Sample size for Chemical Test

LIST of Major testing work Scope & Sample Size required for testing [Chemical]

Abrasives (ash and acid insoluble also required)10 mL
Accelerated Gum, Air Jet, ASTM D873
- a. 4 Hours 150 mL
- b. 8 Hours 150 mL
- c. 16 Hours 150 mL
Accelerated Gum, Steam Jet, ASTM D873
- a. 4 Hours 150 mL
- b. 16 Hours 150 mL
Accelerated Stability, ASTM D2274 500 mL
Accelerated Stability, Du Pont F21 200 mL
Accelerated Stability, Nalco TF9,(90 minutes at 300F., or 24 hours at 212F.) 200 mL
Acetyl Number 100 mL
Acid Insoluble of Ash 30 mL
Acid Neutralization, HBr,(FTM Std 791b, 5108.1) 500 mL
Acid Number, Aviation Turbine Fuel,ASTM D3242 200 mL
Acid Number, semi-micro, ASTM D3339 1 mL
Acid Number, ASTM D664 50 mL
Acid or Base Number, ASTM D974 50 mL
Acid Wash Color, ASTM D848 100 mL
Acidity of Distillation Residue (distillation also required)
Active Sulfur in Cutting Fluids,ASTM D1662 (requires total sulfur) 100 g
Air Release Value (IP 313), ASTM D3427 250 mL
Alcohols and Oxygenates by Gas Chromatographic Analysis, ASTM D4815 10 mL
Aldehydes in Air or Effluent (Chromotropic acid or Bisulfite addition method – plus sampling, if required)
Alkali or Mineral Acids 125 mL
Alkalinity, Reserve, ASTM D1121 100 mL
Amperometric Determination of Mercaptan Sulfur in Aviation Turbine Oils and LPG, See “Mercaptans” and “Disulfides” for gas chromatographic,
ASTM D1323 analysis of odorant chemicals
- Aviation Turbine Oil 300 mL
- LPG (liquid Petroleum Gas)
- a. Routine 1 lb
- b. Referee 3 lb
- c. After conversion of disulfides 5 lb
Aniline or mixed Aniline Point,ASTM D611 50 mL
Aniline-Gravity Constant, MIL-J-5624H 200 mL
Anti-Icing Additive, Jet Fuel 100 mL
API Gravity, Residual Products, ASTM D287 200 mL
Apparent Viscosity, ASTM D1092 2 Kg
- a. 75 to 115 F.
- b. -20 to 75 F.
- c. -21 to -100 F.
Apparent Viscosity, Brookfield 500 mL
- a. 77 F.
- b. 0 F.
- c. -10 F., -20 F., -30 F., or -40 F.
Apparent Viscosity, Brookfield,
ASTM D2983 50 mL
Appearance, visual
Aromatics, ASTM D1319 10 mL
Arsenic Determination See Metals Determination
Ash Content, ASTM D482 25 g
Ash Content, Sulfated, ASTM D874 25 g
Spectroscopy 25 g
- a. Qualitative (solids or liquids)
- b. Quantitative (oils only)
Asphalt
- a. Extraction and recovery from
- paving by Absen Method (ASTM D1836)
- b. Including viscosity, penetration and
- ash on asphalt plus sizing of
- aggregate (AASHTO T-30)
ASTM Color, Lubricants, ASTM D1500 100 mL
Autoignition Temperature at Reduced 100 mL
or Elevated Pressure, ASTM D2883
Autoignition Temperature, ASTM D2155 100 mL 9
Autoignition Temperature, ASTM E659 100 mL 8
- Hot Flame Ignition Temperature
- only (AIT) 500.00
Bacteria and Fungus
Bacteria, Anaerobic
Ball-On-Three-Discs Test, Wear Test
For Distillate Fuels 50 mL 1
+ Parts
Base Number, Total, ASTM D2896 50 mL
Base Number, Total, ASTM D4739 50 mL
Base Number, Total, ASTM D974 50 mL
Base Number, Modified ASTM D974
Bearing Rust Test, ASTM D1743 + parts 250 g
- Alternate Method (Appendix X.2)+ parts
Benzene in Gasoline, ASTM D4420 10 mL
Benzene* and Pentane Insolubles, 200 mL
ASTM D893
- a. Without coagulant
- *Toluene will be substituted
- for Benzene
- b. With coagulant
Beryllium Determination See Metals Determination
Bituminous Emulsions, Protective 5 lb
Coatings for Metal, ASTM D1010
Bleeding Test, Grease,
Bleeding Test, Grease, ASTM D1742 400 g
- a. At 77 F.
- b. Above 77 F. and up
Boiling Point Change (Molecular Weight Determination) 125 mL
Boiling Point of Engine Anti-freeze,ASTM D1120 125 mL
Boiling Range Distribution by Gas Chromatrography, ASTM D2887 0.1 mL
Boiling Range Distribution of Gasoline and Gasoline Fractions by Gas
Chromatography, ASTM D3710 0.1 mL
Bomb Copper Corrosion, MIL-G-10924 or MIL-G-23827 50 g
Bomb Corrosion Test, MIL-G-15793 50 g
Bomb Oxidation of Grease or
Liquids, ASTM D942
- b. 400 hours 50 g
- c. 100 hours with catalyst 50 g
Borderline Pumping Temperature (BPT), 100 mL
ASTM D3829
- a. Determination of actual BPT,
- per run (3 or more are required)
- b. Determination of conformance to
- SAE J300, ASTM D3829 BOTD Test, Ball-On-Three-Discs 50 mL 1
+ Parts
Bottom Sediment and Water, BS & W,ASTM D96 or ASTM D1796 200 mL
British Air Ministry Oxidation Test,IP 48/67 500 mL
Bromine Number, Electrometric,ASTM D1159 50 mL
BT9,Corrosion, IH Method + parts 500 mL
BTU, Natural Gas 250 mL
BTU, Sulfur containing materials, 25 mL
ASTM D240 + sulfur BTU, Volatile Materials, 25 mL
ASTM D240 + sulfur Bulk Modulus,ASTM D6793
Burning Quality of Fuels and Illumination Oils, ASTM D187 2000 mL
Burning, Sustained, ASTM D4206 100 mL 1
Cadmium Determination See Metals Determination
Calcium and Barium Petroleum Sulfonates 250 g
Calcium Determination See Metals Determination
Calibration of Viscometers and other Instruments
Calorific Value, ASTM D240
- a. Natural Gas 250 mL
- b. LPG 250 mL
- c. Aviation Gasoline and Jet Fuel + sulfur 50 mL
- d. Kerosine and 50 mL
- Heavier + sulfur Carbon Residue on 10% Residuum,Ramsbottom, ASTM D524 200 mL
Carbon Residue on 10% Residuum,Conradson, ASTM D189 200 mL
Carbon Residue, Conradson, ASTM D189 25 mL
Carbon Residue, Ramsbottom, ASTM D524 25 mL
Carbon, Free (by solvent extraction) 10 mL
Carbon, Free, or graphite in grease 25 g
Carbonate, gravimetric method 1 g
Carbon-Hydrogen Ratio (ASTM E191)
- a. Gasoline, Aviation Fuels and Jet Fuels (JP-4) 25 mL
- b. Kerosine and Heavier (Jet A) 25 mL
Carbonizable Substances in Paraffin Wax, ASTM D612 50 g
Carbonizable Substances in White
Mineral Oil, ASTM D565 50 mL
Cellulose Nitrate Dilution Ratio,ASTM D1720 200 mL
Cetane Improver, ASTM D4046 100 mL
Cetane Rating of Diesel Fuel, ASTM D613 1 gal
Channel Characteristics of Gear Oil, 1 qt
FTMS 791c, 3456.2 (per test temperature) Chemical Activity on Copper of
Chloride in anti-freeze, quantitative,ASTM D3634 100 g 48.50
Chloride, Organic, UOP 395 (Sodium Biphenyl method) 100 mL
Chloride, Organic, UOP 588, mod. 100 mL
Chloride, Qualitative 10 mL
Chloride, Quantitative 10 mL
Chlorine in Cutting Fluids, Active Proposed Method 1962 ASTM Standards
(includes total chlorine) 50 mL
Chlorine in Lubricating Oil,ASTM D1317 (Sodium Alcoholate Method) 50 mL
Chlorine or Chloride, trace, bomb method 25 mL
Chlorine,Trace, Water-Leachable 100 mL
Chlorine, ASTM D808 10 mL
Chromatographic Analysis of Natural Gas 100 mL
LPG (Hydrocarbon Distribution) Chromatographic Method for Determination of Characteristic Groups in Extender and Processing Oils Clay Gel Adsorption, ASTM D2007 50 mL
Chromium Determination See Metals Determination
Clarity of Distillate Fuel ASTM D4176 1000 mL
Cleanliness Test, Particle Count, ARP 598A or ASTM F312 100 mL
- If 1-5 micron range is included
Cleanliness, Particle Weight, ASTM F313, D2276 or D5452
100 mL
- Including filtration of more than 100 mL
Cloud Point, ASTM D2500 50 mL
- a. Above 30 F.
