2006/95/EC Low Voltage Directive (LVD)

1. 저전압지침(2006/95/EC)의 구성

서 론 : 해당되는 지침, 전반적인 해설 및 유의사항
지침본문 : 적용하기 위한 조문, 가맹국의 법적 의무나 권한
Annex I : 안전에 관한 설계 일반 지침 및 기본 요구사항
Annex II : 지침대상 외의 기기
Annex III : A. CE-Marking 표시. B. 적합성 선언서
Annex IV : 내부 제조관리. 기술문서 및 선언서 보관, 제조공정의 관리

Eurasian Commission 제공 – 인증지침,인증안내서,승인기관 조회 등

European Commission에서 제공하는 CE Marking 인증관련 모든 자료가 안내되어있습니다.

2. 대상기기

교류 50-1000 V 및 직류 75-1500V의 정격전압으로 사용하도록 설계된 기기를 적용대상으로 합니다. 많은 기기들이 전기를 동력원으로 사용하기에 적용기기 분야가 다양합니다.

top

3. 대상 외의 기기(지침 Annex Ⅱ)

다른 기술 지침에 따라 관리되는 대상의 기기로써 다음과 같습니다.

A) 폭발환경에서 사용되는 전기기기
B) 방사선 및 의료용 전기기기
C) 가정용 플러그 및 소켓
D) 화물 및 승객용 엘리베이터의 전기 부품
E) 전력계(Electricity meters)
F) 전기 펜스의 제어기

선박, 항공기, 철도에서 사용되는 특정한 전기기기로써, 가맹국이 참가하고 있는 국제 기관에 의 해 제정 되어진 안전 규격에 적합한 기기

top

4. 기술문서에 포함사항

A) 자기 적합성 선언서
B) 해당 전기기기의 개요
C) 설계도면
D) 전기회로도면
E) 제품 기술과 사용, 운전 설명서
F) 부품목록 및 부품의 CE인증 취득여부
G) 설계계산
H) 시험성적서

top

5. 인증절차

일반적으로 인증기관에서 발행하는 CoC(Certificate of Conformity)가 아닌 자기 적합성 선언서 인 DoC( Declaration of Conformity)를 취득합니다.

인증취득 기업체는 시험소 또는 자체 시험을 통해서 인증대상제품이 해당규격에 적합함을 입증하는 성적서를 구비하여 관련 문서를 만들고 인증취득 기업체의 대표자가 선언서에 서명하는 것입니다. 특별히 인증취득 기업이 제 3자 인증기관의 인증서 발급을 요구하지 않는한 CoC 인증서를 발급하지 않습니다.

top

6. 저전압 지침 관련 EN 규격 목록

EN 41003 ; Particular safety requirements for equipment to be connected to telecommunication networks and/or a cable distribution system
EN 50065-4-2 ; Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz — Part 4-2: Low voltage decoupling filters – Safety requirements
EN 50065-4-7 ; Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz — Part 4-7: Portable low voltage decoupling filters – Safety requirements
EN 50085-1 ; Cable trunking systems and cable ducting systems for electrical installations — Part 1: General requirements
EN 50085-2-1 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-1: Cable trunking systems and cable ducting systems intended for mounting on walls and ceilings
EN 50085-2-2 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-2: Particular requirements for cable trunking systems and cable ducting systems intended for mounting underfloor, flushfloor, or onfloor
EN 50085-2-3 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets
EN 50085-2-4 ; Cable trunking systems and cable ducting systems for electrical installations — Part 2-4: Particular requirements for service poles and service posts
EN 50086-2-4 ; Conduit systems for cable management — Part 2-4: Particular requirements for conduit systems buried underground
EN 50090-2-2 ; Home and Building Electronic Systems (HBES) — Part 2-2: System overview – General technical requirements
EN 50106 ; Safety of household and similar electrical appliances – Particular rules for routine tests referring to appliances under the scope of EN 60335-1
EN 50117-1 ; Coaxial cables — Part 1: Generic specification
EN 50117-2-1 ; Coaxial cables — Part 2-1: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 1 000 MHz
EN 50117-2-2 ; Coaxial cables — Part 2-2: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 1 000 MHz
EN 50117-2-3 ; Coaxial cables — Part 2-3: Sectional specification for cables used in cabled distribution networks – Distribution and trunk cables for systems operating at 5 MHz – 1 000 MHz
EN 50117-2-4 ; Coaxial cables — Part 2-4: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz
EN 50117-2-5 ; Coaxial cables — Part 2-5: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 3 000 MHz
EN 50117-3-1 ; Coaxial cables — Part 3-1: Sectional specifications for cables used in Telecom applications – Miniaturized cables used in digital communication systems
EN 50117-4-1 ; Coaxial cables — Part 4-1: Sectional specification for cables for BCT cabling in accordance with EN 50173 – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz
EN 50156-1 ; Electrical equipment for furnaces and ancillary equipment — Part 1: Requirements for application design and installation
EN 50178 ; Electronic equipment for use in power installations
EN 50214 ; Flat polyvinyl chloride sheathed flexible cables
EN 50250 ; Conversion adaptors for industrial use
EN 50262 ; Cable glands for electrical installations
EN 50267-1 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 1: Apparatus
EN 50267-2-1 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 2-1: Procedures – Determination of the amount of halogen acid gas
EN 50267-2-2 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 2-2: Procedures – Determination of degree of acidity of gases for materials by measuring pH and conductivity
EN 50267-2-3 ; Common test methods for cables under fire conditions – Tests on gases evolved during combustion of materials from cables — Part 2-3: Procedures – Determination of degree of acidity of gases for cables by determination of the weighted average of pH and conductivity
EN 50274 ; Low-voltage switchgear and controlgear assemblies – Protection against electric shock – Protection against unintentional direct contact with hazardous live parts
EN 50288-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 1: Generic specification
EN 50288-10-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 10-1: Sectional specification for screened cables characterized up to 500 MHz – Horizontal floor and building backbone cables
EN 50288-11-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 11-1: Sectional specification for un-screened cables characterised up to 500 MHz – Horizontal and building backbone cables
EN 50288-2-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 2-1: Sectional specification for screened cables characterised up to 100 MHz – Horizontal and building backbone cables
EN 50288-2-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 2-2: Sectional specification for screened cables characterised up to 100 MHz – Work area and patch cord cables
EN 50288-3-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 3-1: Sectional specification for unscreened cables characterised up to 100 MHz – Horizontal and building backbone cables
EN 50288-3-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz – Work area and patch cord cables
EN 50288-4-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 4-1: Sectional specification for screened cables characterised up to 600 MHz – Horizontal and building backbone cables
EN 50288-4-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 4-2: Sectional specification for screened cables characterised up to 600 MHz – Work area and patch cord cables
EN 50288-5-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 5-1: Sectional specification for screened cables characterized up to 250 MHz – Horizontal and building backbone cables
EN 50288-5-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 5-2: Sectional specification for screened cables characterized up to 250 MHz – Work area and patch cord cables
EN 50288-6-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 6-1: Sectional specification for unscreened cables characterised up to 250 MHz – Horizontal and building backbone cables
EN 50288-6-2 ; Multi-element metallic cables used in analogue and digital communication and control — Part 6-2: Sectional specification for unscreened cables characterised up to 250 MHz – Work area and patch cord cables
EN 50288-7 ; Multi-element metallic cables used in analogue and digital communication and control — Part 7: Sectional specification for instrumentation and control cables
EN 50288-8 ; Multi-element metallic cables used in analogue and digital communication and control — Part 8: Specification for type 1 cables characterised up to 2 MHz
EN 50288-9-1 ; Multi-element metallic cables used in analogue and digital communication and control — Part 9-1: Sectional specification for screened cables characterised up to 1 000 MHz – Horizontal and building backbone cables
EN 50289-1-3 ; Communication cables – Specifications for test methods — Part 1-3: Electrical test methods – Dielectric strength
EN 50289-1-4 ; Communication cables – Specifications for test methods — Part 1-4: Electrical test methods – Insulation resistance
EN 50290-2-1 ; Communication cables — Part 2-1: Common design rules and construction
EN 50290-2-20 ; Communication cables — Part 2-20: Common design rules and construction – General
EN 50290-2-21 ; Communication cables — Part 2-21: Common design rules and construction – PVC insulation compounds
EN 50290-2-22 ; Communication cables — Part 2-22: Common design rules and construction – PVC sheathing compounds
EN 50290-2-23 ; Communication cables — Part 2-23: Common design rules and construction – PE insulation
EN 50290-2-24 ; Communication cables — Part 2-24: Common design rules and construction – PE sheathing
EN 50290-2-25 ; Communication cables — Part 2-25: Common design rules and construction – Polypropylene insulation compounds
EN 50290-2-26 ; Communication cables — Part 2-26: Common design rules and construction – Halogen free flame retardant insulation compounds
EN 50290-2-27 ; Communication cables — Part 2-27: Common design rules and construction – Halogen free flame retardant thermoplastic sheathing compounds
EN 50290-2-28 ; Communication cables — Part 2-28: Common design rules and construction – Filling compounds for filled cables
EN 50290-2-29 ; Communication cables — Part 2-29: Common design rules and construction – Cross-linked PE insulation compounds
EN 50290-2-30 ; Communication cables — Part 2-30: Common design rules and construction – Poly(tetrafluoroethylene-hexafluoropropylene) (FEP) insulation and sheathing
EN 50290-4-1 ; Communication cables — Part 4-1: General considerations for the use of cables – Environmental conditions and safety aspects
EN 50363-0 ; Insulating, sheathing and covering materials for low-voltage energy cables — Part 0: General introduction
EN 50363-0 ; Insulating, sheathing and covering materials for low-voltage energy cables — Part 0: General introduction
EN 50363-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 1: Cross-linked elastomeric insulating compounds
EN 50363-10-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 10-1: Miscellaneous sheathing compounds – Cross-linked polyvinyl chloride (XLPVC)
EN 50363-10-2 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 10-2: Miscellaneous sheathing compounds – Thermoplastic polyurethane
EN 50363-2-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 2-1: Cross-linked elastomeric sheathing compounds
EN 50363-2-2 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 2-2: Cross-linked elastomeric covering compounds
EN 50363-3 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 3: PVC insulating compounds
EN 50363-4-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 4-1: PVC sheathing compounds
EN 50363-4-2 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 4-2: PVC covering compounds
EN 50363-5 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 5: Halogen-free, cross-linked insulating compounds
EN 50363-6 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 6: Halogen-free, cross-linked sheathing compounds
EN 50363-7 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 7: Halogen-free, thermoplastic insulating compounds
EN 50363-8 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 8: Halogen-free, thermoplastic sheathing compounds
EN 50363-9-1 ; Insulating, sheathing and covering materials for low voltage energy cables — Part 9-1: Miscellaneous insulating compounds – Cross-linked polyvinyl chloride (XLPVC)
EN 50364 ; Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications
EN 50369 ; Liquid tight sheathing systems for cable management
EN 50371 ; Generic standard to demonstrate the compliance of low power electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (10 MHz – 300 GHz) – General public
EN 50395 ; Electrical test methods for low voltage energy cables
EN 50396 ; Non electrical test methods for low voltage energy cables
EN 50406-1 ; End user multi-pair cables used in high bit rate telecommunication networks — Part 1: Aerial cables
EN 50406-2 ; End user multi-pair cables used in high bit rate telecommunication networks — Part 2: Duct and buried cables
EN 50407-1 ; Multi-pair cables used in high bit rate digital access telecommunication networks — Part 1: Outdoor cables
EN 50425 ; Switches for household and similar fixed electrical installations – Collateral standard – Fireman’s switches for exterior and interior signs and luminaires
EN 50428 ; Switches for household and similar fixed electrical installations – Collateral standard – Switches and related accessories for use in home and building electronic systems (HBES)
EN 50441-1 ; Cables for indoor residential telecommunication installations — Part 1: Unscreened cables – Grade 1
EN 50441-1 ; Cables for indoor residential telecommunication installations — Part 1: Unscreened cables – Grade 1
EN 50441-2 ; Cables for indoor residential telecommunication installations — Part 2: Screened cables – Grade 1
EN 50441-2 ; Cables for indoor residential telecommunication installations — Part 2: Screened cables – Grade 2
EN 50441-3 ; Cables for indoor residential telecommunication installations — Part 3: Screened cables – Grade 3
EN 50441-4 ; Cables for indoor residential telecommunication installations — Part 4: Cables up to 1 200 MHz – Grade 3
EN 50445 ; Product family standard to demonstrate compliance of equipment for resistance welding, arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic fields (0 Hz – 300 GHz)
EN 50491-3 ; General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) — Part 3: Electrical safety requirements
EN 50491-4-1 ; General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) — Part 4-1: General functional safety requirements for products intended to be integrated in Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS)
EN 50497 ; Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables
EN 50520 ; Cover plates and cover tapes for the protection and location warning of buried cables or buried conduits in underground installations
EN 50525-1 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 1: General requirements
EN 50525-2-11 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) — Part 2-11: Cables for general applications – Flexible cables with thermoplastic PVC insulation
EN 50525-2-12 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) — Part 2-12: Cables for general applications – Cables with thermoplastic PVC insulation for extensible leads
EN 50525-2-21 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) — Part 2-21: Cables for general applications – Flexible cables with crosslinked elastomeric insulation
EN 50525-2-22 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-22: Cables for general applications – High flexibility braided cables with crosslinked elastomeric insulation
EN 50525-2-31 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-31: Cables for general applications – Single core non-sheathed cables with thermoplastic PVC insulation
EN 50525-2-41 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-41: Cables for general applications – Single core cables with crosslinked silicone rubber insulation
EN 50525-2-42 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-42: Cables for general applications – Single core non-sheathed cables with crosslinked EVA insulation
EN 50525-2-51 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-51: Cables for general applications – Oil resistant control cables with thermoplastic PVC insulation
EN 50525-2-71 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-71: Cables for general applications – Flat tinsel cables (cords) with thermoplastic PVC insulation
EN 50525-2-72 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-72: Cables for general applications – Flat divisible cables (cords) with thermoplastic PVC insulation
EN 50525-2-81 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-81: Cables for general applications – Cables with crosslinked elastomeric covering for arc welding
EN 50525-2-82 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-82: Cables for general applications – Cables with crosslinked elastomeric insulation for decorative chains
EN 50525-2-83 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 2-83: Cables for general applications – Multicore cables with crosslinked silicone rubber insulation
EN 50525-3-11 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-11: Cables with special fire performance – Flexible cables with halogen-free thermoplastic insulation, and low emission of smoke
EN 50525-3-21 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-21: Cables with special fire performance – Flexible cables with halogen-free crosslinked insulation, and low emission of smoke
EN 50525-3-31 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-31: Cables with special fire performance – Single core non-sheathed cables with halogen-free thermoplastic insulation, and low emission of smoke
EN 50525-3-41 ; Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) — Part 3-41: Cables with special fire performance – Single core non-sheathed cables with halogen-free crosslinked insulation, and low emission of smoke
EN 50550 ; Power frequency overvoltage protective device for household and similar applications (POP)
EN 50557 ; Requirements for automatic reclosing devices (ARDs) for circuit breakers-RCBOs-RCCBs for household and similar uses
EN 60034-1 ; Rotating electrical machines — Part 1: Rating and performance
EN 60034-1 ; Rotating electrical machines — Part 1: Rating and performance
EN 60034-11 ; Rotating electrical machines — Part 11: Thermal protection
EN 60034-12 ; Rotating electrical machines — Part 12: Starting performance of single-speed three-phase cage induction motors
EN 60034-14 ; Rotating electrical machines — Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher – Measurement, evaluation and limits of vibration severity
EN 60034-5 ; Rotating electrical machines — Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) – Classification
EN 60034-6 ; Rotating electrical machines — Part 6: Methods of cooling (IC Code)
EN 60034-7 ; Rotating electrical machines — Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)
EN 60034-8 ; Rotating electrical machines — Part 8: Terminal markings and direction of rotation
EN 60034-9 ; Rotating electrical machines — Part 9: Noise limits
EN 60051-1 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 1: Definitions and general requirements common to all parts
EN 60051-2 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 2: Special requirements for ammeters and voltmeters
EN 60051-3 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 3: Special requirements for wattmeters and varmeters
EN 60051-4 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 4: Special requirements for frequency meters
EN 60051-5 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 5: Special requirements for phase meters, power factor meters and synchroscopes
EN 60051-6 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
EN 60051-7 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 7: Special requirements for multi-function instruments
EN 60051-8 ; Direct acting indicating analogue electrical measuring instruments and their accessories — Part 8: Special requirements for accessories
EN 60051-9 ; Direct acting indicating analogue electrical-measuring instruments and their accessories — Part 9: Recommended test methods
EN 60061-1 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 1: Lamp caps
EN 60061-2 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 2: Lampholders
EN 60061-3 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 3: Gauges
EN 60061-4 ; Lamp caps and holders together with gauges for the control of interchangeability and safety — Part 4: Guidelines and general information
EN 60065 ; Audio, video and similar electronic apparatus – Safety requirements
EN 60110-1 ; Power capacitors for induction heating installations — Part 1: General
EN 60127-1 ; Miniature fuses — Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links
EN 60127-2 ; Miniature fuses — Part 2: Cartridge fuse-links
EN 60127-3 ; Miniature fuses — Part 3: Sub-miniature fuse-links
EN 60127-4 ; Miniature fuses — Part 4: Universal modular fuse-links (UMF) – Through-hole and surface mount types
EN 60127-6 ; Miniature fuses — Part 6: Fuse-holders for miniature fuse-links
EN 60143-2 ; Series capacitors for power systems — Part 2: Protective equipment for series capacitor banks
EN 60155 ; Glow-starters for fluorescent lamps
EN 60204-1 ; Safety of machinery – Electrical equipment of machines — Part 1: General requirements
EN 60204-32 ; Safety of machinery – Electrical equipment of machines — Part 32: Requirements for hoisting machines
EN 60215 ; Safety requirements for radio transmitting equipment
EN 60228 ; Conductors of insulated cables
EN 60238 ; Edison screw lampholders
EN 60252-1 ; AC motor capacitors — Part 1: General – Performance, testing and rating – Safety requirements – Guidance for installation and operation
EN 60252-1 ; AC motor capacitors — Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
EN 60252-2 ; AC motor capacitors — Part 2: Motor start capacitors
EN 60252-2 ; AC motor capacitors — Part 2: Motor start capacitors
EN 60255-27 ; Measuring relays and protection equipment — Part 27: Product safety requirements
EN 60255-5 ; Electrical relays — Part 5: Insulation coordination for measuring relays and protection equipment – Requirements and tests
EN 60269-1 ; Low-voltage fuses — Part 1: General requirements
EN 60269-4 ; Low-voltage fuses — Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices
EN 60269-6 ; Low-voltage fuses — Part 6: Supplementary requirements for fuse-links for the protection of solar photovoltaic energy systems
EN 60309-1 ; Plugs, socket-outlets and couplers for industrial purposes — Part 1: General requirements
EN 60309-2 ; Plugs, socket-outlets and couplers for industrial purposes — Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
EN 60309-4 ; Plugs, socket-outlets and couplers for industrial purposes — Part 4: Switched socket-outlets and connectors with or without interlock
EN 60320-1 ; Appliance couplers for household and similar general purposes — Part 1: General requirements
EN 60320-2-1 ; Appliance couplers for household and similar general purposes — Part 2-1: Sewing machine couplers
EN 60320-2-2 ; Appliance couplers for household and similar general purposes — Part 2-2: Interconnection couplers for household and similar equipment
EN 60320-2-4 ; Appliance couplers for household and similar general purposes — Part 2-4: Appliance couplers dependent on appliance weight for engagement
EN 60332-1-1 ; Tests on electric and optical fibre cables under fire conditions — Part 1-1: Test for vertical flame propagation for a single insulated wire or cable – Apparatus
EN 60332-1-2 ; Tests on electric and optical fibre cables under fire conditions — Part 1-2: Test for vertical flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-mixed flame
EN 60332-1-3 ; Tests on electric and optical fibre cables under fire conditions — Part 1-3: Test for vertical flame propagation for a single insulated wire or cable – Procedure for determination of flaming droplets/particles
EN 60332-2-1 ; Tests on electric and optical fibre cables under fire conditions — Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable – Apparatus
EN 60332-2-2 ; Tests on electric and optical fibre cables under fire conditions — Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame
EN 60332-3-10 ; Tests on electric and optical fibre cables under fire conditions — Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables – Apparatus
EN 60332-3-21 ; Tests on electric and optical fibre cables under fire conditions — Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A F/R
EN 60332-3-22 ; Tests on electric and optical fibre cables under fire conditions — Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A
EN 60332-3-23 ; Tests on electric and optical fibre cables under fire conditions — Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category B
EN 60332-3-24 ; Tests on electric and optical fibre cables under fire conditions — Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category C
EN 60332-3-25 ; Tests on electric and optical fibre cables under fire conditions — Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category D
EN 60335-1 ; Safety of household and similar electrical appliances — Part 1: General requirements
EN 60335-2-10 ; Household and similar electrical appliances – Safety — Part 2-10: Particular requirements for floor treatment machines and wet scrubbing machines
EN 60335-2-101 ; Household and similar electrical appliances – Safety — Part 2-101: Particular requirements for vaporizers
EN 60335-2-102 ; Household and similar electrical appliances – Safety — Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
EN 60335-2-105 ; Household and similar electrical appliances – Safety — Part 2-105: Particular requirements for multifunctional shower cabinets
EN 60335-2-106 ; Household and similar electrical appliances – Safety — Part 2-106: Particular requirements for heated carpets and for heating units for room heating installed under removable floor coverings
EN 60335-2-108 ; Household and similar electrical appliances – Safety — Part 2-108: Particular requirements for electrolysers
EN 60335-2-109 ; Household and similar electrical appliances – Safety — Part 2-109: Particular requirements for UV radiation water treatment appliances
EN 60335-2-11 ; Household and similar electrical appliances – Safety — Part 2-11: Particular requirements for tumble dryers
EN 60335-2-12 ; Household and similar electrical appliances – Safety — Part 2-12: Particular requirements for warming plates and similar appliances
EN 60335-2-13 ; Household and similar electrical appliances – Safety — Part 2-13: Particular requirements for deep fat fryers, frying pans and similar appliances
EN 60335-2-14 ; Household and similar electrical appliances – Safety — Part 2-14: Particular requirements for kitchen machines
EN 60335-2-15 ; Household and similar electrical appliances – Safety — Part 2-15: Particular requirements for appliances for heating liquids
EN 60335-2-16 ; Household and similar electrical appliances – Safety — Part 2-16: Particular requirements for food waste disposers
EN 60335-2-17 ; Household and similar electrical appliances – Safety — Part 2-17: Particular requirements for blankets, pads, clothing and similar flexible heating appliances
EN 60335-2-2 ; Household and similar electrical appliances – Safety — Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances
EN 60335-2-21 ; Household and similar electrical appliances – Safety — Part 2-21: Particular requirements for storage water heaters
EN 60335-2-23 ; Household and similar electrical appliances – Safety — Part 2-23: Particular requirements for appliances for skin or hair care
EN 60335-2-24 ; Household and similar electrical appliances – Safety — Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice-makers
EN 60335-2-25 ; Household and similar electrical appliances – Safety — Part 2-25: Particular requirements for microwave ovens, including combination microwave ovens
EN 60335-2-26 ; Household and similar electrical appliances – Safety — Part 2-26: Particular requirements for clocks
EN 60335-2-27 ; Household and similar electrical appliances – Safety — Part 2-27: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation
EN 60335-2-28 ; Household and similar electrical appliances – Safety — Part 2-28: Particular requirements for sewing machines
EN 60335-2-29 ; Household and similar electrical appliances – Safety — Part 2-29: Particular requirements for battery chargers
EN 60335-2-3 ; Household and similar electrical appliances – Safety — Part 2-3: Particular requirements for electric irons
EN 60335-2-30 ; Household and similar electrical appliances – Safety — Part 2-30: Particular requirements for room heaters
EN 60335-2-31 ; Household and similar electrical appliances – Safety — Part 2-31: Particular requirements for range hoods and other cooking fume extractors
EN 60335-2-32 ; Household and similar electrical appliances – Safety — Part 2-32: Particular requirements for massage appliances
EN 60335-2-34 ; Household and similar electrical appliances – Safety — Part 2-34: Particular requirements for motor-compressors
EN 60335-2-35 ; Household and similar electrical appliances – Safety — Part 2-35: Particular requirements for instantaneous water heaters
EN 60335-2-36 ; Household and similar electrical appliances – Safety — Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements
EN 60335-2-37 ; Household and similar electrical appliances – Safety — Part 2-37: Particular requirements for commercial electric deep fat fryers
EN 60335-2-38 ; Household and similar electrical appliances – Safety — Part 2-38: Particular requirements for commercial electric griddles and griddle grills
EN 60335-2-39 ; Household and similar electrical appliances – Safety — Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans
EN 60335-2-4 ; Household and similar electrical appliances – Safety — Part 2-4: Particular requirements for spin extractors
EN 60335-2-40 ; Household and similar electrical appliances – Safety — Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
EN 60335-2-41 ; Household and similar electrical appliances – Safety — Part 2-41: Particular requirements for pumps
EN 60335-2-42 ; Household and similar electrical appliances – Safety — Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens
EN 60335-2-43 ; Household and similar electrical appliances – Safety — Part 2-43: Particular requirements for clothes dryers and towel rails
EN 60335-2-44 ; Household and similar electrical appliances – Safety — Part 2-44: Particular requirements for ironers
EN 60335-2-45 ; Household and similar electrical appliances – Safety — Part 2-45: Particular requirements for portable heating tools and similar appliances
EN 60335-2-47 ; Household and similar electrical appliances – Safety — Part 2-47: Particular requirements for commercial electric boiling pans
EN 60335-2-48 ; Household and similar electrical appliances – Safety — Part 2-48: Particular requirements for commercial electric grillers and toasters
EN 60335-2-49 ; Household and similar electrical appliances – Safety — Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm
EN 60335-2-5 ; Household and similar electrical appliances – Safety — Part 2-5: Particular requirements for dishwashers
EN 60335-2-50 ; Household and similar electrical appliances – Safety — Part 2-50: Particular requirements for commercial electric bains-marie
EN 60335-2-51 ; Household and similar electrical appliances – Safety — Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations
EN 60335-2-52 ; Household and similar electrical appliances – Safety — Part 2-52: Particular requirements for oral hygiene appliances
EN 60335-2-53 ; Household and similar electrical appliances – Safety — Part 2-53: Particular requirements for sauna heating appliances
EN 60335-2-53 ; Household and similar electrical appliances – Safety — Part 2-53: Particular requirements for sauna heating appliances and infrared cabins
EN 60335-2-54 ; Household and similar electrical appliances – Safety — Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam
EN 60335-2-54 ; Household and similar electrical appliances – Safety — Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam
EN 60335-2-55 ; Household and similar electrical appliances – Safety — Part 2-55: Particular requirements for electrical appliances for use with aquariums and garden ponds
EN 60335-2-56 ; Household and similar electrical appliances – Safety — Part 2-56: Particular requirements for projectors and similar appliances
EN 60335-2-59 ; Household and similar electrical appliances – Safety — Part 2-59: Particular requirements for insect killers
EN 60335-2-6 ; Household and similar electrical appliances – Safety — Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances
EN 60335-2-60 ; Household and similar electrical appliances – Safety — Part 2-60: Particular requirements for whirlpool baths and whirlpool spas
EN 60335-2-61 ; Household and similar electrical appliances – Safety — Part 2-61: Particular requirements for thermal-storage room heaters
EN 60335-2-62 ; Household and similar electrical appliances – Safety — Part 2-62: Particular requirements for commercial electric rinsing sinks
EN 60335-2-65 ; Household and similar electrical appliances – Safety — Part 2-65: Particular requirements for air-cleaning appliances
EN 60335-2-66 ; Household and similar electrical appliances – Safety — Part 2-66: Particular requirements for water-bed heaters
EN 60335-2-7 ; Household and similar electrical appliances – Safety — Part 2-7: Particular requirements for washing machines
EN 60335-2-71 ; Household and similar electrical appliances – Safety — Part 2-71: Particular requirements for electrical heating appliances for breeding and rearing animals
EN 60335-2-73 ; Household and similar electrical appliances – Safety — Part 2-73: Particular requirements for fixed immersion heaters
EN 60335-2-74 ; Household and similar electrical appliances – Safety — Part 2-74: Particular requirements for portable immersion heaters
EN 60335-2-75 ; Household and similar electrical appliances – Safety — Part 2-75: Particular requirements for commercial dispensing appliances and vending machines
EN 60335-2-78 ; Household and similar electrical appliances – Safety — Part 2-78: Particular requirements for outdoor barbecues
EN 60335-2-8 ; Household and similar electrical appliances – Safety — Part 2-8: Particular requirements for shavers, hair clippers and similar appliances
EN 60335-2-80 ; Household and similar electrical appliances – Safety — Part 2-80: Particular requirements for fans
EN 60335-2-81 ; Household and similar electrical appliances – Safety — Part 2-81: Particular requirements for foot warmers and heating mats
EN 60335-2-82 ; Household and similar electrical appliances – Safety — Part 2-82: Particular requirements for amusement machines and personal service machines
EN 60335-2-83 ; Household and similar electrical appliances – Safety — Part 2-83: Particular requirements for heated gullies for roof drainage
EN 60335-2-84 ; Household and similar electrical appliances – Safety — Part 2-84: Particular requirements for toilets
EN 60335-2-85 ; Household and similar electrical appliances – Safety — Part 2-85: Particular requirements for fabric steamers
EN 60335-2-86 ; Household and similar electrical appliances – Safety — Part 2-86: Particular requirements for electric fishing machines
EN 60335-2-87 ; Household and similar electrical appliances – Safety — Part 2-87: Particular requirements for electrical animal-stunning equipment
EN 60335-2-88 ; Household and similar electrical appliances – Safety — Part 2-88: Particular requirements for humidifiers intended for use with heating, ventilation, or air-conditioning systems
EN 60335-2-9 ; Household and similar electrical appliances – Safety — Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliances
EN 60335-2-90 ; Household and similar electrical appliances – Safety — Part 2-90: Particular requirements for commercial microwave ovens
EN 60335-2-96 ; Household and similar electrical appliances – Safety — Part 2-96: Particular requirements for flexible sheet heating elements for room heating
EN 60335-2-97 ; Household and similar electrical appliances – Safety — Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment
EN 60335-2-98 ; Household and similar electrical appliances – Safety — Part 2-98: Particular requirements for humidifiers
EN 60358-1 ; Coupling capacitors and capacitor dividers — Part 1: General rules
EN 60360 ; Standard method of measurement of lamp cap temperature rise
EN 60399 ; Barrel thread for lampholders with shade holder ring
EN 60400 ; Lampholders for tubular fluorescent lamps and starterholders
EN 60423 ; Conduit systems for cable management – Outside diameters of conduits for electrical installations and threads for conduits and fittings
EN 60432-1 ; Incandescent lamps – Safety specifications — Part 1: Tungsten filament lamps for domestic and similar general lighting purposes
EN 60432-2 ; Incandescent lamps – Safety specifications — Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes
EN 60432-3 ; Incandescent lamps – Safety specifications — Part 3: Tungsten-halogen lamps (non-vehicle)
EN 60432-3 ; Incandescent lamps – Safety specifications — Part 3: Tungsten-halogen lamps (non-vehicle)
EN 60439-1 ; Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially type-tested assemblies
EN 60439-2 ; Low-voltage switchgear and controlgear assemblies — Part 2: Particular requirements for busbar trunking systems (busways)
EN 60439-3 ; Low-voltage switchgear and controlgear assemblies — Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use – Distribution boards
EN 60439-4 ; Low-voltage switchgear and controlgear assemblies — Part 4: Particular requirements for assemblies for construction sites (ACS)
EN 60439-5 ; Low-voltage switchgear and controlgear assemblies — Part 5: Particular requirements for assemblies for power distribution in public networks
EN 60446 ; Basic and safety principles for man-machine interface, marking and identification – Identification of conductors by colours or alphanumerics
EN 60477 ; Laboratory d.c. resistors
EN 60477-2 ; Laboratory resistors — Part 2: Laboratory a.c. resistors
EN 60519-1 ; Safety in electroheating installations — Part 1: General requirements
EN 60519-10 ; Safety in electroheat installations — Part 10: Particular requirements for electrical resistance trace heating systems for industrial and commercial applications
EN 60519-2 ; Safety in electroheat installations — Part 2: Particular requirements for resistance heating equipment
EN 60519-21 ; Safety in electroheat installations — Part 21: Particular requirements for resistance heating equipment – Heating and melting glass equipment
EN 60519-3 ; Safety in electroheat installations — Part 3: Particular requirements for induction and conduction heating and induction melting installations
EN 60519-4 ; Safety in electroheat installations — Part 4: Particular requirements for arc furnace installations
EN 60519-6 ; Safety in electroheat installations — Part 6: Specifications for safety in industrial microwave heating equipment
EN 60519-6 ; Safety in electroheat installations — Part 6: Specifications for safety in industrial microwave heating equipment
EN 60519-7 ; Safety in electroheat installations — Part 7: Particular requirements for installations with electron guns
EN 60519-8 ; Safety in electroheat installations — Part 8: Particular requirements for electroslag remelting furnaces
EN 60519-9 ; Safety in electroheat installations — Part 9: Particular requirements for high-frequency dielectric heating installations
EN 60523 ; Direct-current potentiometers
EN 60524 ; Direct-current resistive volt ratio boxes
EN 60529 ; Degrees of protection provided by enclosures (IP Code)
EN 60564 ; D.C. bridges for measuring resistance
EN 60570 ; Electrical supply track systems for luminaires
EN 60598-1 ; Luminaires — Part 1: General requirements and tests
EN 60598-2-1 ; Luminaires — Part 2: Particular requirements — Section 1: Fixed general purpose luminaires
EN 60598-2-10 ; Luminaires — Part 2-10: Particular requirements – Portable luminaires for children
EN 60598-2-11 ; Luminaires — Part 2-11: Particular requirements – Aquarium luminaires
EN 60598-2-12 ; Luminaires — Part 2-12: Particular requirements – Mains socket-outlet mounted nightlights
EN 60598-2-13 ; Luminaires — Part 2-13: Particular requirements – Ground recessed luminaires
EN 60598-2-14 ; Luminaires — Part 2-14: Particular requirements – Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment
EN 60598-2-17 ; Luminaires — Part 2: Particular requirements — Section 17: Luminaires for stage lighting, television film and photographic studios (outdoor and indoor)
EN 60598-2-19 ; Luminaires — Part 2: Particular requirements — Section 19: Air-handling luminaires (safety requirements)
EN 60598-2-2 ; Luminaires — Part 2: Particular requirements — Section 2: Recessed luminaires
EN 60598-2-20 ; Luminaires — Part 2-20: Particular requirements – Lighting chains
EN 60598-2-20 ; Luminaires — Part 2-20: Particular requirements – Lighting chains
EN 60598-2-22 ; Luminaires — Part 2-22: Particular requirements – Luminaires for emergency lighting
EN 60598-2-23 ; Luminaires — Part 2-23: Particular requirements – Extra low-voltage lighting systems for filament lamps
EN 60598-2-24 ; Luminaires — Part 2: Particular requirements — Section 24: Luminaires with limited surface temperatures
EN 60598-2-25 ; Luminaires — Part 2-25: Particular requirements – Luminaires for use in clinical areas of hospitals and health care buildings
EN 60598-2-3 ; Luminaires — Part 2-3: Particular requirements – Luminaires for road and street lighting
EN 60598-2-4 ; Luminaires — Part 2: Particular requirements — Section 4: Portable general purpose luminaires
EN 60598-2-5 ; Luminaires — Part 2-5: Particular requirements – Floodlights
EN 60598-2-6 ; Luminaires — Part 2: Particular requirements — Section 6: Luminaires with built-in transformers or convertors for filament lamps
EN 60598-2-7 ; Luminaires — Part 2: Particular requirements — Section 7: Portable luminaires for garden use
EN 60598-2-8 ; Luminaires — Part 2-8: Particular requirements – Handlamps
EN 60598-2-9 ; Luminaires — Part 2: Particular requirements — Section 9: Photo and film luminaires (non-professional)
EN 60618 ; Inductive voltage dividers
EN 60645-1 ; Electroacoustics – Audiological equipment — Part 1: Pure-tone audiometers
EN 60645-3 ; Electroacoustics – Audiometric equipment — Part 3: Test signals of short duration
EN 60645-4 ; Audiometers — Part 4: Equipment for extended high-frequency audiometry
EN 60645-6 ; Electroacoustics – Audiometric equipment — Part 6: Instruments for the measurement of otoacoustic emissions
EN 60645-7 ; Electroacoustics – Audiometric equipment — Part 7: Instruments for the measurement of auditory brainstem responses
EN 60662 ; High-pressure sodium vapour lamps
EN 60664-1 ; Insulation coordination for equipment within low-voltage systems — Part 1: Principles, requirements and tests
EN 60664-3 ; Insulation coordination for equipment within low-voltage systems — Part 3: Use of coating, potting or moulding for protection against pollution
EN 60664-4 ; Insulation coordination for equipment within low-voltage systems — Part 4: Consideration of high-frequency voltage stress
EN 60664-5 ; Insulation coordination for equipment within low-voltage systems — Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
EN 60669-1 ; Switches for household and similar fixed-electrical installations — Part 1: General requirements
EN 60669-2-1 ; Switches for household and similar fixed electrical installations — Part 2-1: Particular requirements – Electronic switches
EN 60669-2-2 ; Switches for household and similar fixed electrical installations — Part 2-2: Particular requirements – Electromagnetic remote-control switches (RCS)
EN 60669-2-3 ; Switches for household and similar fixed electrical installations — Part 2-3: Particular requirements – Time delay switches (TDS)
EN 60669-2-4 ; Switches for household and similar fixed electrical installations — Part 2-4: Particular requirements – Isolating switches
EN 60669-2-6 ; Switches for household and similar fixed electrical installations — Part 2-6: Particular requirements – Fireman’s switches for exterior and interior signs and luminaires
EN 60670-1 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 1: General requirements
EN 60670-21 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 21: Particular requirements for boxes and enclosures with provision for suspension means
EN 60670-22 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 22: Particular requirements for connecting boxes and enclosures
EN 60670-23 ; Boxes and enclosures for electrical accessories for household and similar fixed electrical installations — Part 23: Particular requirements for floor boxes and enclosures
EN 60688 ; Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
EN 60691 ; Thermal-links – Requirements and application guide
EN 60695-10-2 ; Fire hazard testing — Part 10-2: Abnormal heat – Ball pressure test
EN 60695-10-3 ; Fire hazard testing — Part 10-3: Abnormal heat – Mould stress relief distortion test
EN 60695-1-1 ; Fire hazard testing — Part 1-1: Guidance for assessing the fire hazard of electrotechnical products – General guidelines
EN 60695-11-10 ; Fire hazard testing — Part 11-10: Test flames – 50 W horizontal and vertical flame test methods
EN 60695-11-2 ; Fire hazard testing — Part 11-2: Test flames – 1 kW nominal pre-mixed flame – Apparatus, confirmatory test arrangement and guidance
EN 60695-11-20 ; Fire hazard testing — Part 11-20: Test flames – 500 W flame test methods
EN 60695-11-3 ; Fire hazard testing — Part 11-3: Test flames – 500 W flames – Apparatus and confirmational test methods
EN 60695-11-4 ; Fire hazard testing — Part 11-4: Test flames – 50 W flame – Apparatus and confirmational test method
EN 60695-11-5 ; Fire hazard testing — Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory test arrangement and guidance
EN 60695-2-10 ; Fire hazard testing — Part 2-10: Glowing/hot-wire based test methods – Glow-wire apparatus and common test procedure
EN 60695-2-11 ; Fire hazard testing — Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test method for end-products
EN 60695-2-12 ; Fire hazard testing — Part 2-12: Glowing/hot-wire based test methods – Glow-wire flammability test method for materials
EN 60695-2-13 ; Fire hazard testing — Part 2-13: Glowing/hot-wire based test methods – Glow-wire ignitability test method for materials
EN 60702-1 ; Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V — Part 1: Cables
EN 60702-2 ; Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V — Part 2: Terminations
EN 60715 ; Dimensions of low-voltage switchgear and controlgear – Standardized mounting on rails for mechanical support of electrical devices in switchgear and controlgear installations
EN 60719 ; Calculation of the lower and upper limits for the average outer dimensions of cables with circular copper conductors and of rated voltages up to and including 450/750 V
EN 60728-11 ; Cable networks for television signals, sound signals and interactive services — Part 11: Safety
EN 60728-11 ; Cable networks for television signals, sound signals and interactive services — Part 11: Safety
EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
EN 60730-1 ; Automatic electrical controls for household and similar use — Part 1: General requirements
EN 60730-2-10 ; Automatic electrical controls for household and similar use — Part 2-10: Particular requirements for motor-starting relays
EN 60730-2-11 ; Automatic electrical controls for household and similar use — Part 2-11: Particular requirements for energy regulators
EN 60730-2-12 ; Automatic electrical controls for household and similar use — Part 2-12: Particular requirements for electrically operated door locks
EN 60730-2-13 ; Automatic electrical controls for household and similar use — Part 2-13: Particular requirements for humidity sensing controls
EN 60730-2-14 ; Automatic electrical controls for household and similar use — Part 2-14: Particular requirements for electric actuators
EN 60730-2-15 ; Automatic electrical controls for household and similar use — Part 2-15: Particular requirements for automatic electrical air flow, water flow and water level sensing controls
EN 60730-2-19 ; Automatic electrical controls for household and similar use — Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements
EN 60730-2-2 ; Automatic electrical controls for household and similar use — Part 2-2: Particular requirements for thermal motor protectors
EN 60730-2-3 ; Automatic electrical controls for household and similar use — Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps
EN 60730-2-4 ; Automatic electrical controls for household and similar use — Part 2-4: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type
EN 60730-2-5 ; Automatic electrical controls for household and similar use — Part 2-5: Particular requirements for automatic electrical burner control systems
EN 60730-2-6 ; Automatic electrical controls for household and similar use — Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements
EN 60730-2-7 ; Automatic electrical controls for household and similar use — Part 2-7: Particular requirements for timers and time switches
EN 60730-2-8 ; Automatic electrical controls for household and similar use — Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements
EN 60730-2-9 ; Automatic electrical controls for household and similar use — Part 2-9: Particular requirements for temperature sensing controls
EN 60799 ; Electrical accessories – Cord sets and interconnection cord sets
EN 60811-100 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 100: General
EN 60811-1-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 1-1: General application – Measurement of thickness and overall dimensions – Tests for determining the mechanical properties
EN 60811-1-2 ; Insulating and sheathing materials of electric cables – Common test methods — Part 1-2: General application – Thermal ageing methods
EN 60811-1-3 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 1-3: General application – Methods for determining the density – Water absorption tests – Shrinkage test
EN 60811-1-4 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 1-4: General application – Tests at low temperature
EN 60811-201 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 201: General tests – Measurement of insulation thickness
EN 60811-202 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 202: General tests – Measurement of thickness of non-metallic sheath
EN 60811-203 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 203: General tests – Measurement of overall dimensions
EN 60811-2-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 2-1: Methods specific to elastomeric compounds – Ozone resistance, hot set and mineral oil immersion tests
EN 60811-301 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 301: Electrical tests – Measurement of the permittivity at 23 °C of filling compounds
EN 60811-302 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 302: Electrical tests – Measurement of the d.c. resistivity at 23 °C and 100 °C of filling compounds
EN 60811-3-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 3-1: Methods specific to PVC compounds – Pressure test at high temperature – Tests for resistance to cracking
EN 60811-3-2 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 3-2: Methods specific to PVC compounds – Loss of mass test – Thermal stability test
EN 60811-401 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 401: Miscellaneous tests – Thermal ageing methods – Ageing in an air oven
EN 60811-402 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 402: Miscellaneous tests – Water absorption tests
EN 60811-403 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 403: Miscellaneous tests – Ozone resistance test on cross-linked compounds
EN 60811-404 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 404: Miscellaneous tests – Mineral oil immersion tests for sheaths
EN 60811-405 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 405: Miscellaneous tests – Thermal stability test for PVC insulations and PVC sheaths
EN 60811-406 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 406: Miscellaneous tests – Resistance to stress cracking of polyethylene and polypropylene compounds
EN 60811-407 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 407: Miscellaneous tests – Measurement of mass increase of polyethylene and polypropylene compounds
EN 60811-408 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 408: Miscellaneous tests – Long-term stability test of polyethylene and polypropylene compounds
EN 60811-409 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 409: Miscellaneous tests – Loss of mass test for thermoplastic insulations and sheaths
EN 60811-4-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 4-1: Methods specific to polyethylene and polypropylene compounds – Resistance to environmental stress cracking – Measurement of the melt flow index – Carbon black and/or mineral filler content measurement in polyethylene by direct combustion – Measurement of carbon black content by thermogravimetric analysis (TGA) – Assessment of carbon black dispersion in polyethylene using a microscope
EN 60811-410 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 410: Miscellaneous tests – Test method for copper-catalyzed oxidative degradation of polyolefin insulated conductors
EN 60811-411 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 411: Miscellaneous tests – Low-temperature brittleness of filling compounds
EN 60811-412 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 412: Miscellaneous tests – Thermal ageing methods – Ageing in an air bomb
EN 60811-4-2 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 4-2: Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature – Wrapping test after conditioning at elevated temperature – Wrapping test after thermal ageing in air – Measurement of mass increase – Long-term stability test – Test method for copper-catalyzed oxidative degradation
EN 60811-501 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 501: Mechanical tests – Tests for determining the mechanical properties of insulating and sheathing compounds
EN 60811-502 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 502: Mechanical tests – Shrinkage test for insulations
EN 60811-503 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 503: Mechanical tests – Shrinkage test for sheaths
EN 60811-504 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 504: Mechanical tests – Bending tests at low temperature for insulation and sheaths
EN 60811-505 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 505: Mechanical tests – Elongation at low temperature for insulations and sheaths
EN 60811-506 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 506: Mechanical tests – Impact test at low temperature for insulations and sheaths
EN 60811-507 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 507: Mechanical tests – Hot set test for cross-linked materials
EN 60811-508 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 508: Mechanical tests – Pressure test at high temperature for insulation and sheaths
EN 60811-509 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 509: Mechanical tests – Test for resistance of insulations and sheaths to cracking (heat shock test)
EN 60811-5-1 ; Insulating and sheathing materials of electric and optical cables – Common test methods — Part 5-1: Methods specific to filling compounds – Drop point – Separation of oil – Lower temperature brittleness – Total acid number – Absence of corrosive components – Permittivity at 23 °C – D.C. resistivity at 23 °C and 100 °C
EN 60811-510 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 510: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after thermal ageing in air
EN 60811-511 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 511: Mechanical tests – Measurement of the melt flow index of polyethylene compounds
EN 60811-512 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 512: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature
EN 60811-513 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 513: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after conditioning
EN 60811-601 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 601: Physical tests – Measurement of the drop point of filling compounds
EN 60811-602 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 602: Physical tests – Separation of oil in filling compounds
EN 60811-603 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 603: Physical tests – Measurement of total acid number of filling compounds
EN 60811-604 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 604: Physical tests – Measurement of absence of corrosive components in filling compounds
EN 60811-605 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 605: Physical tests – Measurement of carbon black and/or mineral filler in polyethylene compounds
EN 60811-606 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 606: Physical tests – Methods for determining the density
EN 60811-607 ; Electric and optical fibre cables – Test methods for non-metallic materials — Part 607: Physical tests – Test for the assessment of carbon black dispersion in polyethylene and polypropylene
EN 60825-1 ; Safety of laser products — Part 1: Equipment classification and requirements
EN 60825-12 ; Safety of laser products — Part 12: Safety of free space optical communication systems used for transmission of information
EN 60825-2 ; Safety of laser products — Part 2: Safety of optical fibre communication systems (OFCS)
EN 60825-4 ; Safety of laser products — Part 4: Laser guards
EN 60831-1 ; Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
EN 60831-2 ; Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 2: Ageing test, self-healing test and destruction test
EN 60838-1 ; Miscellaneous lampholders — Part 1: General requirements and tests
EN 60838-2-1 ; Miscellaneous lampholders — Part 2: Particular requirements — Section 1: Lampholders S14
EN 60838-2-2 ; Miscellaneous lampholders — Part 2-2: Particular requirements – Connectors for LED-modules
EN 60898-1 ; Electrical accessories – Circuit breakers for overcurrent protection for household and similar installations — Part 1: Circuit-breakers for a.c. operation
EN 60898-2 ; Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations — Part 2: Circuit-breakers for a.c. and d.c. operation
EN 60931-1 ; Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
EN 60931-2 ; Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 2: Ageing test and destruction test
EN 60931-3 ; Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV — Part 3: Internal fuses
EN 60934 ; Circuit-breakers for equipment (CBE)
EN 60947-1 ; Low-voltage switchgear and controlgear — Part 1: General rules
EN 60947-2 ; Low-voltage switchgear and controlgear — Part 2: Circuit-breakers
EN 60947-3 ; Low-voltage switchgear and controlgear — Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
EN 60947-4-1 ; Low-voltage switchgear and controlgear — Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters
EN 60947-4-1 ; Low-voltage switchgear and controlgear — Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters
EN 60947-4-2 ; Low-voltage switchgear and controlgear — Part 4-2: Contactors and motor-starters – AC semiconductor motor controllers and starters
EN 60947-4-2 ; Low-voltage switchgear and controlgear — Part 4-2: Contactors and motor-starters – AC semiconductor motor controllers and starters
EN 60947-4-3 ; Low-voltage switchgear and controlgear — Part 4-3: Contactors and motor-starters – AC semiconductor controllers and contactors for non-motor loads
EN 60947-5-1 ; Low-voltage switchgear and controlgear — Part 5-1: Control circuit devices and switching elements – Electromechanical control circuit devices
EN 60947-5-2 ; Low-voltage switchgear and controlgear — Part 5-2: Control circuit devices and switching elements – Proximity switches
EN 60947-5-3 ; Low-voltage switchgear and controlgear — Part 5-3: Control circuit devices and switching elements – Requirements for proximity devices with defined behaviour under fault conditions (PDF)
EN 60947-5-4 ; Low-voltage switchgear and controlgear — Part 5-4: Control circuit devices and switching elements – Method of assessing the performance of low-energy contacts – Special tests
EN 60947-5-5 ; Low-voltage switchgear and controlgear — Part 5-5: Control circuit devices and switching elements – Electrical emergency stop device with mechanical latching function
EN 60947-5-7 ; Low-voltage switchgear and controlgear — Part 5-7: Control circuit devices and switching elements – Requirements for proximity devices with analogue output
EN 60947-5-8 ; Low-voltage switchgear and controlgear — Part 5-8: Control circuit devices and switching elements – Three-position enabling switches
EN 60947-5-9 ; Low-voltage switchgear and controlgear — Part 5-9: Control circuit devices and switching elements – Flow rate switches
EN 60947-6-1 ; Low-voltage switchgear and controlgear — Part 6-1: Multiple function equipment – Transfer switching equipment
EN 60947-6-2 ; Low-voltage switchgear and controlgear — Part 6-2: Multiple function equipment – Control and protective switching devices (or equipment) (CPS)
EN 60947-7-1 ; Low-voltage switchgear and controlgear — Part 7-1: Ancillary equipment – Terminal blocks for copper conductors
EN 60947-7-2 ; Low-voltage switchgear and controlgear — Part 7-2: Ancillary equipment – Protective conductor terminal blocks for copper conductors
EN 60947-7-3 ; Low-voltage switchgear and controlgear — Part 7-3: Ancillary equipment – Safety requirements for fuse terminal blocks
EN 60947-8 ; Low-voltage switchgear and controlgear — Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines
EN 60950-1 ; Information technology equipment – Safety — Part 1: General requirements
EN 60950-21 ; Information technology equipment – Safety — Part 21: Remote power feeding
EN 60950-22 ; Information technology equipment – Safety — Part 22: Equipment installed outdoors
EN 60950-23 ; Information technology equipment – Safety — Part 23: Large data storage equipment
EN 60968 ; Self-ballasted lamps for general lighting services – Safety requirements
EN 60968 ; Self-ballasted lamps for general lighting services – Safety requirements
EN 60974-1 ; Arc welding equipment — Part 1: Welding power sources
EN 60974-1 ; Arc welding equipment — Part 1: Welding power sources
EN 60974-11 ; Arc welding equipment — Part 11: Electrode holders
EN 60974-11 ; Arc welding equipment — Part 11: Electrode holders
EN 60974-12 ; Arc welding equipment — Part 12: Coupling devices for welding cables
EN 60974-12 ; Arc welding equipment — Part 12: Coupling devices for welding cables
EN 60974-13 ; Arc welding equipment — Part 13: Welding clamp
EN 60974-2 ; Arc welding equipment — Part 2: Liquid cooling systems
EN 60974-3 ; Arc welding equipment — Part 3: Arc striking and stabilizing devices
EN 60974-5 ; Arc welding equipment — Part 5: Wire feeders
EN 60974-6 ; Arc welding equipment — Part 6: Limited duty equipment
EN 60974-6 ; Arc welding equipment — Part 6: Limited duty manual metal arc welding power sources
EN 60974-7 ; Arc welding equipment — Part 7:Torches
EN 60974-8 ; Arc welding equipment — Part 8: Gas consoles for welding and plasma cutting systems
EN 60998-1 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 1: General requirements
EN 60998-2-1 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units
EN 60998-2-2 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
EN 60998-2-3 ; Connecting devices for low-voltage circuits for household and similar purposes — Part 2-3: Particular requirements for connecting devices as separate entities with insulation-piercing clamping units
EN 60998-2-4 ; Connecting devices for low voltage circuits for household and similar purposes — Part 2-4: Particular requirements for twist-on connecting devices
EN 60999-1 ; Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units — Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included)
EN 60999-2 ; Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units — Part 2: Particular requirements for clamping units for conductors above 35 mm² up to 300 mm² (included)
EN 61008-1 ; Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) — Part 1: General rules
EN 61008-1 ; Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) — Part 1: General rules
EN 61008-2-1 ; Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) — Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage
EN 61009-1 ; Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) — Part 1: General rules
EN 61009-1 ; Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO’s) — Part 1: General rules
EN 61009-2-1 ; Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO’s) — Part 2-1: Applicability of the general rules to RCBO’s functionally independent of line voltage
EN 61010-031 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test
EN 61010-1 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 1: General requirements
EN 61010-1 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 1: General requirements
EN 61010-2-010 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-010: Particular requirements for laboratory equipment for the heating of material
EN 61010-2-020 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-020: Particular requirements for laboratory centrifuges
EN 61010-2-030 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-030: Particular requirements for testing and measuring circuits
EN 61010-2-032 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement
EN 61010-2-032 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement
EN 61010-2-033 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-033: Particular requirements for hand-held multimeters and other meters, for domestic and professional use, capable of measuring mains voltage
EN 61010-2-040 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials
EN 61010-2-051 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-051: Particular requirements for laboratory equipment for mixing and stirring
EN 61010-2-061 ; Safety requirements for electrical equipment for measurement, control, and laboratory use — Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization
EN 61010-2-081 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
EN 61010-2-091 ; Safety requirements for electrical equipment for measurement, control and laboratory use — Part 2-091: Particular requirements for cabinet X-ray systems
EN 61028 ; Electrical measuring instruments – X-Y recorders
EN 61034-1 ; Measurement of smoke density of cables burning under defined conditions — Part 1: Test apparatus
EN 61034-2 ; Measurement of smoke density of cables burning under defined conditions — Part 2: Test procedure and requirements
EN 61048 ; Auxiliaries for lamps – Capacitors for use in tubular fluorescent and other discharge lamp circuits – General and safety requirements
EN 61050 ; Transformers for tubular discharge lamps having a no-load output voltage exceeding 1 kV (generally called neon-transformers) – General and safety requirements
EN 61058-1 ; Switches for appliances — Part 1: General requirements
EN 61058-2-1 ; Switches for appliances — Part 2-1: Particular requirements for cord switches
EN 61058-2-1 ; Switches for appliances — Part 2-1: Particular requirements for cord switches
EN 61058-2-4 ; Switches for appliances — Part 2-4: Particular requirements for independently mounted switches
EN 61058-2-5 ; Switches for appliances — Part 2-5: Particular requirements for change-over selectors
EN 61058-2-5 ; Switches for appliances — Part 2-5: Particular requirements for change-over selectors
EN 61071 ; Capacitors for power electronics
EN 61095 ; Electromechanical contactors for household and similar purposes
EN 61131-2 ; Programmable controllers — Part 2: Equipment requirements and tests
EN 61138 ; Cables for portable earthing and short-circuiting equipment
EN 61140 ; Protection against electric shock – Common aspects for installation and equipment
EN 61143-1 ; Electrical measuring instruments – X-t recorders — Part 1: Definitions and requirements
EN 61143-2 ; Electrical measuring instruments – X-t recorders — Part 2: Recommended additional test methods
EN 61167 ; Metal halide lamps
EN 61184 ; Bayonet lampholders
EN 61187 ; Electrical and electronic measuring equipment – Documentation
EN 61195 ; Double-capped fluorescent lamps – Safety specifications
EN 61199 ; Single-capped fluorescent lamps – Safety specifications
EN 61199 ; Single-capped fluorescent lamps – Safety specifications
EN 61204 ; Low-voltage power supply devices, d.c. output – Performance characteristics
EN 61204-7 ; Low voltage power supplies, d.c. output — Part 7: Safety requirements
EN 61210 ; Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements
EN 61210 ; Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements
EN 61230 ; Live working – Portable equipment for earthing or earthing and short-circuiting
EN 61236 ; Saddles, pole clamps (stick clamps) and accessories for live working
EN 61242 ; Electrical accessories – Cable reels for household and similar purposes
EN 61243-3 ; Live working – Voltage detectors — Part 3: Two-pole low-voltage type
EN 61243-3 ; Live working – Voltage detectors — Part 3: Two-pole low-voltage type
EN 61270-1 ; Capacitors for microwave ovens — Part 1: General
EN 61293 ; Marking of electrical equipment with ratings related to electrical supply – Safety requirements
EN 61310-1 ; Safety of machinery – Indication, marking and actuation — Part 1: Requirements for visual, acoustic and tactile signals
EN 61310-2 ; Safety of machinery – Indication, marking and actuation — Part 2: Requirements for marking
EN 61310-3 ; Safety of machinery – Indication, marking and actuation — Part 3: Requirements for the location and operation of actuators
EN 61316 ; Industrial cable reels
EN 61347-1 ; Lamp controlgear — Part 1: General and safety requirements
EN 61347-2-10 ; Lamp controlgear — Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes)
EN 61347-2-11 ; Lamp controlgear — Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires
EN 61347-2-12 ; Lamp controlgear — Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)
EN 61347-2-13 ; Lamp controlgear — Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules
EN 61347-2-2 ; Lamp controlgear — Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
EN 61347-2-2 ; Lamp controlgear — Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
EN 61347-2-3 ; Lamp control gear — Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps
EN 61347-2-3 ; Lamp controlgear — Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps
EN 61347-2-4 ; Lamp controlgear — Part 2-4: Particular requirements for d.c. supplied electronic ballasts for general lighting
EN 61347-2-7 ; Lamp controlgear — Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)
EN 61347-2-7 ; Lamp controlgear — Part 2-7: Particular requirements for d.c. supplied electronic ballasts for emergency lighting
EN 61347-2-8 ; Lamp controlgear — Part 2-8: Particular requirements for ballasts for fluorescent lamps
EN 61347-2-9 ; Lamp controlgear — Part 2-9: Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps)
EN 61347-2-9 ; Lamp controlgear — Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
EN 61386-1 ; Conduit systems for cable management — Part 1: General requirements
EN 61386-21 ; Conduit systems for cable management — Part 21: Particular requirements – Rigid conduit systems
EN 61386-22 ; Conduit systems for cable management — Part 22: Particular requirements – Pliable conduit systems
EN 61386-23 ; Conduit systems for cable management — Part 23: Particular requirements – Flexible conduit systems
EN 61386-24 ; Conduit systems for cable management — Part 24: Particular requirements – Conduit systems buried underground
EN 61386-25 ; Conduit systems for cable management — Part 25: Particular requirements – Conduit fixing devices
EN 61439-1 ; Low-voltage switchgear and controlgear assemblies — Part 1: General rules
EN 61439-1 ; Low-voltage switchgear and controlgear assemblies — Part 1: General rules
EN 61439-2 ; Low-voltage switchgear and controlgear assemblies — Part 2: Power switchgear and controlgear assemblies
EN 61439-2 ; Low-voltage switchgear and controlgear assemblies — Part 2: Power switchgear and controlgear assemblies
EN 61439-3 ; Low-voltage switchgear and controlgear assemblies — Part 3: Distribution boards intended to be operated by ordinary persons (DBO)
EN 61439-4 ; Low-voltage switchgear and controlgear assemblies — Part 4: Particular requirements for assemblies for construction sites (ACS)
EN 61439-5 ; Low-voltage switchgear and controlgear assemblies — Part 5: Assemblies for power distribution in public networks
EN 61439-6 ; Low-voltage switchgear and controlgear assemblies — Part 6: Busbar trunking systems (busways)
EN 61534-1 ; Powertrack systems — Part 1: General requirements
EN 61534-1 ; Powertrack systems — Part 1: General requirements
EN 61534-21 ; Powertrack systems — Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting
EN 61534-22 ; Powertrack systems — Part 22: Particular requirements for powertrack systems intended for on floor or under floor installation
EN 61535 ; Installation couplers intended for permanent connection in fixed installations
EN 61537 ; Cable management – Cable tray systems and cable ladder systems
EN 61549 ; Miscellaneous lamps
EN 61557-1 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 1: General requirements
EN 61557-10 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 10: Combined measuring equipment for testing, measuring or monitoring of protective measures
EN 61557-11 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 11: Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and IT systems
EN 61557-12 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 12: Performance measuring and monitoring devices (PMD)
EN 61557-13 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems
EN 61557-2 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 2: Insulation resistance
EN 61557-3 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 3: Loop impedance
EN 61557-4 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 4: Resistance of earth connection and equipotential bonding
EN 61557-5 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 5: Resistance to earth
EN 61557-6 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems
EN 61557-7 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 7: Phase sequence
EN 61557-8 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 8: Insulation monitoring devices for IT systems
EN 61557-9 ; Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures — Part 9: Equipment for insulation fault location in IT systems
EN 61558-1 ; Safety of power transformers, power supplies, reactors and similar products — Part 1: General requirements and tests
EN 61558-1 ; Safety of power transformers, power supply units and similar — Part 1: General requirements and tests
EN 61558-2-1 ; Safety of power transformers, power supplies, reactors and similar products — Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications
EN 61558-2-12 ; Safety of power transformers, power supply units and similar devices — Part 2-12: Particular requirements for constant voltage transformers
EN 61558-2-12 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage
EN 61558-2-13 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers
EN 61558-2-14 ; Safety of transformers, reactors, power supply units and combination thereof — Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers
EN 61558-2-15 ; Safety of power transformers, power supply units and similar — Part 2-15: Particular requirements for isolating transformers for the supply of medical locations
EN 61558-2-15 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations
EN 61558-2-16 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units
EN 61558-2-2 ; Safety of power transformers, power supplies, reactors and similar products — Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers
EN 61558-2-20 ; Safety of power transformers, power supply units and similar devices — Part 2-20: Particular requirements for small reactors
EN 61558-2-20 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-20: Particular requirements and tests for small reactors
EN 61558-2-23 ; Safety of power transformers, power supply units and similar devices — Part 2-23: Particular requirements for transformers for construction sites
EN 61558-2-23 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-23: Particular requirements and tests for transformers and power supply units for construction sites
EN 61558-2-3 ; Safety of power transformers, power supply units and similar devices — Part 2-3: Particular requirements for ignition transformers for gas and oil burners
EN 61558-2-3 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-3: Particular requirements and tests for ignition transformers for gas and oil burners
EN 61558-2-4 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers
EN 61558-2-5 ; Safety of power transformers, power supply units and similar — Part 2-5: Particular requirements for shaver transformers and shaver supply units
EN 61558-2-5 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-5: Particular requirements and tests for transformer for shavers, power supply units for shavers and shaver supply units
EN 61558-2-6 ; Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V — Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
EN 61558-2-7 ; Safety of power transformers, power supplies, reactors and similar products — Part 2-7: Particular requirements and tests for transformers and power supplies for toys
EN 61558-2-8 ; Safety of power transformers, power supply units and similar — Part 2-8: Particular requirements for bell and chime transformers
EN 61558-2-8 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-8: Particular requirements and tests for transformers and power supply units for bells and chimes
EN 61558-2-9 ; Safety of power transformers, power supply units and similar products — Part 2-9: Particular requirements for transformers for class III handlamps for tungsten filament lamps
EN 61558-2-9 ; Safety of transformers, reactors, power supply units and combinations thereof — Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps
EN 61643-11 ; Low-voltage surge protective devices — