method for Abrasion Resistance of Textile Fabrics (Flexing and Abrasion Method)
• ASTM D3886 : EN-Standard Test Method for Abrasion Resistance of Textile Fabrics (Inflated Diaphragm Method)
• ASTM D3887 : EN-Standard Specification for Tolerances for Knitted Fabrics
• ASTM D3888 : EN-STANDARD DEFINITIONS OF TERMS RELATING TO OPEN-END SPINNING (R 1985) (E1 – 1985)
• ASTM D3889 : EN-STANDARD TEST METHOD FOR ADHERENCE TO LINERBOARD OF PRESSURE-SENSITIVE TAPE AT LOW TEMPERATURE (R 1993)
• ASTM D3889/D3889M : EN-Standard Test Method for Adherence to Linerboard of Pressure-Sensitive Tape at Low Temperature
• ASTM D3889M : EN-STANDARD TEST METHOD FOR ADHERENCE TO LINEBOARD OF PRESSURE-SENSITIVE TAPE AT LOW-TEMPERATURE (METRIC)
• ASTM D3890 : EN-Standard Test Method for Number of Strokes to Prime a Mechanical Pump Dispenser-Reinstated
• ASTM D3891 : EN-STANDARD PRACTICE FOR PREPARATION OF GLASS PANELS FOR TESTING PAINT VARNISH LACQUER AND RELATED PRODUCTS
• ASTM D3892 : EN-Standard Practice for Packaging/Packing of Plastics
• ASTM D3893 : EN-Standard Test Method for Purity of Methyl Amyl Ketone and Methyl Isoamyl Ketone by Gas Chromatography
• ASTM D3894 : EN-STANDARD TEST METHOD FOR EVALUATION OF FIRE RESPONSE OF RIGID CELLULAR PLASTICS USING A SMALL CORNER CONFIGURATION
• ASTM D3895 : EN-STANDARD TEST METHOD FOR OXIDATIVE-INDUCTION TIME OF POLYOLEFINS BY DIFFERENTIAL SCANNING CALORIMETRY
• ASTM D3896 : EN-Standard Practice for Rubber from Synthetic Sources – Sampling
• ASTM D3897 : EN-Standard Practice for Calculation of Basicity of Chrome Tanning Liquors
• ASTM D3898 : EN-STANDARD TEST METHOD FOR CHROMIC OXIDE IN BASIC CHROMIUM TANNING LIQUORS
• ASTM D3899 : EN-STANDARD SPECIFICATION FOR RUBBER CONTRACEPTIVES – VAGINAL DIAPHRAGMS
• ASTM D390 : EN-STANDARD SPECIFICATION FOR COAL-TAR CREOSOTE FOR THE PRESERVATIVE TREATMENT OF PILES POLES AND TIMBERS FOR MARINE LAND AND FRESH WATER USE
• ASTM D3900 : EN-Standard Test Methods for Rubber Raw – Determination of Ethylene Units in EPM (Ethylene-Propylene Copolymers) and EPDM (Ethylene-Propylene-Diene Terpolymers)
• ASTM D3900 REV A : EN-Standard Test Methods for RubberDetermination of Ethylene Units in Ethylene- Propylene Copolymers (EPM) and in Ethylene-Propylene- Diene Terpolymers (EPDM) by Infrared Spectrometry
• ASTM D3901 : EN-STANDARD CONSUMER PRODUCT SPECIFICATION FOR GARDEN HOSE
• ASTM D3902 : EN-Standard Test Method for Rubber Hose for Gas Diffusion of Liquefied Petroleum Gas
• ASTM D3903 : EN-Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems
• ASTM D3904 : EN-Standard Test Method for Oil from Oil Shale (Resource Evaluation by the Fischer Assay Procedure)
• ASTM D3905 : EN-STANDARD SPECIFICATION FOR TOILET TISSUE INDUSTRIAL
• ASTM D3905 REV A : EN-STANDARD SPECIFICATION FOR TOILET TISSUE FOR INDUSTRIAL AND INSTITUTIONAL USE
• ASTM D3906 : EN-Standard Test Method for Determination of Relative X-ray Diffraction Intensities of Faujasite-Type Zeolite-Containing Materials
• ASTM D3906 REV A : EN-STANDARD TEST METHOD FOR RELATIVE ZEOLITE DIFFRACTION INTENSITIES
• ASTM D3907 : EN-STANDARD METHOD FOR TESTING FLUID CRACKING CATALYSTS BY MICROACTIVITY TEST
• ASTM D3908 : EN-Standard Test Method for Hydrogen Chemisorption on Supported Platinum Catalysts by Volumetric Vacuum Method
• ASTM D3909 : EN-Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
• ASTM D3909 REV A : EN-Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
• ASTM D3909 REV B : EN-Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
• ASTM D391 : EN-Standard Specification for Creosote-Coal Tar Solution
• ASTM D3910 : EN-STANDARD PRACTICES FOR DESIGN TESTING AND CONSTRUCTION OF SLURRY SEAL
• ASTM D3911 : EN-Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
• ASTM D3912 : EN-Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants
• ASTM D3913 : EN-Standard Test Method for Acidity in Basic Chromium Tanning Liquors
• ASTM D3914 : EN-Standard Test Method for in-Plane Shear Strength of Pultruded Glass- Reinforced Plastic Rod
• ASTM D3915 : EN-Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Pressure Applications
• ASTM D3915 REV A : EN-Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Pressure Applications
• ASTM D3916 : EN-Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod
• ASTM D3917 : EN-Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastics Pultruded Shapes
• ASTM D3918 : EN-Standard Terminology Relating to Reinforced Plastic Pultruded Products
• ASTM D3919 : EN-STANDARD PRACTICE FOR MEASURING TRACE ELEMENTS IN WATER BY GRAPHITE FURNACE ATOMIC ABSORPTION SPECTROPHOTOMETRY (R 1989)
• ASTM D3919 REV A : EN-Standard Practice for Measuring Trace Elements in Water by Graphite Furnace Atomic Absorption Spectrophotometry
• ASTM D3920 : EN-STANDARD TEST METHOD FOR STRONTIUM IN WATER
• ASTM D3921 : EN-Standard Test Method for Oil and Grease and Petroleum Hydrocarbons in Water
• ASTM D3922 : EN-STANDARD PRACTICE FOR DETERMINING OPERATING PERFORMANCE OF GRANULAR ACTIVATED CARBON
• ASTM D3923 : EN-STANDARD PRACTICES FOR DETECTING LEAKS IN REVERSE-OSMOSIS DEVICES (R 1989)
• ASTM D3924 : EN-Standard Specification for Standard Environment for Conditioning and Testing Paint Varnish Lacquer and Related Materials
• ASTM D3925 : EN-Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings
• ASTM D3926 : EN-Standard Test Method for Percent Solids in Titanium Dioxide Slurries
• ASTM D3927 : EN-STANDARD GUIDE FOR STATE AND INSTITUTIONAL PURCHASING OF PAINT
• ASTM D3928 : EN-STANDARD METHOD FOR VISUAL EVALUATION OF GLOSS OR SHEEN UNIFORMITY (R 1987)
• ASTM D3928 REV A : EN-Standard Test Method for Evaluation of Gloss or Sheen Uniformity
• ASTM D3929 : EN-STANDARD PRACTICE FOR EVALUATING THE STRESS CRACKING OF PLASTICS BY ADHESIVES USING THE BENT-BEAM METHOD (R 1984)
• ASTM D3930 : EN-STANDARD SPECIFICATION FOR ADHESIVES FOR WOOD- BASED MATERIALS FOR CONSTRUCTION OF MANUFACTURED HOMES
• ASTM D3930 REV A : EN-Standard Specification for Adhesives for Wood-Based Materials for Construction of Manufactured Homes
• ASTM D3931 : EN-STANDARD TEST METHOD FOR DETERMINING STRENGTH OF GAP-FILLING ADHESIVE BONDS IN SHEAR BY COMPRESSION LOADING
• ASTM D3931 REV A : EN-Standard Test Method for Determining Strength of Gap-Filling Adhesive Bonds in Shear by Compression Loading
• ASTM D3932 : EN-STANDARD PRACTICE FOR THE CONTROL OF THE APPLICATION OF STRUCTURAL FASTENERS WHEN ATTACHED BY HOT MELT ADHESIVE
• ASTM D3933 : EN-Standard Guide for Preparation of Aluminum Surfaces for Structural Adhesives Bonding (Phosphoric Acid Anodizing)
• ASTM D3934 : EN-Standard Test Method for Flash/No Flash Test – Equilibrium Method by a Closed-Cup Apparatus
• ASTM D3935 : EN-STANDARD SPECIFICATION FOR POLYCARBONATE (PC) UNFILLED AND REINFORCED MATERIAL (R 1992)
• ASTM D3936 : EN-Standard Test Method for Resistance to Delamination of the Secondary Backing of Pile Yarn Floor Covering
• ASTM D3937 : EN-Standard Test Method for Crimp Frequency of Man-Made Staple Fibers
• ASTM D3938 : EN-STANDARD GUIDE FOR EVALUATION OF TEXTILE PRODUCTS IN RELATION TO REFURBISHING DESCRIBED ON CARE LABELS (R 1990)
• ASTM D3939 : EN-Standard Test Method for Snagging Resistance of Fabrics (Mace)
• ASTM D3939 REV A : EN-Standard Test Method for Snagging Resistance of Fabrics (Mace)
• ASTM D3940 : EN-Bursting Strength (Load) and Elongation of Sewn Seams of Knit or Woven Stretch Textile Fabrics Test Method for
• ASTM D3941 : EN-Standard Test Method for Flash Point by the Equilibrium Method with a Closed-Cup Apparatus
• ASTM D3942 : EN-Standard Test Method for Determination of the Unit Cell Dimension of a Faujasite-Type Zeolite
• ASTM D3943 : EN-Standard Test Method for Total Molybdenum in Fresh Alumina-Base Catalysts
• ASTM D3944 : EN-Standard Test Method for Solidification Point of Petroleum Wax
• ASTM D3945 : EN-Standard Test Methods for Shear Stability of Polymer-Containing Fluids Using a Diesel Injector Nozzle
• ASTM D3946 : EN-STANDARD TEST METHOD FOR EVALUATING THE BIORESISTANCE OF WATER- SOLUBLE METAL-WORKING FLUIDS (R 1986)
• ASTM D3947 : EN-STANDARD TEST METHOD FOR SPECIFIC HEAT OF AIRCRAFT TURBINE LUBRICANTS BY THERMAL ANALYSIS
• ASTM D3948 : EN-Standard Test Method for Determining Water Separation Characteristics of Aviation Turbine Fuels by Portable Separometer
• ASTM D3948 REV A : EN-Standard Test Method for Determining Water Separation Characteristics of Aviation Turbine Fuels by Portable Separometer
• ASTM D3949 : EN-Standard Specification for Coated Glass Fabrics Used for Electrical Insulation
• ASTM D395 : EN-Standard Test Methods for Rubber Property – Compression Set
• ASTM D3950 : EN-Standard Specification for Strapping Nonmetallic (and Joining Methods)
• ASTM D3950 REV A : EN-Standard Specification for Strapping Nonmetallic (and Joining Methods)
• ASTM D3951 : EN-STANDARD PRACTICE FOR COMMERCIAL PACKAGING (R 1994)
• ASTM D3952 : EN-Standard Specification for Rubber Hose Used in Solar Energy Systems
• ASTM D3953 : EN-Standard Specification for Strapping Flat Steel and Seals
• ASTM D3953 REV A : EN-Standard Specification for Strapping Flat Steel and Seals
• ASTM D3954 : EN-STANDARD TEST METHOD FOR DROPPING POINT OF WAXES (R 1989)
• ASTM D3955 : EN-Standard Specification for Electrical Insulating Varnishes
• ASTM D3956 : EN-Standard Specification for Methane Thermophysical Property Tables
• ASTM D3957 : EN-Standard Practices for Establishing Stress Grades for Structural Members Used in Log Buildings
• ASTM D3958 : EN-Standard Test Methods for Rubber-Evaluation of BIIR and CIIR (Halogenated Isobutene-Isoprene Rubber)