- b. From 30 to 0 F.
- c. From 0 F. to -30 F.
- d. Below -30 F.
Cloud Intensity at Low Temp.,FTM 791c 202.1 200 mL
Coefficient of Friction (4-Ball Method) + parts 100 mL
Coefficient of Friction (Falex Method) + parts 100 mL
Coefficient of Thermal Expansion and up 50 mL
Coking Test, Panel, FTMS 791b, 3462 600 mL
- a. 600 F.
- b. 700 F.
- c. 800 F.
600 mL
Cold Cranking Simulator,Apparent Viscosity, ASTM D5293 10 mL
Color, Acid Wash, ASTM D848 100 mL
Color, Refined Oils, Saybolt
Chromometer, ASTM D156 250 mL
Combustion Additive in Diesel Fuel,VV-F-800C 25 mL
Compatibility of Lubricants, 300 mL per FTMS 791c, 3403.2 set of blends
Combustiblity, Sustained, 100 mL
UN Method L2
Conductivity, Thermal, ASTM D2717 100 mL
- a. Between 100 F. and 300 F.,
- per temperature
- b. 32 F.,
- c. Between 300 F. and 500 F.,
Cone Penetration of Lubricating Grease, ASTM D217 500 g
- a. Unworked
- b. Worked 60 strokes
- c. 1/4 Scale (ASTM D1403), unworked 5 g
- 60 strokes 5 g
Congealing Point of Pharmaceutical Petrolatum, ASTM D938 50 g
Consistency of Grease, ASTM D217 500 g
- b. Worked 60 reciprocal strokes
- c. Worked 100,000 reciprocal strokes
- d. 1/4 Scale (ASTM D1403), unworked 5 g
- e. 1/4 Scale (ASTM D1403), worked
- 60 strokes 5 g
Consistency Test (Roll Stability),ASTM D1831
- a. 2 hours @ ambient temperature
- b. 100 hours @ 150 F. 2
Copper Corrosion of LPG, ASTM D1838 100 g
Copper Corrosion of Petroleum Products,ASTM D130 (@ 122 F. or 212 F.) 50 mL
Copper Corrosion Test, ASTM D1616 and ASTM D1275 50 mL
Copper Corrosion, Grease,FTMS 791b, 5309.4 or ASTM D4048 25 g
Copper Corrosion, Grease, ASTM D1261 25 g
Copper Determination See Metals Determination
Corrosion and Rubber Swelling, Brake Fluids, + parts 350 mL
SAE J17030 plus pH Corrosion of Copper, Vapor Phase, MIL-P-46002B 1000 mL
Corrosion Preventive Properties of 1/4 lb 2 Lubricating Grease, ASTM D1743 + parts
Alternate Method (Appendix X.2) 2 + parts
Corrosion Protection,Static Water Drop 50 mL
Corrosion Protection, MIL-C-46113B + parts 250 mL
Corrosion Protection, VV-C-846a + parts 250 mL
Corrosion Protection, ASTM D1748 500 mL
- a. Panel Preparation, each
- b. Exposure and Evaluation,
- per panel, per hour
- c. Minimum Exposure Charge, per sample
Corrosion Protection, Galvanic,FTMS 791c, 5322.2 50 mL
Corrosion Resistance Of Grease, MIL-G-10924 100 g
Corrosion Test, Engine Coolant, ASTM D1384, per run 500 mL 2
Corrosion Test, International Harvester, BT-9, per run + parts 500 mL
Corrosion, Copper, Static, FTMS 791c, 5305.1 250 mL
- a. 450 F.
- b. 600 F.
Corrosion, Silver, IP 227 500 mL
Corrosion, Rust Preventing Characteristics of Turbine Oil, ASTM D665 600 mL
- a. Distilled Water (Procedure A)
- b. Synthetic Sea Water (Procedure B)
- c. Procedure C
Corrosion, Silver, Static, 250 mL
FTMS 791c, 5305.1
- a. 450 F.
- b. 600 F.
Corrosion, Vapor Phase,After Exhaustion, MIL-P-46002B 1000 mL
Corrosion, Vapor Phase,MIL-P-46002B 1000 mL
Corrosion-Oxidation Stability,MIL-L-3918 250 mL
Corrosion-Oxidation Stability,FTMS 791c, 5307.2
Corrosion-Oxidation Stability,FTMS 791c, 5308.7 250 mL
- a. 250 F. – 168 hours
- b. 347 F. – 72 hours
- c. 400 F. – 48 or 72 hours
- d. 425 F. – 48 or 72 hours
- e. 450 F. – 48 or 72 hours
- f. 500 F. – 48 or 72 hours
- g. 600 F. – 48 or 72 hours
- h. 700 F. – 48 or 72 hours
Modifications (including different Cummins Method)temperatures, longer exposures and special metals, ASTM D6594,
Sludge Included Corrosive Sulfur in Electrical Insulating Oils, ASTM D1275 300 mL
Corrosiveness of Emulsifiable Cutting Fluids, FTMS 791c, 5306.5 150 mL 1
Corrosiveness of Grease or Semi-Solid Products, FTMS 791c, 5304.5 (77 F) 25 g
Corrosiveness, Grease, Copper Strip,212 F., FTMS 791b, 5309.4 25 g
Corrosivity of LPG, ASTM D1838 150 g
Corrosivity, Galvanic Corrosion,FTMS 791c, 5322.2 50 mL
Crankcase Oil Dilution, Diesel Fuel Calculation from Viscosity Data
10 mL
Crankcase Oil Dilution, Diesel Fuel, Gas Chromatographic Method,
ASTM D3524 1 mL 2
Crankcase Oil Dilution, Gasoline,ASTM D322 50 mL
Crankcase Oil Dilution, Gasoline,ASTM D3525 1 mL 2
Cutting Oil, Soluble, 100 mL
Corrosion of Cast Iron, + cost of IP 125/77 specimens
Cutting Oil, Soluble, Oil Content,
Dispersed, IP 137/55 1000 mL
Cutting Oils, Emulsion Stability,ASTM D1479 500 mL
De-Waxing Lubricants,UOP 46-64 and up 10 g
Deleterious Particles in Grease,ASTM D1404 10 g
Demulsibility, (Viscosity may be required to determine test temperature)
ASTM D1401 100 mL
- a. 130 F.
