97/23/EC Pressure equipment (PED)
1) 압력용기 지침 PED ( 97/23/EC) 적합성 절차
(1) 압력용기 지침( 97/23/EC)의 구성
서 론 : 해당되는 지침, 전반적인 해설 및 유의사항
본 문 : 적용하기 위한 조문, 가맹국의 법적의무 및 권한
Annex I : 필수 안전 요구사항
Annex II : 적합성 평가 테이블
Annex III : 적합성 평가 절차
Annex IV : 승인기관의 요구조건
Annex V : 사용자 검사관의 요구조건
European Commission에서 제공하는 CE Marking 인증관련 모든 자료가 안내되어있습니다.
(2) 대상기기
대상기기는 최대 허용 압력 0.5 bar 이상을 사용하는 Shell and Water Tube boiler, Heat Exchangers, Plant Vessels, Pressured Storage Containers, Industrial Pipework로써 화학, 정유, 생화학, 식음공정과 에너지 산업 기기류 뿐만 아니라 General Engineering Process에 사용되는 공기가압장비와 가스실린더(Cylinder for breathing air 포함)류 입니다.
다만, 이동용 압력용기 지침 (Transportable Pressure Equipment Directive)과 단순압력용기 지침( Simple Pressure Vessels Directive)에 적용되는 품목은 제외되며 또한 상대적으로 가압이 낮은 제품은 기계지침(Machinery Directive)에 따릅니다.
일반적 의미의 ‘압력 기기’에는 압력 용기, 증기 보일러, 열 교환기, 파이프, 압력 부품, 압력 장치가 포함됩니다. 또한 압력과 관련된 부분에 사용되는 모든 부품과 제품 (플랜지, 노즐, 리프팅, 고속 컨넥터 등) 이 압력기기에 포함됩니다.
일반적으로 아래 안전부품을 포함합니다.
• safety valves,
• bursting disc safety devices,
• buckling rods,
• controlled safety pressure relief systems
• pressure switches
• temperature switches
• fluid level switches
PED에 대한 적합성이 확인된 압력기기는 유럽권역에서 유통 판매를 보장받고 나아가 러시아 등 기타의 국가에서도 적합성을 인정합니다.
저장 된 에너지 (압력 볼륨 제품) 및 사용된 유체의 특성에 따라 결정 되는 위험 수준에 따라 제조자 자체 선언을 하는 가장 낮은 수준인 Category I부터 ISO 9001 품질경영 시스템 및/또는 승인기관 (Notified Body : NB)의 형식시험 (Type Examination)이 요구되는 Category IV까지 분류됩니다.
(3) 대상 제외 기기 Exclusions
이 지침은 부품(components)과 하부 조립품(Sub assemblies)에만 적용 될 뿐이며 산업현장에 설치된 경우 처럼 site에 설치되어 사용자의 책임하에 있는 압력기기에는 적용하지 않습니다. (“assembly of pressure equipment on site and under the responsibility of the user, as in the case of industrial installations”.)
특히 군사용, 운송용 기기 (항공, 해운, 철도, 육상운송 수단에 의해 유체의 운송을 위한 용기: PI Marking 대상)와 기계지침 등 다른 지침에 포함되는 장비는 적용 대상에서 제외합니다.
참조 : 특수한 경우로써 PI Marking과 CE Marking 등 두 가지를 동시에 인증 취득하여야 하는 경우도 있으니 승인기관 (Notified Body : NB)과 상의 할 것을 권장합니다.
설계, 생산 및 테스트에 관하여 해당되는 많은 표준과 규격이 있으며 이들 규격과 표준 등에는 압력기기의 설계 단계부터 생산 및 시험의 각 단계까지를 포함하여 사용되는 자재 및 재료, 용접 및 테스트 방법과 기준이 제시되어 있습니다.
(4) 압력용기 보호규정 Protection requirements.
압력장비는 내부/외부 압력, 주변 및 운전 온도, 정적 압력과 운전과 시험시의 내용물의 량, 교통, 바람, 지진, 부식 및 침식, 피로에 적절한 강도로 설계 되어야 합니다.
안전한 취급과 운전 그리고 시험, 배출과 배기를 보장하는 수단을 제공하여야 합니다.
허용할 수 있는 압력한계의 초과에 대한 보호조치를 제공해야 합니다.
필요한 경우, 외부화제로 손상한계 요건을 충족시키기 위해 적절한 부품을 설계 및 장착하여야 합니다.
영구 접합의 비파괴 시험은 자격을 갖춘 인원에 의해 수행되어야 합니다. 특히 Category III과 IV의 경우, 인원의 자격에 대해 승인되어야 하며 사용되는 자재와 부품의 추적성을 위한 절차가 수립되어야 합니다.
제조업체는 이 지침의 필수적인 성능 요구 사항을 충족하는 능력을 입증하여야 하고 장비의 취급과 사용에 관한 기술적 설명서를 포함하는 기술문서 (Technical Construction File : TCF)를 작성 보관하여야 합니다.
(5) Type of Inspection Documents (EN 10204)
Declaration of compliance with the order “type 2.1″
Document in which the manufacturer declares that the products supplied are in compliance with the requirements of the order, without inclusion of test results.
Test report “type 2.2″
Document in which the manufacturer declares that the products supplied are in compliance with the requirements of the order and in which he supplies test results based on non-specific inspection.
Inspection certificate 3.1 “type 3.1″
Document issued by the manufacturer in which he declares that the products supplied are in compliance with the requirements of the order and in which he supplies test results.
The test unit and the tests to be carried out are defined by the product specification, the official regulation and corresponding rules and/or the order.
The document is validated by the manufacturer’s authorized inspection representative, independent of the manufacturing department.
It shall be permissible for the manufacturer to transfer on to the inspection certificate 3.1 relevant test results obtained by specific inspection on primary or incoming products he uses, provided that the manufacturer operates traceability procedures and can provide the corresponding inspection documents required
Inspection certificate 3.2 “type 3.2″
Document prepared by both the manufacturer’s authorized inspection representative, independent of the manufacturing department and either the purchaser’s authorized inspection representative or the inspector designated by the official regulations and in which they declare that the products supplied are in compliance with
the requirements of the order and in which test results are supplied.
It shall be permissible for the manufacturer to transfer on to the inspection certificate 3.2 relevant test results obtained by specific inspection on primary or incoming products he uses, provided that the manufacturer operates traceability procedures and can provide the corresponding inspection documents required.
Conformity with Annex I section 4.3 of PED 97/23/EC
(6) CE Mark표식
압력 장비는 최소한 다음사항을 표시하여야 합니다.
제조업체명
고유 식별 모델 및 일련 번호
제조년도
최대/최소 허용 압력
CE 로고
(7) 압력용기 지침(PED) 관련 EN규격목록
EN 3-8:2006
Portable fire extinguishers – Part 8: Additional requirements to EN 3-7 for the construction, resistance to pressure and mechanical tests for extinguishers with a maximum allowable pressure equal to or lower than 30 bar
EN 3-8:2006/AC:2007
EN 19:2002
Industrial valves – Marking of metallic valves
EN 267:2009+A1:2011
Automatic forced draught burners for liquid fuels
EN 287-1:2011
Qualification test of welders – Fusion welding – Part 1: Steels
EN 334:2005+A1:2009
Gas pressure regulators for inlet pressures up to 100 bar
EN 378-2:2008+A2:2012 (new)
Refrigerating systems and heat pumps – Safety and environmental requirements – Part 2: Design, construction, testing, marking and documentation
EN 593:2009+A1:2011
Industrial valves – Metallic butterfly valves
EN 676:2003+A2:2008
Automatic forced draught burners for gaseous fuels
EN 676:2003+A2:2008/AC:2008
EN 764-5:2002
Pressure Equipment – Part 5: Compliance and Inspection Documentation of Materials
EN 764-7:2002
Pressure equipment – Part 7: Safety systems for unfired pressure equipment
EN 764-7:2002/AC:2006
EN 1057:2006+A1:2010
Copper and copper alloys – Seamless, round copper tubes for water and gas in sanitary and heating applications
EN 1092-1:2007
Flanges and their joints – Circular flanges for pipes, valves, fittings and accessories, PN designated – Part 1: Steel flanges
EN 1092-3:2003
Flanges and their joints – Circular flanges for pipes, valves, fittings and accessories, PN designated – Part 3: Copper alloy flanges