• ASTM D3959 : EN-STANDARD METHOD FOR TESTING RUBBER-AND PLASTIC-COATED FABRICS – DISCOLORATION SENSITIVITY TO TOBACCO SMOKE
• ASTM D396 : EN-Standard Specification for Fuel Oils
• ASTM D396 REV A : EN-Standard Specification for Fuel Oils
• ASTM D396 REV B : EN-Standard Specification for Fuel Oils
• ASTM D396 REV C : EN-Standard Specification for Fuel Oils
• ASTM D3960 : EN-Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
• ASTM D3961 : EN-Standard Test Method for Trace Quantities of Sulfur in Liquid Aromatic Hydrocarbons by Oxidative Microcoulometry
• ASTM D3962 : EN-STANDARD TEST METHOD FOR ANALYSIS OF STYRENE BY GAS CHROMATOGRAPHY (R 1989)
• ASTM D3963 : EN-STANDARD SPECIFICATION FOR EPOXY-COATED REINFORCING STEEL
• ASTM D3963/D3963M : EN-Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars
• ASTM D3963/D3963M REV A : EN-Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars
• ASTM D3964 : EN-Standard Practice for Selection of Coating Specimens for Appearance Measurements
• ASTM D3965 : EN-STANDARD SPECIFICATION FOR RIGID ACRYLONITRILE- BUTADIENE-STYRENE (ABS) COMPOUNDS FOR PIPE AND FITTINGS
• ASTM D3966 : EN-Standard Test Method for Piles under Lateral Loads-No Replacement
• ASTM D3967 : EN-Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
• ASTM D3967 REV A : EN-Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
• ASTM D3968 : EN-Standard Test Method for Monitoring of Rotational Torque of Type IIIA Child-Resistant Closures
• ASTM D3969 : EN-Standard Test Method for Zirconium in Paint Driers by EDTA Method
• ASTM D3970 : EN-Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination
• ASTM D3971 : EN-Standard Test Method for Dichloromethane-Soluble Matter in Cellulose
• ASTM D3972 : EN-STANDARD TEST METHOD FOR ISOTOPIC URANIUM IN WATER BY RADIOCHEMISTRY
• ASTM D3973 : EN-Standard Test Method for Low-Molecular Weight Halogenated Hydrocarbons in Water
• ASTM D3974 : EN-Standard Practices for Extraction of Trace Elements from Sediments
• ASTM D3975 : EN-STANDARD PRACTICE FOR PREPARATION OF SAMPLES FOR COLLABORATIVE TESTING OF METHODS FOR ANALYSIS OF SEDIMENTS
• ASTM D3976 : EN-Standard Practice for Preparation of Sediment Samples for Chemical Analysis
• ASTM D3977 : EN-Standard Test Methods for Determining Sediment Concentration in Water Samples
• ASTM D3978 : EN-Standard Practice for Algal Growth Potential Testing with Pseudokirchneriella subcapitata
• ASTM D3979 : EN-STANDARD TEST METHOD FOR PARTICULATE MATTER IN TRICHLOROTRIFLUOROETHANE
• ASTM D3980 : EN-STANDARD PRACTICE FOR INTERLABORATORY TESTING OF PAINT AND RELATED MATERIALS
• ASTM D3981 : EN-Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications
• ASTM D3981 REV A : EN-Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications
• ASTM D3982 : EN-STANDARD SPECIFICATION FOR CUSTOM CONTACT- PRESSURE-MOLDED GLASS- FIBER-REINFORCED THERMOSETTING RESIN HOODS (R 1988)
• ASTM D3983 : EN-STANDARD TEST METHOD FOR MEASURING STRENGTH AND SHEAR MODULUS OF NONRIGID ADHESIVES BY THE THICK-ADHEREND TENSILE-LAP SPECIMEN (R 1991)
• ASTM D3984 : EN-Standard Specification for Ethane Thermophysical Property Tables
• ASTM D3985 : EN-STANDARD TEST METHOD FOR OXYGEN GAS TRANSMISSION RATE THROUGH PLASTIC FILM AND SHEETING USING A COULOMETRIC SENSOR (R 1988) (E1-1988)
• ASTM D3986 : EN-Standard Test Method for Barium in Brines Seawater and Brackish Water by Direct-Current Argon Plasma Atomic Emission Spectroscopy
• ASTM D3987 : EN-Standard Test Method for Shake Extraction of Solid Waste with Water
• ASTM D3988 : EN-Standard Test Method for Vanadium in Paint Driers by EDTA Method
• ASTM D3989 : EN-Standard Test Method for Total Rare Earth Metals in Paint Driers by EDTA Method
• ASTM D3989 REV A : EN-Standard Test Method for Total Rare Earth Metals in Paint Driers by EDTA Method
• ASTM D3990 : EN-STANDARD TERMINOLOGY RELATING TO FABRIC DEFECTS
• ASTM D3990 REV A : EN-STANDARD TERMINOLOGY RELATING TO FABRIC DEFECTS
• ASTM D3991 : EN-Standard Specifications for Fineness of Wool or Mohair and Assignment of Grade
• ASTM D3992 : EN-STANDARD SPECIFICATIONS FOR FINENESS OF WOOL TOP OR MOHAIR TOP AND ASSIGNMENT OF GRADE (R 1991) (E1-1991)
• ASTM D3993 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN THERMAL FLOCKED NONWOVEN AND KNITTED HOUSEHOLD BLANKET FABRICS (R 1990)
• ASTM D3994 : EN-Standard Performance Specification for Woven Swimwear Fabrics
• ASTM D3994 REV A : EN-Standard Performance Specification for Woven Swimwear Fabrics
• ASTM D3995 : EN-MEN´S AND WOMEN´S KNITTED CAREER APPAREL FABRICS: DRESS AND VOCATIONAL PERFORMANCE SPEC. FOR
• ASTM D3996 : EN-Standard Performance Specification for Knit Swimwear Fabrics
• ASTM D3997 : EN-Standard Practice for Preparing Coke Samples for Microscopical Analysis by Reflected Light
• ASTM D3997/D3997M : EN-Standard Practice for Preparing Coke Samples for Microscopical Analysis by Reflected Light
• ASTM D3998 : EN-STANDARD TEST METHOD FOR PENDULUM-IMPACT RESISTANCE OF EXTRUSION PLASTOMETER EXTRUDATES
• ASTM D3999 : EN-Standard Test Methods for the Determination of the Modulus and Damping Properties of Soils Using the Cyclic Triaxial Apparatus
• ASTM D4 : EN-Standard Test Method for Bitumen Content
• ASTM D4000 : EN-STANDARD CLASSIFICATION SYSTEM FOR SPECIFYING PLASTIC MATERIALS
• ASTM D4000 REV A : EN-Standard Classification System for Specifying Plastic Materials
• ASTM D4000 REV B : EN-Standard Classification System for Specifying Plastic Materials
• ASTM D4001 : EN-STANDARD PRACTICE FOR DETERMINATION OF WEIGHT- AVERAGE MOLECULAR WEIGHT OF POLYMERS BY LIGHT SCATTERING (R 1986)
• ASTM D4002 : EN-Standard Practice for Evaluation of Buffable Shoe Polish
• ASTM D4003 : EN-Standard Test Methods for Programmable Horizontal Impact Test for Shipping Containers and Systems
• ASTM D4004 : EN-Standard Test Methods for Rubber – Determination of Metal Content by Flame Atomic Absorption (AAS) Analysis
• ASTM D4005 : EN-Standard Test Method for Plastic-Coated Fabrics – Completeness of Fusion of PVC Dispersion Coatings
• ASTM D4006 : EN-Standard Test Method for Water in Crude Oil by Distillation
• ASTM D4007 : EN-Standard Test Method for Water and Sediment in Crude Oil by the Centrifuge Method (Laboratory Procedure)-API Designation: Chapter 10.3 (MPMS); IP Designation 359/82; E1-1995
• ASTM D4008 : EN-Standard Test Method for Measuring Anti-Soil Deposition Properties of Laundry Detergents (Not Suitable for Detergent Ranking)
• ASTM D4009 : EN-Standard Guide for Foam Stability of Hand Dishwashing Detergents
• ASTM D4010 : EN-Standard Specification for Waterless Hand Cleaner
• ASTM D4011 : EN-Standard Specification for Lotion Soap
• ASTM D4012 : EN-Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Water
• ASTM D4013 : EN-Standard Practice for Preparation of Test Specimens of Bituminous Mixtures by Means of Gyratory Shear Compactor
• ASTM D4014 : EN-STANDARD SPECIFICATION FOR PLAIN AND STEEL- LAMINATED ELASTOMERIC BEARINGS FOR BRIDGES
• ASTM D4015 : EN-STANDARD TEST METHODS FOR MODULUS AND DAMPING OF SOILS BY THE RESONANT- COLUMN METHOD
• ASTM D4016 : EN-Standard Test Method for Viscosity of Chemical Grouts by Brookfield Viscometer (Laboratory Method)
• ASTM D4017 : EN-STANDARD TEST METHOD FOR WATER IN PAINTS AND PAINT MATERIALS BY KARL FISCHER METHOD
• ASTM D4018 : EN-Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
• ASTM D4019 : EN-STANDARD TEST METHOD FOR MOISTURE IN PLASTICS BY COULOMETRY (R 1986)
• ASTM D4019 REV A : EN-Standard Test Method for Moisture in Plastics by Coulometric Regeneration of Phosphorus Pentoxide
• ASTM D402 : EN-Standard Test Method for Distillation of Cutback Asphaltic (Bituminous) Products
• ASTM D4020 : EN-Standard Specification for Ultra-High- Molecular-Weight Polyethylene Molding and Extrusion Materials
• ASTM D4020 REV A : EN-Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials
• ASTM D4021 : EN-Standard Specification for Glass-Fiber-Reinforced Polyester Underground Petroleum Storage Tanks
• ASTM D4022 : EN-STANDARD SPECIFICATION FOR COAL TAR ROOF CEMENT
• ASTM D4023 REV A : EN-Standard Terminology Relating to Humidity Measurements
• ASTM D4024 : EN-Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
• ASTM D4025 : EN-STANDARD PRACTICE FOR REPORTING RESULTS OF EXAMINATION AND ANALYSIS OF DEPOSITS FORMED FROM WATER FOR SUBSURFACE INJECTION (R 1987)
• ASTM D4025 REV A : EN-Standard Practice for Reporting Results of Examination and Analysis of Deposits Formed from Water for Subsurface Injection
• ASTM D4026 : EN-Standard Test Method for Rubber Latex – Styrene-Butadiene Copolymer – Determination of Residual Styrene
• ASTM D4027 : EN-Standard Test Method for Measuring Shear Properties of Structural Adhesives by the Modified-Rail Test
• ASTM D4028 : EN-Standard Specification for Solar Screening Woven from Vinyl-Coated Fiber Glass Yarn
• ASTM D4029 : EN-STANDARD SPECIFICATION FOR FINISHED WOVEN GLASS FABRICS
• ASTM D4029/D4029M : EN-Standard Specification for Finished Woven Glass Fabrics
• ASTM D403 : EN-Methods of Testing and Tolerances for Yarns Containing Wool
• ASTM D4030 : EN-Standard Specification for Glass Fiber Cord and Sewing Thread
• ASTM D4030/D4030M : EN-Standard Specification for Glass Fiber Cord and Sewing Thread
• ASTM D4031 : EN-STANDARD TEST METHOD FOR BULK PROPERTIES OF TEXTURED YARNS (E1-1986) (R 1987)
• ASTM D4031 REV A : EN-Standard Test Method for Bulk Properties of Textured Yarns
• ASTM D4032 : EN-Standard Test Method for Stiffness of Fabric by the Circular Bend Procedure