- b. 180 F.
Demulsibility, Steam Emulsion Test,ASTM D1935 or IP 19/76, per run 100 mL
Demulsibility, Texaco SP 344-60 100 mL
Density and Specific Gravity of Solid Pitch and Asphalt, ASTM D71 50 g
Density and Specific Gravity of Liquids (by Pycnometer, ASTM D1475) 25 mL
- a. 60 F., 68 F., 77 F.
- b. 100 F., 130 F., 210 F.
Other temperatures,
- 80 F. to 700 F.
Density of Road Oils, Road Tars,Asphalt Cements, ASTM D70 50 g
Density of Volatile Liquids and Gases 250 mL
Deposit-Forming Tendencies of Aircraft Turbine Lubricants, 1 gal 3 ASTM D3711, liquid and vapor Deposition Tendency, Thin Film, ASTM D3711 200 mL
Deposition Tendency, Vapor, ASTM D3711 200 mL
Dew Point of Gas 3 cu.ft
Dew Point of LPG 3 gal
Dielectric Strength,ASTM D877 or D1816 500 mL
Diene Value, UOP 326 50 g
Differential Mackey Test, 50 g
Spontaneous Heating Value, ASTM D3523 and up
Diluted Color of Hydrocarbon Solvent, Dilution Ratio, Nitrocellulose, ASTM D1720 200 mL
Dilution, Crankcase Oil with Diesel Fuel, Calculated from Viscosity 10 mL
Dilution, Crankcase Oil with Diesel Fuel, ASTM D3524 1 mL
Dilution, Crankcase Oil with Gasoline Engine, ASTM D322 100 mL
Dilution, Crankcase Oil with Gasoline, ASTM D3525 1 mL
Dirt Count of Grease, FTMS 791b, 3005.3 25 g
Distillation of Aromatic Hydrocarbon, ASTM D850 150 mL
Distillation of Crude Petroleum, Hempel, ASTM D285 500 mL
Distillation of Crude Petroleum, Residue, IP 78/51T 200 mL 2
Distillation of Natural Gasoline, ASTM D216 150 mL
Distillation of Petroleum Products, ASTM D86 250 mL
Distillation of Plant Spray Oils,ASTM D447 150 mL
Distillation, Steam, of Bituminous
Protective Coatings, ASTM D255 1500 mL
Distillation, Vacuum, ASTM D1160 300 mL
Distillation, Vacuum, of Liquid and 300 mL
Semi-Solid Asphaltic Materials to per Obtain Residue of Specified distillation Penetration, ASTM D1189 + penetrations
Disulfides in LPG (Gas Chromatographic Method) and up 25 g
Doctor Test, ASTM D 4952 25 mL
Drop Melting Point of Wax, ASTM D3954 10 g
Dropping Point of Lubricating Grease,ASTM D566 10 g
Dryness of Propane (Cobalt Bromide Method) 3 gal
Dryness of Propane (Dew Point Method) 3 gal
Dryness of Propane (Valve Freeze Method, ASTM D2713) 3 gal
Dryness of Propane (KF Method) 100 g
Effect of Grease on Copper, ASTM D1261 50 g 67.50
Effect on Cobalt Chloride Indicating Desiccant, FTMS 791b,
- per MIL-C-6529C
Electrical Conductivity of Jet Fuel,ASTM D2624 250 mL
Elastomer Compatibility, ASTM D4289 250 g
Elemental Analysis, Carbon-Hydrogen
- a. Aviation Gasoline and Jet Fuel 20 g
- b. Kerosine and Heavier 20 g
Emission Spectrographic Analysis 1 g
- a. Qualitative (liquids or solids)
- b. Quantitative (oils only)
Emulsion Characteristics of Soluble Cutting Oils, 25 mL
FTMS 791c, Emulsion Characteristics of 100 mL
Lubricating Oil, ASTM D1401
- a. 130 F.
- b. 180 F.
Emulsion Tolerance of Grease 100 g
Emulsion, Steam, Lubricating Oils, ASTM D1935 100 mL
Endurance Life, Falex, of solid film lubricants (ASTM D2625A)
- + parts, per run (4 required), for 1 hr. or less
- /0.5 hr. for additional running time
Environmental Analysis
Environmental Exposure – also see
Humidity Test, Salt Spray Test, and Protection Tests
Evaporation Loss of Lubricating Greases and Oils, ASTM D972 and 25 mL
Modifications
- a. 22 hrs. @ 210-300 F. and 760 mm.Hg.
- b. 6 hrs. @ 400 F. and 760 mm.Hg.
- c. 6 hrs. @ 450 F. and 760 mm.Hg.
- d. 6 hrs. @ 500 F. and 760 mm.Hg.
- e. 6 hrs. @ 450 F. and 140 mm.Hg.
- f. 6 hrs. @ 500 F. and 140 mm.Hg.
- g. Other Modifications
Evaporation Rate, Gardner Method 10 mL
Evaporation of Brake Fluid, 500 mL
SAE J1703c + Pour Point
MIL-L-7808G 25 mL
Evaporation, FTMS 791c, 353.1 25 mL
Existent Gum in Fuel (ASTM D381)
- a. Air jet 200 mL
- b. Steam jet 200 mL
Explosive Vapors in Fuel,FTMS 791b, 1151.1 500 mL
Extreme Pressure Properties See Load Carrying Capacity Falex Load Carrying Capacity of + parts,Solid Films, ASTM D2625B per run (4 required)
Falex Test (E.P.), ASTM D3233A or D3233B + parts 100 mL
Falex Test (Wear), ASTM D2670 and up + parts 100 mL
Falex Wear Life of Solid Films, + parts, ASTM D2625A per run (4 required)
(See Endurance Life)
Fatty Acid Analysis of oils and fats by Gas Chromatography 50 g
Fatty Acid Separation from Grease 200 g
Fatty Oils (Fixed Oils) Separation 200 mL
Ferrous Metal Protective Characteristics of Universal Gear Lubricants in
Presence of Water, FTMS 791b, 5315.1 300 mL
FIA, Hydrocarbon Types, ASTM D1319 Fillers in Grease and up 100 g
Film Stability and Corrosion on Steel, MIL-G-27617C
Filter Color Rating, ASTM D2276 1 gal
Filtration Cleanliness, ASTM D2276 or D4898 100 mL
- Including Filtration of More Than 100 mL
Flammable Solids Classification,49CFR173, App.E Or UN Method 100 g
Flame Propagation Rate, Linear, ASTM D5306, 100 mL
Flash Point and Fire Point, 100 mL
Cleveland Open Cup, ASTM D92
- a. Flash below 200 F.
- b. Flash between 200 F. and 300 F.
- c. Flash between 300 F. and 500 F.
- d. Flash above 500 F.
Flash Point, Cleveland Open Cup, ASTM D92 100 mL
- a. Below 200 F.
- b. Between 200 F. and 300 F.
- c. Between 300 F. and 500 F.
- d. Above 500 F.
Flash Point, Pensky-Martens Closed Cup, ASTM D93 100 mL
- a. 100 F. and above
- b. Below 100 F. 40.00 and up
Flash Point, Seta Flash (determination of actual flash point), ASTM D3278 or D3828 10 mL
- a. Flash above 100 F., but less than 200 F.
- b. Flash between 85 and 100 F.
- c. Flash between 60 and 85 F.
- d. Flash below 60 F.
- e. Flash above 200 F.
Flash Point, Seta Flash (go-no-go at any fixed temperature), ASTM D3278 or D3828 5 mL
- a. Flash above 100 F., but less than 200 F.
- b. Flash between 85 to 100 F.
- c. Flash between 40 and 85 F.
- d. Flash above 200 F.
Flash Point, Tagliabue Closed Cup, ASTM D56 100 mL
- a. 100 F. and above
- b. Below 100 F. and up
Flash Point, Tagliabue Open Cup, ASTM D1310 300 mL
- a. Flash below 60 F. 2 and up
- b. Flash between 60 F. and 200 F.
- c. Flash between 200 F. and 325 F.
Flock Point of Refrigerant Compressor Oil, FTMS 791b, 1303.1 +Cost of Refrigerant 50 mL
Flow Point, O-F-506B 500 mL
Fluorine or Fluoride, standard method 1 g
Fluorine or Fluoride, trace method 1 g
Foaming Characteristics, 3 cycles ASTM D892 600 mL
- First cycle only
Free Alkali in Grease 100 g
Free and Corrosive Sulfur, ASTM D130 50 mL
Free Fatty Acids in Grease 100 g
Freezing Point of Aqueous Engine Anti-Freeze Solutions, ASTM D1177 100 mL
Freezing Point of Aviation Fuels,ASTM D2386 100 mL
Fretting Wear Protection, +parts ASTM D4170 100 g
Fuel Contamination, MIL-S-5545A 200 mL
Fuel Stripping of Used Engine Oil,ASTM D3607 100 mL
Fuel System Icing Inhibitor,FTMS 791c,5327.4 100 mL
Galvanic Corrosion, FTMS 791c, 5322.2 or ASTM D6547 50 mL
Galvanic Corrosion, Salt Spray 500 mL
Gas Bubble Separation Time,ASTM D3427 or IP 313 250 mL
Gas-Liquid Partition Chromatography,Analysis of Natural Gas 100 mL
LPG 2 Gas-Liquid Partition Chromatography,Miscellaneous Systems
- a. Gas 100 ml.
- b. Liquid 1 ml.
- c. Odorants Glycol in Used Lubricating Oil
See “Mercaptans” and “Disulfides”
- a. Qualitative 100 mL
- b. Quantitative 100 mL
GM Quenchometer 500 mL 1
Gravity, API, of Petroleum by Hydrometer, ASTM D287
- a. Distillable products 300 mL
- b. Residual products 300 mL
Gravity, Specific of Gaseous Fuels, 250 mL
-(Including BTU and Composition)
Gravity, Specific, of Industrial Aromatic Hydrocarbons, ASTM D891 50 mL
Gravity, Specific, of Miscellaneous Liquids, ASTM D1480 and ASTM D1481 50 mL
- a. At 60 F., 68 F., and 77 F.
- b. At 100 F., 130 F., and 210 F.
- c. At other temperatures,
80 F. to 700 F.
Gravity, Specific, of Road Oils, Road Tars, Cements and Soft Tar Pitches, ASTM D70 50 g
Grease Mobility @ 0 F.
(U.S. Steel Method) “See Mobility” 2 lb
Gum, Existent, in Fuel, ASTM D381 150 mL
- a. Air jet
- b. Steam jet
Gum, Potential, Air Jet Evaporation, ASTM D873 150 mL
- a. 4 hours
- b. 8 hours
- c. 16 hours
Gum, Potential, Steam Jet Evaporation, ASTM D873 150 mL
- a. 4 hours
- b. 16 hours
Halogen, Total (except Fluorine) 50 mL
- Trace (bomb method) 50 mL
Halogen, Total (Fluorine only) 50 mL
- Trace (Fluorine only) 50 mL
Hardness of Water
(Calcium and Magnesium) 10 mL
Heat of Combustion, Gross
- a. Gaseous Fuel 250 mL
- b. LPG 250 mL
- c. Liquid Fuel, ASTM D240 100 mL
Kerosine and heavier + sulfur
Gasoline and other
volatile materials + sulfur
Heat Capacity of Solids or Liquids, ASTM D2766 200 mL
- a. 100 F. to 400 F. inclusive, Liquids
- c. Other temperatures and conditions
- NOTE: Vapor pressure data may be required for samples of high volatility at test temperatures.
- Vapor Pressure by Isoteniscope, ASTM D2879-includes heat of vaporization Heat Stability of Transmission Oils (Heat Test) 500 mL
Heat Test, Static (U.S.Steel Method) 250 g
Heating, Self (Differential Mackey Test), ASTM D3523 and up 50 g
Herschel Demulsibility (Viscosity may be required to determine test temperature)200 mL
- a. At 130 F.
- b. At 180 F.
High and Low Temperature Stability,FTMS 791b, 3460 50 mL
Horizontal Disc, Rust Prevention Properties, ASTM D3603 600 mL
Hot-Wire Quench Test Humidity Corrosion Test of Grease, ASTM D1743 (100 hrs) + parts 500 g
Humidity Corrosion Test, International Harvester BT-9 + parts 500 mL
- a. Preparation of test panels, ea.
- b. Exposure, per specimen hour
- c. Minimum exposure charge, per sample
Hydrobromic Acid (HBr) Neutralization,FTMS 791b, 5108.1 500 mL
Hydrocarbon Type Identification,ASTM D1019 and ASTM D875 200 mL
Hydrocarbon Types (PONA) 200 mL
Hydrocarbon Types in Liquid Petroleum Products by Fluorescent 10 mL
Indicator Adsorption, ASTM D1319 Hydrocarbon Types in Liquid Petroleum
- (4 required), each
- (Cycle C) or
- (Extended Cycle C)
- 40 Hour Test Sequence, plus parts
- 80 Hour Test Sequence, plus parts
- a. @ 100 F.
- a. @ 77 F.
- a. 1 hour @ 325 F.
- a. 1 hour @ 325 F.
- a. 100 F.
- a. -100 F.
- a. 100 F. to 200 F., per temperature
- a. 100 F. to 400 F., inclusive, Liquids
- a. 100 hours
- a. 100 hours
- a. 100 hours 50 g
- a. 100 hrs. @ 150 F., MIL-G-10924B
- a. 158 F. to 400 F., FTMS 791c, 3603.5 and 3604.2
- a. 240 min., max.
- a. 60 F. and above
- a. 60 F. and above
- a. 600 F.
- a. 72 hours at -40 F., first sample
- a. 75 F. to 115 F. 1
- a. Above 30 F.
- a. As received, referee method 3 lb
- a. As received, referee method 3 lb
- a. Asphalts, ASTM D71, 60/60 F. 25 g
- a. At 77 F.
- a. At 77 F.
- a. Aviation Turbine Fuel 300 mL
- a. Basic Test 1
- a. Below 300 F.
- a. Below 300 F. 50 g.
- a. Chlorides (ASTM D512)
- a. Determination of Actual BPT, per run, (3 or more required)
- a. Distilled Water, Procedure A
- a. For 3 hours
- a. Light Oil
- a. Light oils or fuels(incl.non-combustibles)
- a. Liquids,ASTM D2782 1 gal 140.00 + parts
- a. Natural Gas (qualitative) 3 cu.ft
- a. Oil 140.00 + parts
- a. Other temperatures
- a. Other Temperatures
- a. Panel Preparation, each
- a. Preparation of specimens, ea. and up
- a. Qualitative (solids or liquids)
- a. Research Method, ASTM D2699 1 gal
- a. Research Method, ASTM D2699 1 gal
- a. Unworked
- a. Unworked
- a. UOP Method B
- a. Without coagulant
- a. Without coagulant
- a. Without coagulant
- Above prices for viscosity + density at test temperature
- Additional Charge For Water by GC 1
- Additional exposure, per 6 hr. period
- additional samples running at same time, each
- additional samples running at same time, each
- additional samples running at same time, each
- Aluminum
- Antimony
- Arsenic
- ASTM D1263 150 g
- ASTM D4290, plus parts 150 g
- b. @ 0 F.
- b. @ 175 F. 80.00
- b. 100 F. to 400 F. inclusive, Solids
- b. 100 F. to 400 F., inclusive, Solids
- b. 175 F.
- b. 2 hrs. at ambient temperature, ASTM D1831
- b. -20 F. to 75 F. 1
- b. 200 hours
- b. 200 hours
- b. 300 F. and above
- b. 300 F. and higher 50 g.
- b. 300 min., max.
- b. 32 F., per temperature 7
- b. 5 hours @ 375 F.
- b. 5 hours @ 375 F.
- b. 60 F. to -30 F.
- b. 60 F. to -30 F. 1
- b. -65 F.
- b. 700 F.
- b. 72 hours at -65 F., first sample 2
- b. After conversion of disulfides 5 lb
- b. After conversion of disulfides 5 lb
- b. At 100 F.
- b. At 100 F.
- b. Determination of Conformance to SAE J300 Miniaturized Corrosion and Oxidation 250 – 700 F.
- b. Exposure, per specimen/hour
- b. First specimen, per hour
- b. For 72 hours
- b. From 30 F. to -20 F.
- b. From Leachable Sodium and Chloride Ions
- b. Gaseous Fuels 60/60 F. 250 mL
- b. Grease 1 + parts
- b. Grease, ASTM D2509 5 lb 1 + parts
- b. Heavy Oil
- b. Heavy oils or oils with sludge and up
- b. In liquid and vapor phase with o-rings + parts
- b. Low Temperature Viscosity,
- b. LPG (qualitative) 500 g
- b. LPG, routine method 1 lb
- b. Motor Method, ASTM D2700 1 gal
- b. Motor Method, ASTM D2700 1 gal
- b. Nitrates (ASTM D1608)
- b. Quantitative (oils only)
- b. Synthetic Sea Water, Procedure B
- b. With coagulant
- b. With coagulant
- b. With coagulant
- b. Worked 60 reciprocal strokes
- Barium
- Beryllium
- Bismuth
- Boron
- c. -10 F., -20 F., -30 F., or -40 F., each 2
- c. 2 hour test Addt’l
- c. 200 F. to 500 F., per temperature
- c. -21 F. to -100 F. 2
- c. 360 min., max.
- c. -40 F.
- c. 400 hours 1
- c. 400 hours 1
- c. 72 hours at -80 F., first sample 2
- c. 800 F.
- c. Additional specimens, + cost
- c. Aviation Gasoline 1 gal
- c. Aviation Gasoline 1 gal
- c. Below -30 F.
- c. Below -30 F. 1
- c. Filter more than 100 mL and up
- c. From -20 F. to -50 F.
- c. LPG referee 3 lb
- c. LPG, 60/60 F. 500 g
- c. Minimum exposure charge
- c. Neutralization Numbers, if required by specification,(2 required), each (ASTM D664)Shell 4-Ball Wear Test, ASTM D2266 50 g
- c. Nitrates (APHA 418B, ASTM D992 or phenol disulfonic acid method)
- c. Other temperatures
- c. Procedure C
- c. Quantitative methylene blue Hydrolytic Stability,FTMS 791b, 3457.1, ASTM D2619 200 mL
- c. Worked 100,000 reciprocal strokes
- Cadmium
- Calcium
- Chromium
- Cobalt
- Complete, including hot-flame (AIT),cool-flame (CFT), Threshold (RTT and Reaction) Ignition Temperature, Autoignition, FTMS 791b, 5050 100 mL
- Copper
- d. 1/4 Scale (ASTM D1403) 5 g
- d. 1/4 Scale (ASTM D1403), worked
- d. 100 hours with catalyst
- d. 100 hours with catalyst
- d. -20 F.
- d. 480 min., max.
- d. Below -50 F.
- d. Fluids, 60 F., 68 F., 77 F. 25 g
- d. LPG referee, after conversion of disulfides 5 lb
- d. Storage for more than 72 hours
- d. Sulfides (APHA 4500 S-2)
- d. Synthetic Sea Water, 4%, 5% or 20%
- Disulfide determination, 25 g
- Disulfide determination, 25 g
- Disulfides Determination, 25 g
- e. 0 F.
- e. 1/4 Scale (ASTM D1403),worked 60 strokes 5 g
- e. Additional exposure Infrared Spectrophotometry, ASTM E1252 With Interpretation and up
- e. Fluids, 100 F., 130 F., 210 F. 25 g
- f. 40 C.
- f. Other Temperatures,
- g. 130 F.
- Gold and up +
- h. 100 C.
- Hot Flame Ignition Temperature only (AIT)
- i. Above 100 C. (Also See Viscosity
- if required by specification,
- Iron
- j. Odd Temperatures, 32 F. to 210 F.
- k. Odd Temperatures, 210 F. to 400 F.
- l. Reverse flow viscosity @ 40 C. or 100 C.
- Lead
- Lithium
- m. 100 F. or 210 F.
- Magnesium
- Manganese
- Mercury
- Minimum exposure charge, per sample
- Molybdenum
- n. Saybolt Viscosity @ 100 F. or 210 F.
- Nickel
- NOTE: Vapor Pressure data may be required for samples of high
- of Vulnerable Fluids) and up
- Palladium cost of Platinum standards
- per analyte and up
- per analyte and up
- per analyte and up Oil and Grease in Water(Hexane Soluble) 1 gal
- per specimen hour of electrodes
- per temperature
- Plus addt’l charge of stable emulsions for separation of Hydroxyl Number 100 mL
- Potassium
- Rare Earths
- salt solution, cabinet set-up charge
- Selenium
- Silicon
- Silver
- Sodium
- Strontium
- Thallium
- Tin
- Titanium
- Tungsten
- Vanadium
- Vapor Pressure by Isoteniscope,ASTM D2879-includes heat of vaporization 3
- volatility at test temperatures.
- With Qualitative Water Test
- Zinc
“See Corrosion-Oxidation” Mobility of Grease @ 0 F.(U.S. Steel Method) 2 lb
(O No. or R No.) each Norma-Hoffman Oxidation, ASTM D942 50 g
…Additional charge for trace analysis…
2 hour test Addt’l Silica
-80 F. to 700 F. Specific Heat of Solids and
Alkyl Lead Compounds in gasoline As Total Lead, ASTM D3237 10 mL
And up Metal Determination by Atomic Absorption or ICP analysis with organic standards in organic phases per metal and up Metals Determination by Price per Sample Atomic Absorption or ICP
Antimony Determination See Metals Determination API Gravity, Distillable Products,ASTM D287 200 mL
Apparent Viscosity by Cold Cranking Simulator, ASTM D5293 25 mL
Aromatics, ASTM D1019 and D875 250 mL
Ash, Analysis by Emission
Asphaltenes in asphalt, ASTM D3279 10 g
ASTM D2266 and ASTM D4172
ASTM D5453 25 g
Bitumen Determination, ASTM D2042 125 mL
Characteristics, ASTM D1263 200 g.
Chemical Method 20 g
Coking Test,Panel (RTD Modification of Method 3462, FTMS 791b)
Color, Petroleum Products, ASTM D1500 60 mL
Corrosion Resistance of Grease, MIL-G-15793 50 g
determinations Pressure Separation of Oil from Grease, ASTM D1742 1 lb
Diesel Index, IP 21/53 100 mL
Direct Method (by ICP) 10 g
Effluents by Gas Chromatography Hydrogen Sulfide and up
Estimation from Evaporation Rate, ASTM D2878 Molecular Weight of Petroleum Oils,
Estimation from Viscosity, ASTM D2502 25 mL
Evaporation, 6 hrs. @ 400 F.,
fractions) 100 mL
FTMS 791b, 5321.1
FTMS 791c, 321.3 100 g
Greases at Room Temperature, ASTM D1742 Separation of Saponifiable or Unsaponifiable, each Shear Stability, Sonic Shear, ASTM D2603 250 mL
Hexane Solubles in Water 1 gal
Horizontal Disc Method, ASTM D3603, per run 600 mL
Hot Surface Ignition, ASTM D6668 100 mL
Humidity Test, ASTM D1748 500 mL
Hydrocarbon Types, ASTM D2007 50 mL
Hydrocarbon Types, N-d-M Method,ASTM D3238 100 mL
Hydrocarbon Types, VGC Method,ASTM D2140 100 mL
Hydrocarbons, Total and Carbon Number Distribution, in Air or 1000 mL
Icing Inhibitor, FTMS 791c, 5327.4 Ignition Quality, Diesel Fuel,ASTM D613 1 gal
Ignition Quality, Gasoline,ASTM D2699 or D2700, each 1 gal
Ignition Temperature, Autogenous at Elevated or Reduced Pressure, ASTM D2883 100 mL
Ignition Temperature, Autoignition,ASTM D2155 100 mL 9
Ignition Temperature, Autoignition,ASTM E659 100 mL
Including change in Durometer Hardness, Elongation and Tensile Strength
Induction Period of Fuel, ASTM D525 150 mL
Inherent (Intrinsic) Viscosity of Polymers, ASTM D2857 10 g
Inorganic Fines in Marine Residual Fuel, ASTM D4484 100 mL
Insoluble Resins, Used Lubricating Oil 200 mL
Insolubles, ASTM D893 200 mL
Insolubles, Total, ASTM D2274 (Accelerated Stability) 500 mL “See Oxidation Stability”
Interfacial Tension, Oil against Water by DuNuoy Tensiometer, 77 F., ASTM D971 (plus required density determination)200 mL
Iodine Number, ASTM D1959 50 mL
Iron Determination See Metals Determination of Turbine Fuel, ASTM D3241 1 L
JFTOT Thermal and Oxidative Stability Karl Fischer Water Determination,ASTM D1364, D4377, E203 100 mL
Kauri-Butanol Solvency No.,ASTM D1133 150 mL
Kjeldahl Nitrogen, ASTM D3228 20 g
Knock Characteristics of Motor Gasoline,Motor Method, ASTM D2700 1 gal
Knock Characteristics of Motor Gasoline,Research Method, ASTM D2699 1 gal
Lead Alkyls, total in Gasoline 25 mL Lead Corrosion Test, SOD, 600 mL
Lead Determination See Metals Determination
Lead in Gasoline, ASTM D3237 10 mL
Leakage Tendency of Automobile Wheel Bearing Grease,
Life Performance of Automobile Wheel Bearing Grease, ASTM D3527 150 g
Liquid, ASTM D2766 200 mL
Load Carrying Capacity, Falex 200 mL
Load Carrying Capacity, Load Wear Index, oil. (includes no-seizure load and weld + parts point) ASTM D2596, grease; ASTM D2783, 200 mL
Load Carrying Capacity, Mean Hertz 400 mL
Load Carrying Capacity, SAE 2 + parts,per RPM
Load Carrying Capacity, Universal Gear Lubricants, Timken, FTMS 791b, 6506.1
Load, FTMS 791b, 6503.2 (4-Ball E.P.) + parts
Loss on Heating, 5 hrs. @ ASTM D6 325 F.,100 g
Low Temperature Stability, FTMS 791b, 3458 200 mL
Low Temperature Torque of Grease Lubricated Wheel Bearings, ASTM D4693 150 g
Low Temperature Torque, ASTM D1478 200 g
Mackey Test, Spontaneous Heating Value, ASTM D3523 and up 50 g
Melting Point of Grease and Petrolatum, ASTM D127 and ASTM D566 20 g
Melting Point of Paraffin Wax, ASTM D87 50 g
Mercaptan Sulfur in Aviation Turbine Fuels and LPG, Amperometric Method, ASTM D1323
Mercaptan Sulfur in Gasoline,Kerosine, Aviation Turbine and Distillate Fuels, Potentiometric Method, ASTM D3227 300 ml
Mercaptans in LPG, Gas Chromatographic Method, per analyte and up 25 g
Mercury Determination See Metals Determination Mercury Freeze Test 500 mL
Metal Content of Gas Turbine Fuel, ASTM D2788, ASTM D3605 per metal
Metal Determination by ICP or by Emission Spectrographic Analysis, each
Method, per analyte and up
Millipore Filter Color Rating of Jet Fuel 1 gal
Mineral Oil Separation from Grease and up Mini-Rotary Viscometer, Borderline Pumping Temperature (BPT), ASTM D3829 200 g
Moisture in Gas (Cobalt Bromide Method) 3 cu.ft
Moisture in Gas (Dew Point Method), ASTM D1142 3 cu.ft
Moisture in Gas (KF Method) 3 cu.ft
Moisture in LPG (Valve Freeze Method) 3 gal
Molecular Weight by Boiling
Molecular Weight by Freezing
Molecular Weight of Distillable
Molecular Weight of Lubricating Oils, 50 g
Molybdenum Determination See Metals Determination MTBE by Gas Chromatographic Analysis 10 mL
Naphtha Insolubles 10 mL
Naphthalene Hydrocarbons in Aviation Turbine Fuels by UV Spectrophotometry, ASTM D1840 10 mL
Natural Gases, Flue Gas and Similar Mixtures, Analysis by Gas hromatography 50 mL
Navy Gear Test, per load + parts FTM 791c, 335.3 10 g
Needle Penetration of Bituminous Materials, ASTM D5 100 g
Needle Penetration of Petroleum Waxes, ASTM D1321 100 g
Neutralization Number, Colorimetric,ASTM D974 50 mL
Neutralization Number, Potentiometric, ASTM D664 50 mL
Neutralization Number, Potentiometric,ASTM D664 50 mL
Nickel Determination See Metals Determination Nitrate Nitrate Esters in Diesel Fuel, VV-F-800C 25 mL
Nickel Determination See Metals Determination Nitrate Nitrate Esters in Diesel Fuel,VV-F-800C 25 mL
Nitrite Nitrocellulose Dilution Ratio,ASTM D1720 100 mL
Nitrite Nitrocellulose Dilution Ratio, Nitrogen Oxides in Air and Combustion Gases ASTM D1720 100 mL
Nitrogen Oxides in Air and Combustion Gases 1 g
Nitrogen, ASTM D4629 1 g
Nitrogen, ASTM D4629 1 g
Nitrogen, Kjeldahl, ASTM D3228 20 g
Nitrogen, Kjeldahl, ASTM D3228 20 g
Non-Combustible, ASTM D2276 or D5452 Including Filtration of More Than 100 mL
Non-volatile 10 g
Non-volatile 10 g
Non-volatiles in LPG (O No. or R No.) each 500 mL
Non-volatiles in LPG 500 mL
Norma-Hoffman Oxidation, ASTM D942 50 g
Normal Pentane and Toluene Insolubles in Used Lubricating Oils, ASTM D893 20 mL
Normal Pentane and Toluene Insolubles in Used Lubricating Oils, ASTM D893 20 mL
Octane Rating
Octane Rating
Odorant in LPG, Amperometric method
Odorant in LPG, Amperometric method
Odorant in LPG, Gas Chromatographic 25 g
Odorant in LPG, Gas Chromatographic Method, per analyte and up 25 g
Oil and Grease in Water (Hexane Soluble) 1 gal
Oil Content, Grease, ASTM D128 per run 100 g
Oil Content, Grease, ASTM D128 per run 100 g
Oil Content, Paraffin Wax,ASTM D721 50 g
Oil Content, Paraffin Wax,ASTM D721 50 g
Oils (UOP Method) 300 mL
Panel Coking, FTMS 791b, 3462 600 mL
Panel Coking, RTD Modification, 600 mL or FTMS 791b, 3462
Panel Preparation for Humidity or Salt Spray Tests, Sandblasted or Polished, per panel Paraffin Wax Content of Petroleum Oil or Asphalt (UOP 46-64) 10 g
Particle Contamination, Total and 100 mL
Particle Count, ARP 598A or 100 mL ASTM F312 If 1-5 micron range is included Particle Weight, ASTM F313 100 mL
Particulate Matter in Jet Turbine Fuel, Millipore Filter Color Rating, ASTM D2276 or D5452 1 gal
Penetration of Bituminous Materials, ASTM D5 100 g
Penetration of Grease @ 77 F. 450 g
Penetration of Wax, ASTM D1321 100 g
Peroxide No., ASTM D1832 or D3703 100 mL
pH Value 100 mL
Phase Separation, ASTM D4814 50 mL
Phenol 100 mL
Phosphate in De-icer Fluid 1000 mL
Phosphorus in Gasoline or Fuel,ASTM D3231 100 mL
Phosphorus in Lubricating Oil,ASTM D4047 or D4951 100 mL
Point Change 100 mL
Point Change 200 mL
Pollution Analysis, Air or Water PONA “See Hydrocarbon Types” Potassium Determination See Metals Determination
Pour Point, ASTM D97
Pour Point, Stable 500 mL
Pour Stability Characteristics of 250 mL
Precipitation Number of Lubricating Oils, ASTM D91 100 mL
Preheating Temperature at which (Temperature n/c with
Pressure Viscosity, Isothermal,Ambient to 10,000 psi
Products, FIA, ASTM D1319 including depentanization (required for gasoline
Protection Test, Galvanic Corrosion 50 mL
Protection Test, Salt Water Spray,ASTM B117
Quenchometer, GM, ASTM D3520 500 mL
Quinoline Insoluble, ASTM D893,mod. 200 mL
Ramsbottom Carbon Residue on 10% Residuum 200 mL
Ramsbottom Carbon Residue, ASTM D524 25 mL
Reaction Threshold Temperature at Reduced or Elevated Pressure, ASTM D2883 100 mL
Reaction Threshold Temperature, FTMS 791b, 5050 100 mL
Reactive Liquids (Vulnerable Fluids), ASTM D4486 and up Viscosity Stability @ -40 F. or -65 F., FTMS 791b, 307.1 or ASTM D2532 50 mL
Reduced Pressure Distillation of Petroleum Products, ASTM D1160 500 mL
Refractive Index at 20 C. 10 mL
Reid Vapor Pressure, ASTM D323 1000mL
Request
Reserve Alkalinity of Anti- Freeze, ASTM D1121 100 mL
Residue of Specified Penetration,ASTM D243, per Distillation + Pen. 300 g on
Residue, LPG, R. Number 100 mL
Residue, Mercury Freeze Test 500 mL
Resistance of Grease to Aqueous Solutions, FTMS 791b, 5415 100 g
Resistance of Grease to Fuel,FTMS 791c, 5414.4,par.6.1 or par.6.2 100 g
Roll Stability of Grease (6 hrs. or less) “See Consistency” Rotating Bomb, Oxidation Stability 250 mL
Rubber Swelling 400 mL
Rubber Swelling Index 100 mL
Rubber Swelling, 158 F. to 400 F., 400 mL
Rubber Swelling, o-rings in liquid and vapor (Allison Method) + parts 400 mL
Rust Preventive Characteristics of Steam Turbine Oil, ASTM D665,per run 600 mL
Rust Preventive Characteristics,
Rust Preventive Properties of Lubricating Grease, Alternate Method (Appendix X.2) 2 + parts ASTM D1743 + parts 1/4 lb
Rust Protection FTM 791c, 5329.2 500 mL
Rust Protection, Static Water Drop,FTMS 791b, 5311 50 mL
SAE Load Carrying Capacity, 500 RPM or 1000 RPM + parts (per RPM) 1000 mL Salt Determination, Fuel Oil or Crude Oil 500 mL
Salt Spray Test, ASTM B117 250 mL
Salt Water Immersion 500 mL + parts
Salt Water Immersion, MIL-L-21260C 500 mL
Saponification Number, Colorimetric, ASTM D94 25 g
Saybolt Color, ASTM D156 250 mL
Saybolt Universal Viscosity two viscosity is 150 SUS, Deg. F.)
Sediment and Soluble Sludge, ASTM D1698 Separation Characteristics of
Sediment by Extraction, ASTM D473 50 g
Sediment in Jet Fuel (Filter 1 gallon or 1 litre) 1 gal
Sediment, Millipore Filtration 100 mL
Sediment, Trace (by centrifuge),ASTM D2709 or D2273 250 mL
Separation of Oil from Grease,FTMS 791b, 321.2 50 g
Separation of Oil from Lubricating 1 lb
Silica and Complex Silicates 20 g
Silicon Determination See Metals Determination Silicone Antifoam Agent 10 mL
Silver Corrosion, IP 227 500 mL
Silver Determination Sludge and up Sludge Determination in Mineral 150 mL
Smoke Volatility Index,ASTM D1322 and D86 500 mL
Soap Content of Grease, ASTM D128 200 g
SOD Lead Corrosion,FTMS 791b, 5321.1
Sodium Determination See Metals Determination
Softening Point of Bituminous Materials, Ring and Ball Method, ASTM D36 50 g
Softening Point of Tar Products, Cube-in Water Method, ASTM D61 50 g
Solids, Millipore Filtration, Filter 100 mL
Solubility of Grease in Fuel,FTMS 791b, 5415 100 g
Solvent Extractables in wax, ASTM D3235 50 g
Specific Gravity 60/60 F.
Spectrographic Analysis to Determine Metal Constituents 10 g
Sulfur, Active, ASTM D1662 (including total sulfur) 100 g
Sulfur, Corrosive, Copper Strip, ASTM D130 50 mL and up Sulfur, UV Fluorescence, ASTM D5453 5 g
Sulfur, Total, ASTM D1266 30 g
Sulfur, Total, ASTM D129 (Volatile liquid) 10 g
Sulfur, Total, ASTM D129 10 g
Sulfur, Trace, Lamp or Bomb Method, ASTM D129 or ASTM D1266, Appendix I, modified 25 g
Sulfur, Trace, UV Fluorescence,
Sulfur, X-Ray Method, ASTM D4294 30 mL
Surface Tension @ 77 F, (Plus required density determination) ASTM D1331 100 g
Swelling of Synthetic Rubbers,FTMS 791c, 3603.5 or 3604.2 “See Rubber Swelling” Tetraethyllead, ASTM D3237 Tetraethyllead-Tetramethyllead,
Thermal Conductivity of Liquids, ASTM D2717 100 mL
Thermal Stability of Aviation Turbine Fuels, ASTM D3241 1 L
Thermal Stability of Grease,FTMS 791b, 2503.2 25 g
Thermal Stability of Hydraulic Fluid, ASTM D2160, per run 50 mL
Thermal Stability of Hydraulic Fluid, MIL-H-27601, per run 50 mL
Thermal Stability of Hydraulic Fluid, MIL-L-23699, per run 50 mL
Thermal Stability of U.S. Navy Special Fuel, ASTM D1661 500 mL
Thermal Stability, Cincinnati Milacron Method, Procedure A 1 L 2 Procedure B 1 L
Thermal Stability, FTM 791c 3411.1 50 mL
Thermal Stability, FTM 791c, 2508.1 50 mL
Thermal Value of Fuel Oil, ASTM D240 (Sulfur required) 25 mL
Thermal Value of Gasoline and Jet Fuel, ASTM D240 + sulfur Timken Abrasion, 6 hrs., ASTM D2782, 25 mL Modified 1 gal
Timken Load-Carrying Capacity, ASTM D2782 1 gal
Timken Retention Test (U. S. Steel Method) and up + parts 50 g
Tin Determination See Metals Determination
Titer Test on Fatty Acids + separation of fatty acids 50 g
Torque, Low Temperature (Grease),ASTM D1478 100 g
Total Acid Number, ASTM D664 50 g
Total and Non-combustible Particulate
Total Base Number, ASTM D2896 50 g
Total Base Number, ASTM D664 50 g
Total in Gasoline 10 mL
Total Weight of Particles,Including Non-Combustible Particles 100 mL
Trace Sediment (by Centrifuge),ASTM D2709 or D2273 100 mL
Transformer Oil + Iodine No.Smoke Point, ASTM D1322 250 mL
Ultraviolet Spectrophotometry
Universal Gear Lubricants, ASTM D130 50 mL
Universal Gear Lubricants,FTMS 791b, 3455.1 500 mL
Unsaponifiable Matter, Separation of insoluble fraction 50 g
Unsaponifiable Matter, Separation of soluble fraction 50 g
Unsulfonated Residue of Plant Spray Oil, ASTM D483 100 mL
Vapor Pressure, Isoteniscope, ASTM D2879 Light Oils, Heavy Oils Toxic Substances 50 mL
Vapor Pressure, LPG, ASTM D1267 3000 mL
Vapor Pressure, Reid, ASTM D323 1000 mL
Viscosity by Cold Cranking Simulator,ASTM D5293
Viscosity Index (includes viscosity determinations at 40 C. and 100 C) 100 mL
Viscosity of Volatile and 20 mL
Viscosity of wax, ASTM D3236 500 g
Viscosity, Absolute, ASTM D445 100 mL
Viscosity, Apparent, ASTM D1092 2 lbs
Viscosity, Apparent, Brookfield 500 mL
Viscosity, Apparent, Brookfield,ASTM D2983 50 mL
Viscosity, ASTM D88 or D445
Viscosity, Stormer, ASTM D562 1 L 1
Viscosity,Inherent (Intrinsic) of Polymers, ASTM D2857 10 g
Visual Water
VOC, EPA24 or EPA24A
Volatile Matter in Coal or Coke 200 mL
Volatility, FTMS 791b, 3480 50 mL
Water and Particulate, Haze, ASTM D4176 1 L
Water and Sediment, ASTM D1796 200 mL
Water and Sediment, ASTM D4007 200 mL
Water by Distillation, ASTM D95 100 mL
Water Content of Grease, ASTM D128 100 g
Water Content of Oil and Grease Karl Fischer, ASTM D1533,E203,D4377 100 mL
Water Displacement and Water Stability, FTMS 791c, 3007.2 500 mL
Water Immersion, FTMS 791c, 3463.2 35 g
Water in Insulating Oils by Extraction, ASTM D1315 200 g
Water in Natural Gas and LPG 3 gal or by the Cobalt Bromide Method 3 cu.ft
Water Leachable Sodium Chloride or Fluoride, Each Water Soluble Anions, Viscosity Oil Co. Method
Water Resistance of Grease, ASTM D1264 200 g
Water Sensitivity
Water Separation, MSEP-A or MSEP-B, ASTM D3948 100 mL 1
Water Soluble Chloride – Trace
Water Spray Resistance of Grease, ASTM D4049 200 g
Water Tolerance of Aviation Fuels, Water Reaction Test, ASTM D1094 50 mL
Water Tolerance, Ford BJ-10-3 500 mL
Water Vapor Content of Gaseous Fuels (Cobalt bromide method) 3 gal
Water Washout Characteristics of Greases, ASTM D1264, per run 200 g
Water-Vapor Content of Gaseous Fuels by Measurement of Dew Point Temperature, ASTM D1142 3 cu.ft
Wax Appearance Point of Distillate Fuel, ASTM D3117 200 mL
Wax Content of Petroleum Oil and Asphalt (UOP 46-64) 10 g
Wear Test (Falex) + parts 100 ml.
Wear Test, Distillate Fuels, BOTS + Parts 50 mL
Wear Test, Shell 4-Ball,
Weathering of LPG(R No. or O No.) each 200 ml.
Weatherometer Exposure
Wheel Bearing Grease, Performance
Winter Grade Motor Oils, FTMS 791b, 203, 1959 ASTM App.V
Withdrawn Distillation Range of Lacquer Solvents and Diluents, ASTM D1078 150 mL
Worked Stability of Grease, Shell Roll 200 g.
Workmanship 200 ml.
Zinc Determination See “Metals Determination “