EN 1092-3:2003/AC:2007
EN 1092-4:2002
Flanges and their joints – Circular flanges for pipes, valves, fittings and accessories, PN designated – Part 4: Aluminium alloy flanges
EN 1171:2002
Industrial valves – Cast iron gate valves
EN 1252-1:1998
Cryogenic vessels – Materials – Part 1: Toughness requirements for temperatures below -80°C
EN 1252-1:1998/AC:1998
EN 1252-2:2001
Cryogenic vessels – Materials – Part 2: Toughness requirements for temperatures between -80°C and -20°C
EN 1349:2009
Industrial process control valves
EN 1515-4:2009
Flanges and their joints – Bolting – Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC
EN 1562:2012 (new)
Founding – Malleable cast irons
EN 1563:2011
Founding – Spheroidal graphite cast irons
EN 1564:2011
Founding – Ausferritic spheroidal graphite cast irons
EN 1591-1:2001+A1:2009
Flanges and their joints – Design rules for gasketed circular flange connections – Part 1: Calculation method
EN 1591-1:2001+A1:2009/AC:2011
EN 1626:2008
Cryogenic vessels – Valves for cryogenic service
EN 1653:1997
Copper and copper alloys – Plate, sheet and circles for boilers, pressure vessels and hot water storage units
EN 1653:1997/A1:2000
EN 1759-3:2003
Flanges and their joints – Circular flanges for pipes, valves, fittings and accessories, Class designated – Part 3: Copper alloy flanges
EN 1759-3:2003/AC:2004
EN 1759-4:2003
Flanges and their joint – Circular flanges for pipes, valves, fittings and accessories, class designated – Part 4: Aluminium alloy flanges
EN 1797:2001
Cryogenic vessels – Gas/material compatibility
EN 1866:2005
Mobile fire extinguishers
EN 1983:2006
Industrial valves – Steel ball valves
EN 1984:2010
Industrial valves – Steel gate valves
EN ISO 4126-1:2004
Safety devices for protection against excessive pressure – Part 1: Safety valves (ISO 4126-1:2004)
EN ISO 4126-1:2004/AC:2006
EN ISO 4126-3:2006
Safety devices for protection against excessive pressure – Part 3: Safety valves and bursting disc safety devices in combination (ISO 4126-3:2006)
EN ISO 4126-4:2004
Safety devices for protection against excessive pressure – Part 4: Pilot operated safety valves (ISO 4126-4:2004)
EN ISO 4126-5:2004
Safety devices for protection against excessive pressure – Part 5: Controlled safety pressure relief systems (CSPRS) (ISO 4126-5:2004)
EN ISO 4126-5:2004/AC:2008
EN ISO 9606-2:2004
Qualification test of welders – Fusion welding – Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
EN ISO 9606-3:1999
Approval testing of welders – Fusion welding – Part 3: Copper and copper alloys (ISO 9606-3:1999)
EN ISO 9606-4:1999
Approval testing of welders – Fusion welding – Part 4: Nickel and nickel alloys (ISO 9606-4:1999)
EN ISO 9606-5:2000
Approval testing of welders – Fusion welding – Part 5: Titanium and titanium alloys, zirconium and zirconium alloys (ISO 9606-5:2000)
EN ISO 9712:2012 (new)
Non-destructive testing – Qualification and certification of NDT personnel (ISO 9712:2012)
EN 10028-1:2007+A1:2009
Flat products made of steels for pressure purposes – Part 1: General requirements
EN 10028-1:2007+A1:2009/AC:2009
EN 10028-2:2009
Flat products made of steels for pressure purposes – Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10028-3:2009
Flat products made of steels for pressure purposes – Part 3: Weldable fine grain steels, normalized
EN 10028-4:2009
Flat products made of steels for pressure purposes – Part 4: Nickel alloy steels with specified low temperature properties
EN 10028-5:2009
Flat products made of steels for pressure purposes – Part 5: Weldable fine grain steels, thermomechanically rolled
EN 10028-6:2009
Flat products made of steels for pressure purposes – Part 6: Weldable fine grain steels, quenched and tempered
EN 10028-7:2007
Flat products made of steels for pressure purposes – Part 7: Stainless steels
EN 10204:2004
Metallic products – Types of inspection documents
EN 10213:2007
Steel castings for pressure purposes
EN 10213:2007/AC:2008
EN 10216-1:2002
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 1: Non-alloy steel tubes with specified room temperature properties
EN 10216-1:2002/A1:2004
EN 10216-2:2002+A2:2007
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties
EN 10216-3:2002
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 3: Alloy fine grain steel tubes
EN 10216-3:2002/A1:2004
EN 10216-4:2002
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 4: Non-alloy and alloy steel tubes with specified low temperature properties
EN 10216-4:2002/A1:2004
EN 10216-5:2004
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 5: Stainless steel tubes
EN 10216-5:2004/AC:2008
EN 10217-1:2002
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 1: Non-alloy steel tubes with specified room temperature properties
EN 10217-1:2002/A1:2005
EN 10217-2:2002
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties
EN 10217-2:2002/A1:2005
EN 10217-3:2002
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 3: Alloy fine grain steel tubes
EN 10217-3:2002/A1:2005
EN 10217-4:2002
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 4: Electric welded non-alloy steel tubes with specified low temperature properties
EN 10217-4:2002/A1:2005
EN 10217-5:2002
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties
EN 10217-5:2002/A1:2005
EN 10217-6:2002
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties
EN 10217-6:2002/A1:2005
EN 10217-7:2005
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 7: Stainless steel tubes
EN 10222-1:1998
Steel forgings for pressure purposes – Part 1: General requirements for open die forgings
EN 10222-1:1998/A1:2002
EN 10222-2:1999
Steel forgings for pressure purposes – Part 2: Ferritic and martensitic steels with specified elevated temperature properties
EN 10222-2:1999/AC:2000
EN 10222-3:1998
Steel forgings for pressure purposes – Part 3: Nickel steels with specified low temperature properties
EN 10222-4:1998
Steel forgings for pressure purposes – Part 4: Weldable fine grain steels with high proof strength
EN 10222-4:1998/A1:2001
EN 10222-5:1999
Steel forgings for pressure purposes – Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels
EN 10222-5:1999/AC:2000
EN 10253-2:2007
Butt-welding pipe fittings – Part 2: Non alloy and ferritic alloy steels with specific inspection requirements
EN 10253-4:2008
Butt-welding pipe fittings – Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
EN 10253-4:2008/AC:2009
EN 10269:1999
Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
EN 10269:1999/A1:2006
EN 10269:1999/A1:2006/AC:2008
EN 10272:2007
Stainless steel bars for pressure purposes
EN 10273:2007
Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties
EN 10305-4:2011
Steel tubes for precision applications – Technical delivery conditions – Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems
EN 10305-6:2005
Steel tubes for precision applications – Technical delivery conditions – Part 6: Welded cold drawn tubes for hydraulic and pneumatic power systems
EN ISO 10931:2005
Plastics piping systems for industrial applications – Poly(vinylidene fluoride) (PVDF) – Specifications for components and the system (ISO 10931:2005)
EN 12178:2003
Refrigerating systems and heat pumps – Liquid level indicating devices – Requirements, testing and marking
EN 12263:1998
Refrigerating systems and heat pumps – Safety switching devices for limiting the pressure – Requirements and tests
EN 12266-1:2012 (new)
Industrial valves – Testing of metallic valves – Part 1: Pressure tests, test procedures and acceptance criteria – Mandatory requirements
EN 12284:2003
Refrigerating systems and heat pumps – Valves – Requirements, testing and marking
EN 12288:2010
Industrial valves – Copper alloy gate valves
EN 12334:2001
Industrial valves – Cast iron check valves
EN 12334:2001/A1:2004
EN 12334:2001/AC:2002
EN 12392:2000
Aluminium and aluminium alloys – Wrought products – Special requirements for products intended for the production of pressure equipment
EN 12420:1999
Copper and copper alloys – Forgings
EN 12434:2000
Cryogenic vessels – Cryogenic flexible hoses
EN 12434:2000/AC:2001
EN 12451:2012 (new)
Copper and copper alloys – Seamless, round tubes for heat exchangers
EN 12452:2012 (new)
Copper and copper alloys – Rolled, finned, seamless tubes for heat exchangers
EN 12516-1:2005
Industrial valves – Shell design strength – Part 1: Tabulation method for steel valve shells
EN 12516-1:2005/AC:2007
EN 12516-2:2004
Industrial valves – Shell design strength – Part 2: Calculation method for steel valve shells
EN 12516-3:2002
Valves – Shell design strength – Part 3: Experimental method
EN 12516-3:2002/AC:2003
EN 12516-4:2008
Industrial valves – Shell design strength – Part 4: Calculation method for valve shells manufactured in metallic materials other than steel
EN 12542:2010
LPG equipment and accessories – Static welded steel cylindrical tanks, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m³ – Design and manufacture
EN 12735-1:2010
Copper and copper alloys – Seamless, round copper tubes for air conditioning and refrigeration – Part 1: Tubes for piping systems
EN 12735-2:2010
Copper and copper alloys – Seamless, round copper tubes for air conditioning and refrigeration – Part 2: Tubes for equipment
EN 12778:2002
Cookware – Pressure cookers for domestic use
EN 12778:2002/A1:2005
EN 12778:2002/AC:2003
EN 12952-1:2001
Water-tube boilers and auxiliary installations – Part 1: General
EN 12952-2:2011
Water-tube boilers and auxiliary installations – Part 2: Materials for pressure parts of boilers and accessories
EN 12952-3:2011
Water-tube boilers and auxiliary installations – Part 3: Design and calculation for pressure parts of the boiler
EN 12952-5:2011
Water-tube boilers and auxiliary installations – Part 5: Workmanship and construction of pressure parts of the boiler
EN 12952-6:2011
Water-tube boilers and auxiliary installations – Part 6: Inspection during construction; documentation and marking of pressure parts of the boiler
EN 12952-7:2002
Water-tube boilers and auxiliary installations – Part 7: Requirements for equipment for the boiler
EN 12952-8:2002
Water-tube boilers and auxiliary installations – Part 8: Requirements for firing systems for liquid and gaseous fuels for the boiler
EN 12952-9:2002
Water-tube boilers and auxiliary installations – Part 9: Requirements for firing systems for pulverized solid fuels for the boiler
EN 12952-10:2002
Water-tube boilers and auxiliary installations – Part 10: Requirements for safeguards against excessive pressure
EN 12952-11:2007
Water-tube boilers and auxiliary installations – Part 11: Requirements for limiting devices of the boiler and accessories
EN 12952-14:2004
Water-tube boilers and auxiliary installations – Part 14: Requirements for flue gas DENOX-systems using liquefied pressurized ammonia and ammonia water solution
EN 12952-16:2002
Water-tube boilers and auxiliary installations – Part 16: Requirements for grate and fluidized-bed firing systems for solid fuels for the boiler
EN 12953-1:2012 (new)
Shell boilers – Part 1: General
EN 12953-2:2012 (new)
Shell boilers – Part 2: Materials for pressure parts of boilers and accessories
EN 12953-3:2002
Shell boilers – Part 3: Design and calculation for pressure parts
EN 12953-4:2002
Shell boilers – Part 4: Workmanship and construction of pressure parts of the boiler
EN 12953-5:2002
Shell boilers – Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler
EN 12953-6:2011
Shell Boilers – Part 6: Requirements for equipment for the boiler
EN 12953-7:2002
Shell boilers – Part 7 : Requirements for firing systems for liquid and gaseous fuels for the boilers
EN 12953-8:2001
Shell boilers – Part 8: Requirements for safeguards against excessive pressure
EN 12953-8:2001/AC:2002
EN 12953-9:2007
Shell boilers – Part 9: Requirements for limiting devices of the boiler and accessories
EN 12953-12:2003
Shell boilers – Part 12: Requirements for grate firing systems for solid fuels for the boiler
EN 12953-13:2012 (new)
Shell boilers – Part 13: Operating instructions
EN 13121-1:2003
GRP tanks and vessels for use above ground – Part 1: Raw materials – Specification conditions and acceptance conditions
EN 13121-2:2003
GRP tanks and vessels for use above ground – Part 2: Composite materials – Chemical resistance
EN 13121-3:2008+A1:2010
GRP tanks and vessels for use above ground – Part 3: Design and workmanship
EN 13121-3:2008+A1:2010/AC:2011
EN 13134:2000
Brazing – Procedure approval
EN 13136:2001
Refrigerating systems and heat pumps – Pressure relief devices and their associated piping – Methods for calculation
EN 13136:2001/A1:2005
EN 13175:2003+A2:2007
LPG equipment and accessories – Specification and testing for Liquefied Petroleum Gas (LPG) tank valves and fittings
EN 13348:2008
Copper and copper alloys – Seamless, round copper tubes for medical gases or vacuum
EN 13371:2001
Cryogenic vessels – Couplings for cryogenic service
EN 13397:2001
Industrial valves – Diaphragm valves made of metallic materials
EN 13445-1:2009
Unfired pressure vessels – Part 1: General
EN 13445-2:2009
Unfired pressure vessels – Part 2: Materials
EN 13445-2:2009/A1:2012 (new)
EN 13445-2:2009/A2:2012 (new)
EN 13445-3:2009
Unfired pressure vessels – Part 3: Design
EN 13445-3:2009/A1:2012 (new)
EN 13445-4:2009
Unfired pressure vessels – Part 4: Fabrication
EN 13445-4:2009/A1:2011
EN 13445-5:2009
Unfired pressure vessels – Part 5: Inspection and testing
EN 13445-5:2009/A2:2011
EN 13445-5:2009/A3:2011
EN 13445-5:2009/A1:2011
EN 13445-6:2009
Unfired pressure vessels – Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron
EN 13445-8:2009
Unfired pressure vessels – Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
EN 13458-1:2002
Cryogenic vessels – Static vacuum insulated vessels – Part 1: Fundamental requirements
EN 13458-2:2002
Cryogenic vessels – Static vacuum insulated vessels – Part 2: Design, fabrication, inspection and testing
EN 13458-2:2002/AC:2006
EN 13458-3:2003
Cryogenic vessels – Static vacuum insulated vessels – Part 3: Operational requirements
EN 13458-3:2003/A1:2005
EN 13480-1:2012 (new)
Metallic industrial piping – Part 1: General
EN 13480-2:2012 (new)
Metallic industrial piping – Part 2: Materials
EN 13480-3:2012 (new)
Metallic industrial piping – Part 3: Design and calculation
EN 13480-4:2012 (new)
Metallic industrial piping – Part 4: Fabrication and installation
EN 13480-5:2012 (new)
Metallic industrial piping – Part 5: Inspection and testing
EN 13480-6:2012 (new)
Metallic industrial piping – Part 6: Additional requirements for buried piping
EN 13480-8:2012 (new)
Metallic industrial piping – Part 8: Additional requirements for aluminium and aluminium alloy piping
EN ISO 13585:2012 (new)
Brazing – Qualification test of brazers and brazing operators (ISO 13585:2012)
EN 13611:2007+A2:2011
Safety and control devices for gas burners and gas burning appliances – General requirements
EN 13648-1:2008
Cryogenic vessels – Safety devices for protection against excessive pressure – Part 1: Safety valves for cryogenic service
EN 13648-2:2002
Cryogenic vessels – Safety devices for protection against excessive pressure – Part 2: Bursting disc safety devices for cryogenic service
EN 13648-3:2002
Cryogenic vessels – Safety devices for protection against excessive pressure – Part 3: Determination of required discharge – Capacity and sizing
EN 13709:2010
Industrial valves – Steel globe and globe stop and check valves
EN 13789:2010
Industrial valves – Cast iron globe valves
EN 13831:2007
Closed expansion vessels with built in diaphragm for installation in water
EN 13835:2012 (new)
Founding – Austenitic cast irons
EN 13923:2005
Filament-wound FRP pressure vessels – Materials, design, manufacturing and testing
EN 14071:2004
Pressure relief valves for LPG tanks – Ancillary equipment
EN 14129:2004
Pressure relief valves for LPG tanks
EN 14197-1:2003
Cryogenic vessels – Static non-vacuum insulated vessels – Part 1: Fundamental requirements
EN 14197-2:2003
Cryogenic vessels – Static non-vacuum insulated vessels – Part 2: Design, fabrication, inspection and testing
EN 14197-2:2003/A1:2006
EN 14197-2:2003/AC:2006
EN 14197-3:2004
Cryogenic vessels – Static non-vacuum insulated vessels – Part 3: Operational requirements
EN 14197-3:2004/A1:2005
EN 14197-3:2004/AC:2004
EN 14222:2003
Stainless steel shell boilers
EN 14276-1:2006+A1:2011
Pressure equipment for refrigerating systems and heat pumps – Part 1: Vessels – General requirements
EN 14276-2:2007+A1:2011
Pressure equipment for refrigerating systems and heat pumps – Part 2: Piping – General requirements
EN 14341:2006
Industrial valves – Steel check valves
EN 14359:2006+A1:2010
Gas-loaded accumulators for fluid power applications
EN 14382:2005+A1:2009
Safety devices for gas pressure regulating stations and installations – Gas safety shut-off devices for inlet pressures up to 100 bar
EN 14382:2005+A1:2009/AC:2009
EN 14394:2005+A1:2008
Heating boilers – Heating boilers with forced draught burners – Nominal heat output not exceeding 10 MW and maximum operating temperature of 110 °C
EN 14570:2005
Equipping of LPG tanks, overground and underground
EN 14570:2005/A1:2006
EN 14585-1:2006
Corrugated metal hose assemblies for pressure applications – Part 1: Requirements
EN 14917:2009+A1:2012 (new)
Metal bellows expansion joints for pressure applications
EN 15001-1:2009
Gas Infrastructure – Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations – Part 1: Detailed functional requirements for design, materials, construction, inspection and testing
EN ISO 15493:2003
Plastics piping systems for industrial applications – Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) – Specifications for components and the system – Metric series (ISO 15493:2003)
EN ISO 15494:2003
Plastics piping systems for industrial applications – Polybutene (PB), polyethylene (PE) and polypropylene (PP) – Specifications for components and the system – Metric series (ISO 15494:2003)
EN ISO 15613:2004
Specification and qualification of welding procedures for metallic materials – Qualification based on pre-production welding test (ISO 15613:2004)
EN ISO 15614-1:2004
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys (ISO 15614-1:2004)
EN ISO 15614-1:2004/A1:2008
EN ISO 15614-1:2004/A2:2012 (new)
EN ISO 15614-2:2005
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
EN ISO 15614-2:2005/AC:2009
EN ISO 15614-4:2005
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 4: Finishing welding of aluminium castings (ISO 15614-4:2005)
EN ISO 15614-4:2005/AC:2007
EN ISO 15614-5:2004
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 5: Arc welding of titanium, zirconium and their alloys (ISO 15614-5:2004)
EN ISO 15614-6:2006
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 6: Arc and gas welding of copper and its alloys (ISO 15614-6:2006)
EN ISO 15614-7:2007
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 7: Overlay welding (ISO 15614-7:2007)
EN ISO 15614-8:2002
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 8: Welding of tubes to tube-plate joints (ISO 15614-8:2002)
EN ISO 15614-11:2002
Specification and qualification of welding procedures for metallic materials – Welding procedure test – Part 11: Electron and laser beam welding (ISO 15614-11:2002)
EN ISO 15620:2000
Welding – Friction welding of metallic materials (ISO 15620:2000)
EN 15776:2011
Unfired pressure vessels – Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 %
EN ISO 16135:2006
Industrial valves – Ball valves of thermoplastics materials (ISO 16135:2006)
EN ISO 16136:2006
Industrial valves – Butterfly valves of thermoplastics materials (ISO 16136:2006)
EN ISO 16137:2006
Industrial valves – Check valves of thermoplastics materials (ISO 16137:2006)
EN ISO 16138:2006
Industrial valves – Diaphragm valves of thermoplastics materials (ISO 16138:2006)
EN ISO 16139:2006
Industrial valves – Gate valves of thermoplastics materials (ISO 16139:2006)
EN ISO 21787:2006
Industrial valves – Globe valves of thermoplastics materials (ISO 21787:2006)