• ASTM D4033 : EN-Standard Test Method for Resistance to Yarn Slippage at the Sewn Seam in Upholstery Fabrics (Dynamic Fatigue Method)
• ASTM D4034 : EN-STANDARD TEST METHOD FOR RESISTANCE TO YARN SLIPPAGE AT THE SEWN SEAM IN WOVEN UPHOLSTERY FABRICS – PLAIN TUFTED OR FLOCKED
• ASTM D4035 : EN-STANDARD PERFORMANCE SPECIFICATION FOR KNITTED NECKTIE AND SCARF FABRICS
• ASTM D4036 : EN-PERFORMANCE SPECIFICATION FOR WOVEN AND KNIT HOUSEHOLD PILLOWCASE BED SHEET AND CRIB SHEET FABRICS (R 1990)
• ASTM D4037 : EN-PERFORMANCE SPECIFICATION FOR WOVEN KNITTED OR FLOCKED BEDSPREAD FABRICS (R 1990) (E1-1990)
• ASTM D4038 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN’S AND GIRLS’ WOVEN DRESS AND BLOUSE FABRICS
• ASTM D4038 REV A : EN-Standard Performance Specification for Women’s and Girls’ Woven Dress and Blouse Fabrics
• ASTM D4039 : EN-Standard Test Method for Reflection Haze of High-Gloss Surfaces
• ASTM D4040 : EN-STANDARD TEST METHOD FOR VISCOSITY OF PRINTING INKS AND VEHICLES BY THE FALLING-ROD VISCOMETER
• ASTM D4041 : EN-Standard Practice for Determining Spray Patterns of Manually Operated Pump Dispensers
• ASTM D4042 : EN-Test Method for Sampling and Testing for Ash and Total Iron in Steel Mill Dispersions of Rolling Oils
• ASTM D4043 : EN-Standard Guide for Selection of Aquifer- Test Method in Determining of Hydraulic Properties by Well Techniques
• ASTM D4044 : EN-Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifers
• ASTM D4045 : EN-Standard Test Method for Sulfur in Petroleum Products by Hydrogenolysis and Rateometric Colorimetry
• ASTM D4046 : EN-STANDARD TEST METHOD FOR ALKYL NITRATE IN DIESEL FUELS BY SPECTROPHOTOMETRY
• ASTM D4047 : EN-Standard Test Method for Phosphorus in Lubricating Oils and Additives by Quinoline Phosphomolybdate Method-IP Designation: 149/93
• ASTM D4048 : EN-Standard Test Method for Detection of Copper Corrosion from Lubricating Grease
• ASTM D4049 : EN-Standard Test Method for Determining the Resistance of Lubricating Grease to Water Spray
• ASTM D4050 : EN-Standard Test Method (Field Procedure) for Withdrawal and Injection Well Tests for Determining Hydraulic Properties of Aquifer Systems
• ASTM D4051 : EN-Standard Practice for Preparation of Low-Pressure Gas Blends
• ASTM D4052 : EN-Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter-X´A6´hNX´A6´hM IP Designation: 365/84(86)
• ASTM D4053 : EN-Standard Test Method for Benzene in Motor and Aviation Gasoline by Infrared Spectroscopy
• ASTM D4054 : EN-STANDARD PRACTICE FOR EVALUATING THE COMPATIBILITY OF ADDITIVES WITH AVIATION-TURBINE FUELS AND AIRCRAFT FUEL SYSTEM MATERIALS (R 1987)
• ASTM D4055 : EN-Standard Test Method for Pentane Insolubles by Membrane Filtration
• ASTM D4056 : EN-Standard Test Method for Estimation of Solubility of Water in Hydrocarbon and Aliphatic Ester Lubricants
• ASTM D4057 : EN-STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS (API DESIGNATION: MPMS (CHAPTER 8.1)) (E1-1989)
• ASTM D4058 : EN-STANDARD TEST METHOD FOR ATTRITION AND ABRASION OF CATALYSTS AND CATALYST CARRIERS
• ASTM D4059 : EN-Standard Test Method for Analysis of Polychlorinated Biphenyls in Insulating Liquids by Gas Chromatography
• ASTM D4060 : EN-STANDARD TEST METHOD FOR ABRASION RESISTANCE OF ORGANIC COATINGS BY THE TABER ABRASER
• ASTM D4061 : EN-Standard Test Method for Retroreflectance of Horizontal Coatings
• ASTM D4061 REV A : EN-STANDARD TEST METHOD FOR RETROREFLECTANCE OF HORIZONTAL COATINGS
• ASTM D4061 REV B : EN-STANDARD TEST METHOD FOR RETROREFLECTANCE OF HORIZONTAL COATINGS
• ASTM D4062 : EN-Standard Test Method for Leveling of Paints by Draw-Down Method
• ASTM D4063 : EN-Standard Specification for Pressboard for Electrical Insulating Purposes
• ASTM D4064 : EN-Standard Practice for Preservative Treatment of Utility Poles by the Thermal Process
• ASTM D4065 : EN-STANDARD PRACTICE FOR DETERMINING AND REPORTING DYNAMIC MECHANICAL PROPERTIES OF PLASTICS
• ASTM D4065 REV A : EN-STANDARD PRACTICE FOR DETERMINING AND REPORTING DYNAMIC MECHANICAL PROPERTIES OF PLASTICS
• ASTM D4066 : EN-STANDARD SPECIFICATION FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA)
• ASTM D4066 REV A : EN-Standard Classification System for Nylon Injection and Extrusion Materials (PA)
• ASTM D4066 REV B : EN-Standard Specification for Nylon Injection and Extrusion Materials (PA)
• ASTM D4067 : EN-STANDARD SPECIFICATION FOR REINFORCED AND FILLED POLYPHENYLENE SULFIDE (PPS) INJECTION MOLDING AND EXTRUSION MATERIALS
• ASTM D4068 : EN-STANDARD SPECIFICATION FOR CHLORINATED POLYETHYLENE (CPE) SHEETING FOR CONCEALED WATER-CONTAINMENT MEMBRANE
• ASTM D4068 REV A : EN-STANDARD SPECIFICATION FOR CHLORINATED POLYETHYLENE (CPE) SHEETING FOR CONCEALED WATER-CONTAINMENT MEMBRANE
• ASTM D4069 : EN-STANDARD SPECIFICATION FOR IMPREGNATED ACTIVATED CARBON USED TO REMOVE GASEOUS RADIO- IODINES FROM GAS STREAMS
• ASTM D4070 : EN-Standard Specification for Adhesive Lubricant for Installation of Preformed Elastomeric Bridge Compression Seals in Concrete Structures
• ASTM D4071 : EN-Standard Practice for Use of Portland Cement Concrete Bridge Deck Water Barrier Membrane Systems
• ASTM D4072 : EN-Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch
• ASTM D4073 : EN-STANDARD TEST METHOD FOR TENSILE-TEAR STRENGTH OF BITUMINOUS ROOFING MEMBRANES (R 1990)
• ASTM D4074 : EN-Standard Test Method for Bitumen and Aggregate Content of Bitumen-Aggregate Mixtures from Roofing Samples
• ASTM D4075 : EN-Standard Test Methods for Rubber Compounding MaterialsFlame Atomic Absorption AnalysisDetermination of Metals
• ASTM D4076 : EN-STANDARD SPECIFICATION FOR o-XYLENE 950 (R 1990)
• ASTM D4077 : EN-Standard Specification for Cumene (Isopropylbenzene)
• ASTM D4078 : EN-Standard Specification for Water Emulsion Floor Polish
• ASTM D4079 : EN-Standard Specification for Vapor-Degreasing Grade Methylene Chloride
• ASTM D4080 : EN-Standard Specification for Trichloroethylene Technical and Vapor-Degreasing Grade
• ASTM D4081 : EN-Standard Specification for Drycleaning-Grade Perchloroethylene
• ASTM D4082 : EN-STANDARD TEST METHOD FOR EFFECTS OF GAMMA RADIATION ON COATINGS FOR USE IN LIGHT-WATER NUCLEAR POWER PLANTS
• ASTM D4083 : EN-Standard Practice for Description of Frozen Soils (Visual-Manual Procedure)
• ASTM D4084 : EN-Standard Test Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method)
• ASTM D4085 : EN-STANDARD TEST METHOD FOR METALS IN CELLULOSE BY ATOMIC ABSORPTION SPECTROPHOTOMETRY (R 1987)
• ASTM D4086 : EN-STANDARD PRACTICE FOR VISUAL EVALUATION OF METAMERISM (R 1986)
• ASTM D4086 REV A : EN-Standard Practice for Visual Evaluation of Metamerism
• ASTM D4088 : EN-Standard Practice for Preparation for Shipment of Solid Electrical Insulating Materials
• ASTM D4089 : EN-STANDARD SPECIFICATION FOR HEAVY-DUTY CHLORINATED POLYETHYLENE (CPE) JACKET FOR WIRE AND CABLE
• ASTM D409 : EN-STANDARD TEST METHOD FOR GRINDABILITY OF COAL BY THE HARDGROVE-MACHINE METHOD
• ASTM D409 REV A : EN-Standard Test Method for Grindability of Coal by the Hardgrove-Machine Method
• ASTM D409/D409M : EN-Standard Test Method for Grindability of Coal by the Hardgrove-Machine Method
• ASTM D409/D409M REV A : EN-Standard Test Method for Grindability of Coal by the Hardgrove-Machine Method
• ASTM D4090 : EN-STANDARD SPECIFICATION FOR GENERAL-PURPOSE CHLORINATED POLYETHYLENE (CPE) JACKET FOR WIRE AND CABLE
• ASTM D4091 : EN-STANDARD SPECIFICATION FOR EXTRA HEAVY-DUTY BLACK CHLORINATED POLYETHYLENE (CPE) JACKET FOR WIRE AND CABLE
• ASTM D4092 : EN-Standard Terminology Relating to Dynamic Mechanical Measurements on Plastics
• ASTM D4092 REV A : EN-STANDARD DEFINITIONS AND DESCRIPTIONS OF TERMS RELATING TO DYNAMIC MECHANICAL MEASUREMENTS ON PLASTICS
• ASTM D4093 : EN-Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials
• ASTM D4094 : EN-Standard Test Method for Acid Content of Ethylene-Acrylic Acid Copolymers
• ASTM D4095 : EN-Standard Practice for Use of the Refractometer for Determining Nonvolatile Matter (Total Solids) in Floor Polishes
• ASTM D4096 : EN-STANDARD PRACTICE FOR APPLICATION OF THE HI-VOL (HIGH-VOLUME) SAMPLER METHOD FOR COLLECTION AND MASS DETERMINATION OF AIRBORNE PARTICULATE MATTER
• ASTM D4097 : EN-STANDARD SPECIFICATION FOR CONTACT-MOLDED GLASS-FIBER-REINFORCED THERMOSET RESIN CHEMICAL-RESISTANT TANKS (E1-1988)
• ASTM D4097 REV A : EN-Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
• ASTM D4098 : EN-Standard Practice for Evaluating High-Density Rigid Cellular Thermosets
• ASTM D4099 : EN-Standard Specification for Poly(Vinyl Chloride) (PVC) Prime Windows/Sliding Glass Doors
• ASTM D41 : EN-Standard Specification for Asphalt Primer Used in Roofing Dampproofing and Waterproofing-E-1; AASHTO No.: M116
• ASTM D410 : EN-STANDARD METHOD FOR SIEVE ANALYSIS OF COAL
• ASTM D4100 : EN-Standard Test Method for Gravimetric Determination of Smoke Particulates from Combustion of Plastic Materials
• ASTM D4101 : EN-Standard Specification for Polypropylene Injection and Extrusion Materials
• ASTM D4101 REV A : EN-Standard Specification for Polypropylene Injection and Extrusion Materials
• ASTM D4101 REV B : EN-STANDARD SPECIFICATION FOR PROPYLENE PLASTIC INJECTION AND EXTRUSION MATERIALS
• ASTM D4102 : EN-Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers
• ASTM D4103 : EN-Standard Practice for Preparation of Substrate Surfaces for Coefficient of Friction Testing
• ASTM D4104 : EN-Standard Test Method (Analytical Procedure) for Determining Transmissivity of Nonleaky Confined Aquifers by Overdamped Well Response to Instantaneous Change in Head (Slug Tests)
• ASTM D4105 : EN-Standard Test Method (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Modified Theis Nonequilibrium Method
• ASTM D4106 : EN-Standard Test Method (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis Nonequilibrium Method
• ASTM D4107 : EN-Standard Test Method for Tritium in Drinking Water
• ASTM D4108 : EN-STANDARD TEST METHOD FOR THERMAL PROTECTIVE PERFORMANCE OF MATERIALS FOR CLOTHING BY OPEN-FLAME METHOD
• ASTM D4109 : EN-STANDARD PERFORMANCE SPECIFICATION FOR MEN´S AND BOYS´ WOVEN COVERALL DUNGAREE OVERALL AND SHOP-COAT FABRICS
• ASTM D4109 REV A : EN-Standard Performance Specification for Men´s and Boys´ Woven Coverall Dungaree Overall and Shop-Coat Fabrics
• ASTM D411 : EN-Standard Test Methods for Shellac Used for Electrical Insulation
• ASTM D4110 : EN-Standard Performance Specification for Men´s and Boys´ Knitted Bathrobe Dressing Gown and Pajama Fabrics
• ASTM D4111 : EN-Standard Performance Specification for Woven Napery and Tablecloth Fabrics: Household and Institutional
• ASTM D4112 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN UMBRELLA FABRIC
• ASTM D4112 REV A : EN-Standard Performance Specification for Woven Umbrella Fabrics
• ASTM D4113 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN SLIPCOVER FABRICS
• ASTM D4113 REV A : EN-Standard Performance Specification for Woven Slipcover Fabrics
• ASTM D4114 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN FLAT LINING FABRICS FOR WOMEN´S AND GIRLS´ APPAREL
• ASTM D4114 REV A : EN-Standard Performance Specification for Woven Flat Lining Fabrics for Women´s and Girls´ Apparel
• ASTM D4115 : EN-Standard Performance Specification for Women´s and Girls´ Knitted and Woven Dress Glove Fabrics
• ASTM D4115 REV A : EN-Standard Performance Specification for Women´s and Girls´ Knitted and Woven Dress Glove Fabrics
• ASTM D4116 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN´S AND GIRLS´ KNITTED AND WOVEN CORSET-GIRDLE- COMBINATION FABRICS
• ASTM D4116 REV A : EN-Standard Performance Specification for Women´s and Girls´ Knitted and Woven Corset-Girdle-Combination Fabrics
• ASTM D4117 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN´S AND GIRLS´ WOVEN ROBE NEGLIGEE NIGHTGOWN PAJAMA SLIP AND LINGERIE FABRICS
• ASTM D4117 REV A : EN-Standard Performance Specification for Women´s and Girls´ Woven Robe Negligee Nightgown Pajama Slip and Lingerie Fabrics
• ASTM D4118 : EN-Standard Performance Specification for Women-s Woven Coverall Dungaree Overall and Shop Coat Fabrics
• ASTM D4118 REV A : EN-Standard Performance Specification for Women´s Woven Coverall Dungaree Overall and Shop Coat Fabrics
• ASTM D4119 : EN-Standard Performance Specification for Men-s and Boys- Knitted Dress Shirt Fabrics
• ASTM D412 : EN-Standard Method of Tension Testing of Vulcanized Rubber
• ASTM D412 REV A : EN-Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers – Tension
• ASTM D4120 : EN-STANDARD TEST METHOD FOR FIBER COHESION IN ROVING SLIVER AND TOP IN DYNAMIC TESTS
• ASTM D4121 : EN-STANDARD PRACTICE FOR PHOTOGRAPHIC DOCUMENTATION OF COATING AND LINING FAILURES AND DEFECTS
• ASTM D4122 : EN-Standard Practice for Carbon Black Evaluation of an Industry Reference Black
• ASTM D4122 REV A : EN-Standard Practice for Carbon BlackEvaluation of an Industry Reference Black
• ASTM D4123 : EN-Standard Test Method for Indirect Tension Test for Resilient Modulus of Bituminous Mixtures
• ASTM D4124 : EN-Standard Test Method for Separation of Asphalt into Four Fractions
• ASTM D4125 : EN-Standard Test Methods for Asphalt Content of Bituminous Mixtures by the Nuclear Method
• ASTM D4126 : EN-Standard Specification for Vapor-Degreasing Grade and General Solvent Grade 111-Trichloroethane
• ASTM D4127 : EN-Standard Terminology Used with Ion-Selective Electrodes
• ASTM D4128 : EN-Standard Guide for Identification and Quantitation of Organic Compounds in Water by Combined Gas Chromatography and Electron Impact Mass Spectrometry
• ASTM D4129 : EN-Standard Test Method for Total and Organic Carbon in Water by High Temperature Oxidation and by Coulometric Detection
• ASTM D413 : EN-Standard Test Methods for Rubber Property – Adhesion to Flexible Substrate
• ASTM D4130 : EN-Standard Test Method for Sulfate Ion in Brackish Water Seawater and Brines
• ASTM D4131 : EN-Standard Practice for Sampling Fish with Rotenone
• ASTM D4132 : EN-Standard Practice for Sampling Phytoplankton with Conical Tow Nets
• ASTM D4133 : EN-Standard Practice for Sampling Phytoplankton with Pumps
• ASTM D4134 : EN-Standard Practice for Sampling Phytoplankton with a Clarke-Bumpus Plankton Sampler
• ASTM D4135 : EN-Standard Practice for Sampling Phytoplankton With Depth-Integrating Samplers
• ASTM D4136 : EN-Standard Practice for Sampling Phytoplankton with Water-Sampling Bottles
• ASTM D4137 : EN-Standard Practice for Preserving Phytoplankton Samples
• ASTM D4138 : EN-Standard Test Methods for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Means
• ASTM D4138 REV A : EN-Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Cross-Sectioning Means
• ASTM D4139 : EN-Standard Guide for Determining Volatile and Nonvolatile Content of Pigments
• ASTM D4140 : EN-Standard Guide for Determining Volatile and Nonvolatile Content of Driers Drying Oils Naval Stores and Solvents
• ASTM D4141 : EN-Standard Practice for Conducting Black Box and Solar Concentrating Exposures of Coatings
• ASTM D4142 : EN-Standard Guide for Testing Epoxy Resins
• ASTM D4143 : EN-Standard Guide for Testing Latex Vehicles
• ASTM D4144 : EN-STANDARD METHOD FOR ESTIMATING PACKAGE STABILITY OF COATINGS FOR ULTRAVIOLET CURING (R 1987)
• ASTM D4145 : EN-Standard Test Method for Coating Flexibility of Prepainted Sheet
• ASTM D4146 : EN-Standard Test Method for Formability of Zinc-Rich Primer/Chromate Complex Coatings on Steel
• ASTM D4147 : EN-Standard Practice for Applying Coil Coatings Using the Wire-Wound Drawdown Bar
• ASTM D4148 : EN-Standard Test Method for Analysis of Phytoplankton in Surface Water by the Sedgwick-Rafter Method
• ASTM D4149 : EN-Standard Classification for Sampling Phytoplankton in Surface Waters
• ASTM D4150 : EN-STANDARD TERMINOLOGY RELATING TO GASEOUS FUELS
• ASTM D4151 : EN-Standard Test Method for Flammability of Blankets
• ASTM D4152 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOVEN INSTITUTIONAL DISH HUCK AND TERRY BATH TOWEL FABRICS
• ASTM D4153 : EN-STANDARD PERFORMANCE SPECIFICATION FOR MEN´S WOMEN´S AND CHILDREN´S WOVEN HANDKERCHIEF FABRICS
• ASTM D4153 REV A : EN-Standard Performance Specification for Men´s Women´s and Children´s Woven Handkerchief Fabrics
• ASTM D4154 : EN-STANDARD PERFORMANCE SPECIFICATION FOR MEN´S AND BOYS´ KNITTED AND WOVEN BEACHWEAR AND SPORTS SHIRT FABRICS
• ASTM D4154 REV A : EN-Standard Performance Specification for Men´s and Boys´ Knitted and Woven Beachwear and Sports Shirt Fabrics
• ASTM D4155 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN´S AND GIRLS´ WOVEN SPORTSWEAR SHORTS SLACKS AND SUITING FABRICS
• ASTM D4155 REV A : EN-Standard Performance Specification for Women´s and Girls´ Woven Sportswear Shorts Slacks and Suiting Fabrics
• ASTM D4156 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN´S AND GIRLS´ KNITTED SPORTSWEAR FABRICS
• ASTM D4157 : EN-Standard Test Method for Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method)-(Discontinued 2001; No Replacement)
• ASTM D4158 : EN-STANDARD TEST METHOD FOR ABRASION RESISTANCE OF TEXTILE FABRICS (UNIFORM ABRASION METHOD)
• ASTM D4159 : EN-STANDARD TEST METHOD FOR RESISTANCE TO YARN SLIPPAGE IN WOVEN UPHOLSTERY FABRICS – PLAIN TUFTED OR FLOCKED (USING A SIMULATED SEAM)
• ASTM D4160 : EN-STANDARD SPECIFICATION FOR REINFORCED THERMOSETTING RESIN PIPE (RTRP) FITTINGS FOR NONPRESSURE APPLICATIONS
• ASTM D4161 : EN-Standard Specification for “Fiberglass” (Glass- Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
• ASTM D4162 : EN-STANDARD SPECIFICATION FOR REINFORCED THERMOSETTING RESIN SEWER AND INDUSTRIAL PRESSURE PIPE (RTRP)
• ASTM D4163 : EN-STANDARD SPECIFICATION FOR REINFORCED THERMOSETTING RESIN PRESSURE PIPE (RTRP)
• ASTM D4164 : EN-Standard Test Method for Mechanically Tapped Packing Density of Formed Catalyst and Catalyst Carriers
• ASTM D4165 : EN-Standard Test Method for Cyanogen Chloride in Water
• ASTM D4166 : EN-Standard Test Method for Measurement of Thickness of Nonmagnetic Materials by Means of a Digital Magnetic Intensity Instrument
• ASTM D4167 : EN-Standard Specification for Fiber-Reinforced Plastic Fans and Blowers
• ASTM D4168 : EN-Standard Test Methods for Transmitted Shock Characteristics of Foam-in-Place Cushioning Materials
• ASTM D4169 : EN-Standard Practice for Performance Testing of Shipping Containers and Systems
• ASTM D4169 REV A : EN-STANDARD PRACTICE FOR PERFORMANCE TESTING OF SHIPPING CONTAINERS AND SYSTEMS
• ASTM D4170 : EN-Standard Test Method for Fretting Wear Protection by Lubricating Greases
• ASTM D4171 : EN-Standard Specification for Fuel System Icing Inhibitors
• ASTM D4171 REV A : EN-Standard Specification for Fuel System Icing Inhibitors
• ASTM D4172 : EN-Standard Test Method for Wear Preventive Characteristics of Lubricating Fluid (Four-Ball Method)
• ASTM D4173 : EN-STANDARD PRACTICE FOR EVALUATING SHEET METAL FORMING LUBRICANT
• ASTM D4174 : EN-Standard Practice for Cleaning Flushing and Purification of Petroleum Fluid Hydraulic Systems
• ASTM D4175 : EN-Standard Terminology Relating to Petroleum Petroleum Products and Lubricants
• ASTM D4175 REV A : EN-Standard Terminology Relating to Petroleum Petroleum Products and Lubricants
• ASTM D4175 REV B : EN-Standard Terminology Relating to Petroleum Petroleum Products and Lubricants
• ASTM D4176 : EN-STANDARD TEST METHOD FOR FREE WATER AND PARTICULATE CONTAMINATION IN DISTILLATE FUELS (CLEAR AND BRIGHT PASS/FAIL PROCEDURES)
• ASTM D4177 : EN-Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
• ASTM D4178 : EN-Standard Practice for Calibrating Moisture Analyzers
• ASTM D4179 : EN-Standard Test Method for Single Pellet Crush Strength of Formed Catalyst Shapes
• ASTM D4179 REV A : EN-Standard Test Method for Single Pellet Crush Strength of Formed Catalyst Shapes
• ASTM D418 : EN-STANDARD TEST METHODS FOR TUFT AND YARN LENGTH OF UNCOATED FLOOR COVERINGS
• ASTM D4180 : EN-Standard Test Method for Vibratory Packing Density of Formed Catalyst Particles and Catalyst Carriers
• ASTM D4181 : EN-Standard Specification for Acetal (POM) Molding and Extrusion Materials
• ASTM D4181 REV A : EN-STANDARD SPECIFICATION FOR ACETAL (POM) MOLDING AND EXTRUSION MATERIALS (E1-1994)
• ASTM D4182 : EN-Standard Practice for Evaluation of Laboratories Using ASTM Procedures in the Sampling and Analysis of Coal and Coke
• ASTM D4182 REV A : EN-STANDARD PRACTICE FOR EVALUATION OF LABORATORIES USING ASTM PROCEDURES IN THE SAMPLING AND ANALYSIS OF COAL AND COKE
• ASTM D4183 : EN-STANDARD TEST METHODS FOR TOTAL RECOVERABLE PHOSPHORUS AND ORGANIC PHOSPHORUS IN SEDIMENTS
• ASTM D4184 : EN-STANDARD SPECIFICATION FOR REINFORCED THERMOSETTING RESIN (RTRP) SEWER PIPE
• ASTM D4185 : EN-Standard Practice for Measurement of Metals in Workplace Atmospheres by Flame Atomic Absorption Spectrophotometry
• ASTM D4186 : EN-STANDARD TEST METHOD FOR ONE-DIMENSIONAL CONSOLIDATION PROPERTIES OF SOILS USING CONTROLLED-STRAIN LOADING
• ASTM D4187 : EN-STANDARD TEST METHODS FOR ZETA POTENTIAL OF COLLOIDS IN WATER AND WASTE WATER
• ASTM D4188 : EN-Standard Practice for Performing Pressure In-Line Coagulation-Flocculation- Filtration Test
• ASTM D4189 : EN-Standard Test Method for Silt Density Index (SDI) of Water
• ASTM D4190 : EN-Standard Test Method for Elements in Water by Direct-Current Plasma Atomic Emission Spectroscopy
• ASTM D4190 REV A : EN-Standard Test Method for Elements in Water by Direct-Current Argon Plasma Atomic Emission Spectroscopy
• ASTM D4191 : EN-Standard Test Method for Sodium in Water by Atomic Absorption Spectrophotometry
• ASTM D4192 : EN-Standard Test Method for Potassium in Water by Atomic Absorption Spectrophotometry
• ASTM D4193 : EN-Standard Test Method for Thiocyanate in Water
• ASTM D4194 : EN-STANDARD TEST METHODS FOR OPERATING CHARACTERISTICS OF REVERSE OSMOSIS DEVICES (R 1994)
• ASTM D4195 : EN-Standard Guide for Water Analysis for Reverse Osmosis Application
• ASTM D4196 : EN-Standard Test Method for Confirming the Sterility of Membrane Filters
• ASTM D4197 : EN-STANDARD TEST METHODS FOR PERCENT POROSITY OF MEMBRANE FILTERS
• ASTM D4198 : EN-Standard Test Methods for Evaluating Absorbent Pads Used with Membrane Filters for Bacteriological Analysis and Growth
• ASTM D4199 : EN-Standard Test Methods for Autoclavability of Membrane Filters
• ASTM D420 : EN-Standard Guide to Site Characterization for Engineering Design and Construction Purposes
• ASTM D4200 : EN-Standard Test Method for Evaluating Inhibitory Effects of Ink Grids on Membrane Filters
• ASTM D4201 : EN-Standard Test Method for Coliphages in Water
• ASTM D4202 : EN-Standard Test Method for Thermal Stability of Poly(Vinyl Chloride) (PVC) Resin
• ASTM D4203 : EN-Standard Specification for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials
• ASTM D4204 : EN-Standard Practice for Preparing Plastic Film Specimens for a Round-Robin Study
• ASTM D4205 : EN-STANDARD GUIDE FOR FLAMMABILITY AND COMBUSTION TESTING OF RUBBER
• ASTM D4205 REV A : EN-STANDARD GUIDE FOR FLAMMABILITY AND COMBUSTION TESTING OF RUBBER
• ASTM D4206 : EN-STANDARD TEST METHOD FOR SUSTAINED BURNING OF LIQUID MIXTURES BY THE SETAFLASH APPARATUS (OPEN CUP)
• ASTM D4207 : EN-Standard Test Method for Sustained Burning of Low-Viscosity Liquid Mixtures by the Wick Test
• ASTM D4208 : EN-Standard Test Method for Total Chlorine in Coal by the Oxygen Bomb Combustion/Ion Selective Electrode Method
• ASTM D4209 : EN-Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics Emulsions Resin Solutions Shellac and Varnishes
• ASTM D421 : EN-Standard Practice for Dry Preparation of Soil Samples for Particle-Size Analysis and Determination of Soil Constants
• ASTM D4210 : EN-Standard Practice for Intralaboratory Quality Control Procedures and a Discussion on Reporting Low-Level Data
• ASTM D4211 : EN-Classification for Fish Sampling
• ASTM D4212 : EN-Standard Test Method for Viscosity by Dip-Type Viscosity Cups
• ASTM D4213 : EN-STANDARD TEST METHOD FOR WET ABRASION RESISTANCE OF INTERIOR PAINTS
• ASTM D4214 : EN-Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films
• ASTM D4215 : EN-Standard Specification for Cold-Mixed Cold-Laid Bituminous Paving Mixtures
• ASTM D4216 : EN-STANDARD SECIFICATION FOR RIGID POLY(VINYL CHLORIDE) (PVC) AND RELATED PLASTIC BUILDING PRODUCTS COMPOUNDS
• ASTM D4217 : EN-Standard Test Method for Gel Time of Thermosetting Coating Powder
• ASTM D4218 : EN-Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
• ASTM D4219 : EN-Standard Test Method for Unconfined Compressive Strength Index of Chemical- Grouted Soils
• ASTM D4219 REV A : EN-Standard Test Method for Unconfined Compressive Strength Index of Chemical-Grouted Soils
• ASTM D422 : EN-Standard Test Method for Particle-Size Analysis of Soils
• ASTM D4220 : EN-Standard Practices for Preserving and Transporting Soil Samples
• ASTM D4221 : EN-Standard Test Method for Dispersive Characteristics of Clay Soil by Double Hydrometer
• ASTM D4221 REV A : EN-STANDARD TEST METHOD FOR DISPERSIVE CHARACTERISTICS OF CLAY SOIL BY DOUBLE HYDROMETER
• ASTM D4222 : EN-Standard Test Method for Determination of Nitrogen Adsorption and Desorption Isotherms of Catalysts by Static Volumetric Measurements
• ASTM D4223 : EN-STANDARD PRACTICE FOR PREPARATION OF TEST SPECIMENS OF ASPHALT- STABILIZED SOILS (R 1990)
• ASTM D4224 : EN-STANDARD TEST METHOD FOR ANIONIC DETERGENT BY PARA-TOLUIDINE HYDROCHLORIDE
• ASTM D4225 : EN-STANDARD SPECIFICATION FOR STYRENE-BUTADIENE SHEETING
• ASTM D4226 : EN-Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products
• ASTM D4226 REV A : EN-Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products
• ASTM D4227 : EN-Standard Practice for Qualification of Journeyman Painters for Application of Coatings to Concrete Surfaces of Safety-Related Areas in Nuclear Facilities
• ASTM D4228 : EN-Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces
• ASTM D4229 : EN-STANDARD PRACTICE FOR CONDUCTING STATIC ACUTE TOXICITY TESTS ON WASTEWATERS WITH DAPHNIA
• ASTM D4230 : EN-Standard Test Method of Measuring Humidity with Cooled-Surface Condensation (Dew-Point) Hygrometer
• ASTM D4231 : EN-Standard Practice for Evaluation of Launderable Woven Dress Shirts and Sports Shirts
• ASTM D4232 : EN-Standard Performance Specification for Men´s and Women´s Dress and Vocational Career Apparel Fabrics
• ASTM D4232 REV A : EN-Standard Performance Specification for Men´s and Women´s Dress and Vocational Career Apparel Fabrics
• ASTM D4233 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN´S AND GIRLS´ KNITTED AND WOVEN BRASSIERE FABRICS
• ASTM D4234 : EN-Standard Performance Specification for Women´s and Girls´ Knitted Robe Negligee Nightgown Pajama Slip and Lingerie Fabrics
• ASTM D4235 : EN-STANDARD PERFORMANCE SPECIFICATION FOR WOMEN´S AND GIRLS´ KNITTED BLOUSE AND DRESS FABRICS
• ASTM D4236 : EN-STANDARD PRACTICE FOR LABELING ART MATERIALS FOR CHRONIC HEALTH HAZARDS
• ASTM D4236 REV A : EN-STANDARD PRACTICE FOR LABELING ART MATERIALS FOR CHRONIC HEALTH HAZARDS
• ASTM D4237 : EN-STANDARD METHODS OF TESTING RUBBER HOSE USED FOR STEAM APPLICATIONS
• ASTM D4238 : EN-Standard Test Method for Electrostatic Propensity of Textiles
• ASTM D4239 : EN-Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High- Temperature Tube Furnace Combustion Methods
• ASTM D4239 REV A : EN-Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High- Temperature Tube Furnace Combustion Methods
• ASTM D4240 : EN-Standard Test Method for Airborne Asbestos Concentration in Workplace Atmosphere
• ASTM D4241 : EN-Standard Practice for Design of Gas Turbine Generator Lubricating Oil Systems
• ASTM D4242 : EN-Standard Test Method for Glass Plate Flow for Thermosetting Coating Powders
• ASTM D4243 : EN-Standard Test Method for Measurement of Average Viscometric Degree of Polymerization of New and Aged Electrical Papers and Boards
• ASTM D4244 : EN-Standard Specification for General-Purpose Heavy-Duty and Extra-Heavy-Duty Acrylonitrile-Butadiene/Poly(Vinyl Chloride) (NBR/PVC) Jackets for Wire and Cable
• ASTM D4245 : EN-Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation for Wire and Cable 90 Degrees C Dry/75 Degrees C Wet Operation
• ASTM D4246 : EN-STANDARD SPECIFICATION FOR OZONE-RESISTANT THERMOPLASTIC ELASTOMER INSULATION FOR WIRE AND CABLE 90 DEGREES CELSIUS OPERATION
• ASTM D4247 : EN-Standard Specification for General-Purpose Black Heavy-Duty and Black Extra-Heavy-Duty Polychloroprene Jackets for Wire and Cable
• ASTM D4248 : EN-STANDARD PRACTICE FOR DESIGN OF STEAM TURBINE GENERATOR OIL SYSTEMS
• ASTM D4249 : EN-Standard Test Method for Enumeration of Candida albicans in Water
• ASTM D425 : EN-Standard Test Method for Centrifuge Moisture Equivalent of Soils
• ASTM D4250 : EN-STANDARD TEST METHOD FOR WATER-HOLDING CAPACITY OF BIBULOUS FIBROUS PRODUCTS (R 1988)
• ASTM D4251 : EN-STANDARD TEST METHOD FOR SYNTHETIC ANIONIC ACTIVE MATTER IN DETERGENTS BY POTENTIOMETRIC TITRATION
• ASTM D4252 : EN-Standard Test Methods for Chemical Analysis of Alcohol Ethoxylates and Alkylphenol Ethoxylates
• ASTM D4253 : EN-STANDARD TEST METHOD FOR MAXIMUM INDEX DENSITY AND UNIT WEIGHT OF SOILS USING A VIBRATORY TABLE
• ASTM D4254 : EN-Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
• ASTM D4255 : EN-STANDARD GUIDE FOR TESTING INPLANE SHEAR PROPERTIES OF COMPOSITE LAMINATES
• ASTM D4255/D4255M : EN-Standard Guide for Testing Inplane Shear Properties of Composite Laminates
• ASTM D4256 : EN-STANDARD TEST METHOD FOR DETERMINATION OF THE DECONTAMINABILITY OF COATINGS USED IN LIGHT- WATER NUCLEAR POWER PLANTS
• ASTM D4257 : EN-STANDARD PRACTICE FOR DESIGN AND USE OF SAFETY ALERT SYSTEM FOR HAZARDOUS WORK LOCATIONS IN THE COATINGS AND LINING INDUSTRY
• ASTM D4258 : EN-Standard Practice for Surface Cleaning Concrete for Coating
• ASTM D4259 : EN-STANDARD PRACTICE FOR ABRADING CONCRETE
• ASTM D4260 : EN-Standard Practice for Acid Etching Concrete
• ASTM D4261 : EN-Standard Practice for Surface Cleaning Concrete Masonry Units for Coating
• ASTM D4262 : EN-Standard Test Method for pH of Chemically Cleaned or Etched Concrete Surfaces
• ASTM D4263 : EN-Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method
• ASTM D4264 : EN-STANDARD METHOD FOR PRESSURE TESTING OF ASSEMBLIES OF RUBBER- LINED FIRE HOSE AND RUBBER BOOSTER HOSE IN SERVICE ON INTERIOR STANDPIPES
• ASTM D4265 : EN-Standard Guide for Evaluating Stain Removal Performance in Home Laundering
• ASTM D4266 : EN-Standard Test Methods for Precoat Capacity of Powdered Ion-Exchange Resins
• ASTM D4267 : EN-STANDARD SPECIFICATION FOR LABELS FOR SMALL- VOLUME (LESS THAN 100 mL) PARENTERAL DRUG CONTAINERS
• ASTM D4268 : EN-Standard Test Methods for Testing Fiber Ropes
• ASTM D4269 : EN-STANDARD TEST METHOD FOR SHORN PILE MASS OF FINISHED TUFTED PILE YARN FLOOR COVERING
• ASTM D427 : EN-Standard Test Method for Shrinkage Factors of Soils by the Mercury Method
• ASTM D4270 : EN-STANDARD GUIDE FOR USING EXISTING PRACTICES IN DEVELOPING AND WRITING TEST METHODS (DISCONTINUED)
• ASTM D4271 : EN-STANDARD PRACTICE FOR WRITING STATEMENTS ON SAMPLING IN TEST METHODS FOR TEXTILES
• ASTM D4272 : EN-Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
• ASTM D4272 REV A : EN-Standard Test Method for Total Energy Impact of Plastic Films By Dart Drop
• ASTM D4273 : EN-Standard Test Methods for Polyurethane Raw Materials: Determination of Primary Hydroxyl Content of Polyether Polyols
• ASTM D4274 : EN-Standard Test Methods for Testing Polyurethane Raw Materials: Determination of Hydroxyl Numbers of Polyols
• ASTM D4275 : EN-Standard Test Method for Determination of Butylated Hydroxy Toluene (BHT) in Polymers of Ethylene and Ethylene – Vinyl Acetate (EVA) Copolymers by Gas Chromatography
• ASTM D4276 : EN-Standard Practice for Confined Area Entry
• ASTM D4277 : EN-Standard Guide for Testing Amino Resins
• ASTM D4278 : EN-Standard Test Method for Wet Ashing Procedure for Preparing Wood Samples for Inorganic Chemical Analysis
• ASTM D4279 : EN-Standard Test Methods for Water Vapor Transmission of Shipping Containers- Constant and Cycle Methods
• ASTM D4280 : EN-STANDARD SPECIFICATION FOR EXTENDED LIFE TYPE NONPLOWABLE PRISMATIC RAISED RETROREFLECTIVE PAVEMENT MARKERS
• ASTM D4280 REV A : EN-STANDARD SPECIFICATION FOR EXTENDED LIFE TYPE NONPLOWABLE PRISMATIC RAISED RETROREFLECTIVE PAVEMENT MARKERS
• ASTM D4281 : EN-STANDARD TEST METHOD FOR OIL AND GREASE (FLUOROCARBON EXTRACTABLE SUBSTANCES) BY GRAVIMETRIC DETERMINATION
• ASTM D4282 : EN-STANDARD TEST METHOD FOR DETERMINATION OF FREE CYANIDE IN WATER AND WASTEWATER BY MICRODIFFUSION
• ASTM D4283 : EN-Standard Test Method for Viscosity of Silicone Fluids
• ASTM D4284 : EN-STANDARD TEST METHOD FOR DETERMINING PORE VOLUME DISTRIBUTION OF CATALYSTS BY MERCURY INTRUSION POROSIMETRY
• ASTM D4285 : EN-Standard Test Method for Indicating Oil or Water in Compressed Air
• ASTM D4286 : EN-Standard Practice for Determining Coating Contractor Qualifications for Nuclear Powered Electric Generation Facilities
• ASTM D4287 : EN-STANDARD TEST METHOD FOR DETERMINATION OF VISCOSITY OF PAINTS AND VARNISHES AT A HIGH RATE OF SHEAR BY THE ICI CONE/PLATE VISCOMETER
• ASTM D4288 : EN-Standard Specification for Calcium Borosilicate Pigments
• ASTM D4289 : EN-Standard Test Method for Elastomer Compatibility of Lubricating Greases and Fluids
• ASTM D429 : EN-Standard Test Methods for Rubber Property – Adhesion to Rigid Substrates
• ASTM D429 REV A : EN-Standard Test Methods for Rubber Property-Adhesion to Rigid Substrates
• ASTM D4290 : EN-Standard Test Method for Determining the Leakage Tendencies of Automotive Wheel Bearing Grease Under Accelerated Conditions
• ASTM D4291 : EN-Standard Test Method for Trace Ethylene Glycol in Used Engine Oil
• ASTM D4292 : EN-Standard Test Method for Determination of Vibrated Bulk Density of Calcined Petroleum Coke
• ASTM D4293 : EN-Standard Specification for Phosphate Ester Based Fluids for Turbine Lubrication
• ASTM D4294 : EN-STANDARD TEST METHOD FOR SULFUR IN PETROLEUM PRODUCTS BY NON- DISPERSIVE X-RAY FLUORESCENCE SPECTROMETRY (E1-1986)
• ASTM D4294 REV A : EN-Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
• ASTM D4295 : EN-STANDARD CLASSIFICATION FOR RUBBER COMPOUNDING MATERIALS – ZINC OXIDE
• ASTM D4296 : EN-Standard Practice for Sampling Pitch
• ASTM D4297 : EN-Standard Practice for Sampling and Handling Bisphenol A (44′-Isopropylidinediphenol)
• ASTM D4298 : EN-Standard Guide for Intercomparing Permeation Tubes to Establish Traceability
• ASTM D4299 : EN-STANDARD TEST METHODS FOR EFFECT OF BACTERIAL CONTAMINATION ON PERMANENCE OF ADHESIVE PREPARATIONS AND ADHESIVES FILMS
• ASTM D43 : EN-STANDARD SPECIFICATION FOR CREOSOTE PRIMER USED IN ROOFING DAMPPROOFING AND WATERPROOFING (AASHTO M 121) (R 1988)
• ASTM D430 : EN-Standard Test Methods for Rubber Deterioration – Dynamic Fatigue
• ASTM D4300 : EN-Standard Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi
• ASTM D4300 REV A : EN-Standard Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi
• ASTM D4301 : EN-Standard Test Method for Total Chlorine in Epoxy Resins and Compounds
• ASTM D4302 : EN-STANDARD SPECIFICATION FOR ARTISTS’ OIL AND ARTISTS’ ACRYLIC EMULSION PAINTS
• ASTM D4302 REV A : EN-STANDARD SPECIFICATION FOR ARTISTS’ OIL RESIN-OIL AND ALKYD PAINTS
• ASTM D4303 : EN-Standard Test Methods for Lightfastness of Pigments Used in Artists’ Paints
• ASTM D4303 REV A : EN-Standard Test Methods for Lightfastness of Pigments Used in Artists’ Paints
• ASTM D4304 : EN-Standard Specification for Mineral Lubricating Oil Used in Steam or Gas Turbines
• ASTM D4304 REV A : EN-Standard Specification for Mineral Lubricating Oil Used in Steam or Gas Turbines
• ASTM D4305 : EN-STANDARD TEST METHOD FOR FILTER FLOW OF AVIATION FUELS AT LOW TEMPERATURES
• ASTM D4305 REV A : EN-Standard Test Method for Filter Flow of Aviation Fuels at Low Temperatures
• ASTM D4306 : EN-Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
• ASTM D4307 : EN-Standard Practice for Preparation of Liquid Blends for Use as Analytical Standards
• ASTM D4308 : EN-STANDARD TEST METHOD FOR ELECTRICAL CONDUCTIVITY OF LIQUID HYDROCARBONS BY PRECISION METER
• ASTM D4309 : EN-Standard Practice for Sample Digestion Using Closed Vessel Microwave Heating Technique for the Determination of Total Metals in Water
• ASTM D431 : EN-STANDARD TEST METHOD FOR DESIGNATING THE SIZE OF COAL FROM ITS SIEVE ANALYSIS
• ASTM D4310 : EN-STANDARD TEST METHOD FOR DETERMINATION OF THE SLUDGING TENDENCIES OF INHIBITED MINERAL OILS (R 1991)
• ASTM D4310 REV A : EN-STANDARD TEST METHOD FOR DETERMINATION OF THE SLUDGING AND CORROSION TENDENCIES OF INHIBITED MINERAL OILS
• ASTM D4310 REV B : EN-Standard Test Method for Determination of the Sludging and Corrosion Tendencies of Inhibited Mineral Oils
• ASTM D4311 : EN-Standard Practice for Determining Asphalt Volume Correction to a Base Temperature
• ASTM D4311/D4311M : EN-Standard Practice for Determining Asphalt Volume Correction to a Base Temperature
• ASTM D4312 : EN-STANDARD TEST METHOD FOR TOLUENE-INSOLUBLE (TI) CONTENT OF TAR AND PITCH (SHORT METHOD)
• ASTM D4312 REV A : EN-Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch (Short Method)
• ASTM D4313 : EN-Standard Specification for General-Purpose Heavy-Duty and Extra-Heavy-Duty Crosslinked Chlorinated Polyethylene Jackets for Wire and Cable-Replaces ASTM D4089-82 D4090-82 and D4091-82
• ASTM D4314 : EN-STANDARD SPECIFICATION FOR GENERAL-PURPOSE HEAVY-DUTY AND EXTRA-HEAVY-DUTY CROSSLINKED CHLOROSULFONATED POLYETHYLENE JACKETS FOR WIRE AND CABLE
• ASTM D4315 : EN-STANDARD TEST METHODS FOR RUBBER COMPOUNDING MATERIAL – ZINC OXIDE
• ASTM D4316 : EN-STANDARD SPECIFICATION FOR RUBBER WATER BOTTLES (E1-1989) (R 1989)
• ASTM D4317 : EN-Standard Specification for Polyvinyl Acetate-Based Emulsion Adhesives
• ASTM D4318 : EN-Standard Test Methods for Liquid Limit Plastic Limit and Plasticity Index of Soils
• ASTM D4318 REV A : EN-Standard Test Method for Liquid Limit Plastic Limit and Plasticity Index of Soils
• ASTM D4319 : EN-Standard Test Method for Distribution Ratios by the Short-Term Batch Method
• ASTM D4320 : EN-Standard Practice for Laboratory Preparation of Chemically Grouted Soil Specimens for Obtaining Design Strength Parameters
• ASTM D4320/D4320M : EN-Standard Practice for Laboratory Preparation of Chemically Grouted Soil Specimens for Obtaining Engineering Parameters
• ASTM D4321 : EN-Standard Test Method for Package Yield of Plastic Film
• ASTM D4322 : EN-Standard Test Method for Residual Acrylonitrile Monomer Styrene- Acrylonitrile Copolymers and Nitrile Rubber by Headspace Gas Chromatography
• ASTM D4323 : EN-Standard Test Method for Hydrogen Sulfide in the Atmosphere by Rate of Change of Reflectance
• ASTM D4324 : EN-STANDARD TEST METHOD FOR CARBON BLACK PELLETED – PELLET ATTRITION
• ASTM D4324 REV A : EN-STANDARD TEST METHOD FOR CARBON BLACK PELLETED – PELLET ATTRITION
• ASTM D4324 REV B : EN-Standard Test Method for Carbon Black Pelleted – Pellet Attrition
• ASTM D4325 : EN-Standard Test Methods for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes
• ASTM D4326 : EN-Standard Test Method for Major and Minor Elements in Coal and Coke Ash by X-Ray Fluorescence
• ASTM D4327 : EN-Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography
• ASTM D4328 : EN-STANDARD PRACTICE FOR CALCULATION OF SUPERSATURATION OF BARIUM SULFATE STRONTIUM SULFATE AND CALCIUM SULFATE DIHYDRATE (GYPSUM) IN BRACKISH WATER SEAWATER AND BRINES
• ASTM D4329 : EN-Standard Practice for Fluorescent UV Exposure of Plastics
• ASTM D4330 : EN-Standard Practice for Evaluation of Fiberglass Boat Polish and Wax
• ASTM D4331 : EN-TEST METHOD FOR EFFECTIVENESS OF DEDUSTING AGENTS FOR POWDERED CHEMICALS
• ASTM D4332 : EN-Standard Practice for Conditioning Containers Packages or Packaging Components for Testing
• ASTM D4333 : EN-Standard Test Method for the Compatibility of Mechanical Pump Dispenser Components
• ASTM D4334 : EN-Standard Test Method for the Determination of the Dip Tube Retention of a Mechanical Pump Dispenser
• ASTM D4335 : EN-Standard Test Method for the Determination of the Component Retention of a Mechanical Pump Dispenser
• ASTM D4336 : EN-Standard Test Methods for Determination of the Output per Stroke of a Mechanical Pump Dispenser
• ASTM D4337 : EN-Standard Test Methods for Analysis of Linear Detergent Alkylates
• ASTM D4337 REV A : EN-STANDARD METHODS FOR ANALYSIS OF LINEAR DETERGENT ALKYLATES
• ASTM D4338 : EN-Standard Test Method for Flexibility Determination of Supported Adhesive Films by Mandrel Bend
• ASTM D4339 : EN-STANDARD TEST METHOD FOR DETERMINATION OF THE ODOR OF ADHESIVES
• ASTM D434 : EN-Standard Test Method for Resistance to Slippage of Yarns in Woven Fabrics Using a Standard Seam
• ASTM D4340 : EN-Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions
• ASTM D4341 : EN-STANDARD TEST METHOD FOR CREEP OF CYLINDRICAL HARD ROCK CORE SPECIMENS IN UNIAXIAL COMPRESSION (R 1989) (E1 1989) (E2 1991)
• ASTM D4342 : EN-Standard Practice for Collecting of Benthic Macroinvertebrates with Ponar Grab Sampler
• ASTM D4343 : EN-Standard Practice for Collecting Benthic Macroinvertebrates with Ekman Grab Sampler
• ASTM D4344 : EN-Standard Practice for Collecting Benthic-Macroinvertebrates with Smith-McIntyre Grab Sampler
• ASTM D4345 : EN-Standard Practice for Collecting Benthic Macroinvertebrates with Van Veen Grab Sampler
• ASTM D4346 : EN-Standard Practice for Collecting Benthic Macroinvertebrates with Okean 50 Grab Sampler
• ASTM D4347 : EN-Standard Practice for Collecting Benthic Macroinvertebrates with Shipek (Scoop) Grab Sampler
• ASTM D4348 : EN-Standard Practice for Collecting Benthic Macroinvertebrates with Holme (Scoop) Grab Sampler
• ASTM D4349 : EN-Classification System for Polyphenylene Ether (PPE) Materials
• ASTM D4350 : EN-STANDARD TEST METHOD FOR CORROSIVITY INDEX OF PLASTICS AND FILLERS (R 1990)
• ASTM D4351 : EN-STANDARD TEST METHOD FOR MEASURING THE THERMAL CONDUCTIVITY OF PLASTICS BY THE EVAPORATION-CALORIMETRIC METHOD
• ASTM D4352 : EN-Standard Test Method for Determination of Magnetic Material Impurities in Electrical Grade Magnesium Oxide
• ASTM D4353 : EN-Standard Test Method for Basic Stability of a Mechanical Pump Dispenser and Product
• ASTM D4354 : EN-Standard Practice for Sampling of Geosynthetics for Testing
• ASTM D4355 : EN-STANDARD TEST METHOD FOR DETERIORATION OF GEOTEXTILES FROM EXPOSURE TO ULTRAVIOLET LIGHT AND WATER (XENON- ARC TYPE APPARATUS)
• ASTM D4356 : EN-Standard Practice for Establishing Consistent Test Method Tolerances
• ASTM D4357 : EN-Standard Specification for Plastic Laminates Made from Woven-Roving and Woven-Yarn Glass Fabrics
• ASTM D4358 : EN-Standard Test Method for Lead and Chromium in Air Particulate Filter Samples of Lead Chromate Type Pigment Dusts by Atomic Absorption Spectroscopy
• ASTM D4359 : EN-Standard Test Method for Determining Whether a Material is a Liquid or a Solid
• ASTM D4360 : EN-STANDARD SPECIFICATION FOR METHYL N-AMYL KETONE
• ASTM D4361 : EN-Standard Test Method for Apparent Tack of Printing Inks and Vehicles by a Three-Roller Tackmeter
• ASTM D4362 : EN-Standard Specification for Propane Thermophysical Property Tables
• ASTM D4363 : EN-Standard Specification for Thermoplastic Chlorinated Polyethylene (CM) Jacket for Wire and Cable
• ASTM D4364 : EN-Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight
• ASTM D4365 : EN-Standard Test Method for Determining Micropore Volume and Zeolite Area of a Catalyst
• ASTM D4366 : EN-STANDARD TEST METHODS FOR HARDNESS OF ORGANIC COATINGS BY PENDULUM DAMPING TESTS
• ASTM D4367 : EN-Standard Test Method for Benzene in Hydrocarbon Solvents by Gas Chromatography
• ASTM D4367 REV A : EN-Standard Test Method for Benzene in Hydrocarbon Solvents by Gas Chromatography
• ASTM D4368 : EN-Standard Guide for Testing Poly(Vinyl Chloride) Resins
• ASTM D4369 : EN-STANDARD SPECIFICATION FOR BOXED FACIAL TISSUE INDUSTRIAL AND INSTITUTIONAL
• ASTM D4370 : EN-Standard Test Methods for Acid and Base Milliequivalent Content of Electrocoat Bath
• ASTM D4371 : EN-Standard Test Method for Determining the Washability Characteristics of Coal
• ASTM D4372 : EN-Standard Specification for Flame-Resistant Materials Used in Camping Tentage
• ASTM D4373 : EN-Standard Test Method for Calcium Carbonate Content of Soils
• ASTM D4374 : EN-STANDARD TEST METHODS FOR CYANIDE IN WATER – AUTOMATED METHODS FOR TOTAL CYANIDE AND ACID DISSOCIABLE CYANIDE
• ASTM D4375 : EN-STANDARD PRACTICE FOR BASIC DEFINITIONS NOTATION AND SYMBOLOGY FOR STATISTICS IN COMMITTEE D-19 ON WATER
• ASTM D4376 : EN-Standard Specification for Vapor-Degreasing Grade Perchloroethylene
• ASTM D4377 : EN-STANDARD TEST METHOD FOR WATER IN CRUDE OILS (KARL FISCHER) TITRATION
• ASTM D4377 REV A : EN-Standard Test Method for Water in Crude Oils by Potentiometric Karl Fischer Titration-API Designation: MPMS (Chapter 10.7); IP Designation: 356/93
• ASTM D4378 : EN-Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam and Gas Turbines
• ASTM D4378 REV A : EN-STANDARD PRACTICE FOR IN-SERVICE MONITORING OF MINERAL TURBINE OILS FOR STEAM AND GAS TURBINES
• ASTM D4379 : EN-STANDARD TEST METHOD FOR EMULSIFIED ASPHALT/JOB AGGREGATE COLD MIX TEST
• ASTM D4380 : EN-Standard Test Method for Density of Bentonitic Slurries
• ASTM D4381 : EN-Standard Test Method for Sand Content by Volume of Bentonitic Slurries
• ASTM D4382 : EN-Standard Test Method for Barium in Water Atomic Absorption Spectrophotometry Graphite Furnace
• ASTM D4383 : EN-STANDARD SPECIFICATION FOR PLOWABLE RAISED PRISMATIC REFLECTIVE PAVEMENT MARKERS
• ASTM D4384 : EN-Standard Test Method for Residual Acrylonitrile Monomer in Styrene- Acrylonitrile Copolymers and Nitrile Rubber by Solution Injection Gas Chromatography
• ASTM D4385 : EN-Standard Practice for Classifying Visual Defects in Thermosetting Reinforced Plastic Pultruded Products
• ASTM D4385 REV A : EN-STANDARD PRACTICE FOR CLASSIFYING VISUAL DEFECTS IN THERMOSETTING REINFORCED PLASTIC PULTRUDED PRODUCTS (R 1988)
• ASTM D4386 : EN-STANDARD PRACTICE FOR APPLICATION OF FLOOR POLISHES TO MAINTAIN MULTILAYER COMPOSITE TILE OR FLOORING
• ASTM D4387 : EN-Standard Guide for Selecting Grab Sampling Devices for Collecting Benthic Macroinvertebrates
• ASTM D4388 : EN-Standard Specification for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes
• ASTM D4389 : EN-STANDARD SPECIFICATION FOR FINISHED GLASS FABRICS WOVEN FROM ROVINGS
• ASTM D439 : EN-STANDARD SPECIFICATION FOR AUTOMOTIVE GASOLINE
• ASTM D439 REV A : EN-STANDARD SPECIFICATION FOR AUTOMOTIVE GASOLINE
• ASTM D439 REV B : EN-STANDARD SPECIFICATION FOR AUTOMOTIVE GASOLINE
• ASTM D4390 : EN-STANDARD PRACTICE FOR EVALUATION OF THE PERFORMANCE OF TERRY BATHROOM PRODUCTS FOR HOUSEHOLD USE (R 1993) (E1-1993)
• ASTM D4391 : EN-STANDARD TERMINOLOGY RELATING TO THE BURNING BEHAVIOR OF TEXTILES
• ASTM D4391 REV A : EN-Standard Terminology Relating to the Burning Behavior of Textiles
• ASTM D4392 : EN-STANDARD TERMINOLOGY FOR STATISTICALLY RELATED TERMS
• ASTM D4393 : EN-STANDARD TEST METHOD FOR STRAP PEEL ADHESION OF REINFORCING CORDS OR FABRICS TO RUBBER COMPOUNDS (R 1994) (E1-1994)
• ASTM D4393/D4393M : EN-Standard Test Method for Strap Peel Adhesion of Reinforcing Cords or Fabrics to Rubber Compounds
• ASTM D4394 : EN-Standard Test Method for Determining In Situ Modulus of Deformation of Rock Mass Using Rigid Plate Loading Method
• ASTM D4395 : EN-Standard Test Method for Determining In Situ Modulus of Deformation of Rock Mass Using Flexible Plate Loading Method
• ASTM D4396 : EN-Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fillings Used in Nonpressure Applications
• ASTM D4396 REV A : EN-Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications
• ASTM D4397 : EN-Standard Specification for Polyethylene Sheeting for Construction Industrial and Agricultural Applications
• ASTM D4398 : EN-STANDARD TEST METHOD FOR DETERMINING THE CHEMICAL RESISTANCE OF FIBERGLASS-REINFORCED THERMOSETTING RESINS BY ONE-SIDE PANEL EXPOSURE
• ASTM D4399 : EN-Standard Test Method for Measuring Electrical Conductivity of Electrocoat Baths
• ASTM D4399 REV A : EN-STANDARD METHOD FOR MEASURING ELECTRICAL CONDUCTIVITY OF ELECTROCOAT BATHS
• ASTM D440 : EN-Standard Test Method of Drop Shatter Test for Coal
• ASTM D4400 : EN-STANDARD TEST METHODS FOR SAG RESISTANCE OF PAINTS USING A MULTINOTCH APPLICATOR
• ASTM D4400 REV A : EN-Standard Test Method for Sag Resistance of Paints Using a Multinotch Applicator
• ASTM D4401 : EN-Standard Practice for Collecting Benthic Macroinvertebrates with Petersen Grab Sampler
• ASTM D4402 : EN-STANDARD METHOD FOR VISCOSITY DETERMINATIONS OF UNFILLED ASPHALTS USING THE BROOKFIELD THERMOSEL APPARATUS
• ASTM D4403 : EN-Standard Practice for Extensometers Used in Rock
• ASTM D4404 : EN-Standard Test Method for Determination of Pore Volume and Pore Volume Distribution of Soil and Rock by Mercury Intrusion Porosimetry
• ASTM D4405 : EN-Standard Test Method for Creep of Soft Rock Core Specimens in Uniaxial Compression at Ambient or Elevated Temperature
• ASTM D4406 : EN-Standard Test Method for Creep of Rock Core Specimens in Triaxial Compression at Ambient or Elevated Tempertures
• ASTM D4407 : EN-Standard Practice for Collecting Benthic Macroinvertebrates with Orange Peel Grab Sampler
• ASTM D4408 : EN-STANDARD PRACTICE FOR OPEN CHANNEL FLOW MEASUREMENT BY ACOUSTIC MEANS
• ASTM D4409 : EN-STANDARD TEST METHOD FOR VELOCITY MEASUREMENTS OF WATER IN OPEN CHANNELS WITH ROTATING ELEMENT CURRENT METERS
• ASTM D441 : EN-Standard Test Method of Tumbler Test for Coal
• ASTM D4410 : EN-TERMINOLOGY FOR FLUVIAL SEDIMENT
• ASTM D4410 REV A : EN-TERMINOLOGY FOR FLUVIAL SEDIMENT
• ASTM D4411 : EN-Standard Guide for Sampling Fluvial Sediment in Motion
• ASTM D4412 : EN-Standard Test Methods for Sulfate-Reducing Bacteria in Water and Water-Formed Deposits
• ASTM D4413 : EN-Standard Test Method for Determination of Ethylene Oxide in Workplace Atmospheres (Charcoal Tube Methodology)
• ASTM D4414 : EN-STANDARD PRACTICE FOR MEASUREMENT OF WET FILM THICKNESS BY NOTCH GAGES (E1-1990) (R 1990)
• ASTM D4415 : EN-Standard Test Methods for Determination of Dimer in Acrylic Acid
• ASTM D4416 : EN-Standard Specification for Acrylic Acid
• ASTM D4417 : EN-Standard Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
• ASTM D4418 : EN-Standard Practice for Receipt Storage and Handling of Fuels for Gas Turbines
• ASTM D4419 : EN-STANDARD TEST METHOD FOR MEASUREMENT OF TRANSITION TEMPERATURES OF PETROLEUM WAXES BY DIFFERENTIAL SCANNING CALORIMETRY
• ASTM D4420 : EN-Standard Test Method for Determination of Aromatics in Finished Gasoline by Gas Chromatography
• ASTM D4421 : EN-STANDARD TEST METHOD FOR VOLATILE MATTER IN PETROLEUM COKE
• ASTM D4422 : EN-STANDARD TEST METHOD FOR ASH IN THE ANALYSIS OF PETROLEUM COKE
• ASTM D4423 : EN-Standard Test Method for Determination of Carbonyls in C4 Hydrocarbons
• ASTM D4424 : EN-Standard Test Method for Butylene Analysis by Gas Chromatography
• ASTM D4425 : EN-Standard Test Method for Oil Separation from Lubricating Grease by Centrifuging (Koppers Method)
• ASTM D4426 : EN-Standard Test Method for Determination of Percent Nonvolatile Content of Liquid Phenolic Resins Used for Wood Laminating
• ASTM D4426 REV A : EN-STANDARD TEST METHOD FOR DETERMINATION OF PERCENT NONVOLATILE CONTENT OF LIQUID PHENOLIC RESINS USED FOR WOOD LAMINATING
• ASTM D4427 : EN-STANDARD CLASSIFICATION OF PEAT SAMPLES BY LABORATORY TESTING
• ASTM D4428/D4428M : EN-Standard Test Methods for Crosshole Seismic Testing
• ASTM D4429 : EN-Standard Test Method for CBR (California Bearing Ratio) of Soils in Place-(Discountinued 2002; No Replacement)
• ASTM D4429 REV A : EN-Standard Test Method for CBR (California Bearing Ratio) of Soils in Place
• ASTM D4430 : EN-Standard Practice for Determining the Operational Comparability of Meteorological Measurements
• ASTM D4431 : EN-Standard Specification for Paper Towels for Industrial and Institutional Use
• ASTM D4431 REV A : EN-STANDARD SPECIFICATION FOR PAPER TOWELS FOR INDUSTRIAL AND INSTITUTIONAL USE
• ASTM D4432 : EN-Standard Guide for Purchasing Papers Used in Continuous Computer Forms
• ASTM D4432 REV A : EN-STANDARD SPECIFICATION FOR PAPERS USED IN CONTINUOUS COMPUTER PRINTOUT FORMS (R 1989)
• ASTM D4433 : EN-Standard Specification for Flame-Resistant Treated Paper and Paperboard
• ASTM D4434 : EN-Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
• ASTM D4434/D4434M : EN-Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
• ASTM D4435 : EN-Standard Method for Rock Bolt Anchor Pull Test
• ASTM D4436 : EN-Standard Test Method for Rock Bolt Long-Term Load Retention Test
• ASTM D4437 : EN-Standard Practice for Determining the Integrity of Field Seams Used in Joining Flexible Polymeric Sheet Geomembranes
• ASTM D4438 : EN-Standard Test Method for Particle Size Distribution of Catalytic Material by Electronic Counting
• ASTM D4439 : EN-Standard Terminology for Geosynthetics
• ASTM D4439 REV A : EN-STANDARD TERMINOLOGY FOR GEOSYNTHETICS (E1-1995)
• ASTM D444 : EN-Standard Test Methods for Chemical Analysis of Zinc Yellow Pigment (Zinc Chromate Yellow)
• ASTM D4440 : EN-Standard Practice for Rheological Measurement of Polymer Melts Using Dynamic Mechanical Procedures
• ASTM D4440 REV A : EN-Standard Practice for Rheological Measurement of Polymer Melts Using Dynamic Mechanical Procedures
• ASTM D4441 : EN-STANDARD SPECIFICATION FOR AQUEOUS DISPERSION OF POLYTETRAFLUOROETHYLENE
• ASTM D4441 REV A : EN-STANDARD SPECIFICATION FOR AQUEOUS DISPERSIONS OF POLYTETRAFLUOROETHYLENE
• ASTM D4441 REV B : EN-Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene
• ASTM D4442 : EN-Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood- Base Materials
• ASTM D4443 : EN-Standard Test Method for Determining Residual Vinyl Chloride Monomer Content in PPB Range in Vinyl Chloride Homo- and Co-Polymers by Headspace Gas Chromatography
• ASTM D4444 : EN-Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
• ASTM D4445 : EN-Standard Test Method for Fungicides for Controlling Sapstain and Mold on Unseasoned Lumber (Laboratory Method)
• ASTM D4445 REV A : EN-Standard Test Method for Fungicides for Controlling Sapstain and Mold on Unseasoned Lumber (Laboratory Method)
• ASTM D4446 : EN-Standard Test Method for Anti-Swelling Effectiveness of Water-Repellent Formulations and Differential Swelling of Untreated Wood When Exposed to Liquid Water Environments
• ASTM D4447 : EN-Standard Guide for Disposal of Laboratory Chemicals and Samples
• ASTM D4448 : EN-Standard Guide for Sampling Ground-Water Monitoring Wells
• ASTM D4448 REV A : EN-Standard Guide for Sampling Groundwater Monitoring Wells
• ASTM D4449 : EN-STANDARD METHOD FOR VISUAL EVALUATION OF GLOSS DIFFERENCES BETWEEN SURFACES OF SIMILAR APPEARANCE (E1-1986)
• ASTM D445 : EN-STANDARD TEST METHOD FOR KINEMATIC VISCOSITY OF TRANSPARENT AND OPAQUE LIQUIDS (AND THE CALCULATION OF DYNAMIC VISCOSITY) (IP:71/79)
• ASTM D4450 : EN-Standard Test Method for Analysis of Zinc Hydroxy Phosphite Pigment
• ASTM D4451 : EN-Standard Test Method for Pigment Content of Paints by Low-Temperature Ashing
• ASTM D4452 : EN-Standard Methods for X-Ray Radiography of Soil Samples
• ASTM D4453 : EN-Standard Practice for Handling of Ultra-Pure Water Samples
• ASTM D4454 : EN-Standard Test Method for Simultaneous Enumeration of Total and Respiring Bacteria in Aquatic Systems by Microscopy
• ASTM D4455 : EN-Standard Test Method for Enumeration of Aquatic Bacteria by Epifluorescence Microscopy Counting Procedure
• ASTM D4456 : EN-Standard Test Methods for Physical and Chemical Properties of Powdered Ion Exchange Resins
• ASTM D4457 : EN-Standard Test Method for Determination of Dichloromethane and 111-Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph
• ASTM D4458 : EN-Standard Test Method for Chloride Ions in Brackish Water Seawater and Brines
• ASTM D4459 : EN-Standard Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications
• ASTM D446 : EN-Standard Specifications and Operating Instructions for Glass Capillary Kinematic Viscometers-IP Designation: 71S2/95
• ASTM D446 REV A : EN-STANDARD SPECIFICATIONS AND OPERATING INSTRUCTIONS FOR GLASS CAPILLARY KINEMATIC VISCOMETERS
• ASTM D4460 : EN-Standard Practice for Calculating Precision Limits Where Values are Calculated from Other Test Methods
• ASTM D4462 : EN-Standard Specification for Zinc Hydroxy Phosphite Pigment
• ASTM D4463 : EN-STANDARD GUIDE FOR STEAM DEACTIVATION OF FRESH FLUID CRACKING CATALYSTS
• ASTM D4464 : EN-Standard Test Method for Particle Size Distribution of Catalytic Material by Laser Light Scattering
• ASTM D4465 : EN-Standard Performance Specification for Zippers for Denim Dungarees
• ASTM D4466 : EN-STANDARD TERMINOLOGY FOR MULTICOMPONENT TEXTILE FIBERS
• ASTM D4467 : EN-Standard Practice for Interlaboratory Testing of a Textile Test Method That Produces Non-Normally Distributed Data
• ASTM D4468 : EN-Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and Rateometric Colorimetry

ASTM A , ASTM B ,  ASTM C ,  ASTM D | 1 || 2 || 3 || 4 || 5 || 6 || 7 || 8 |  , ASTM E , ASTM F , ASTM G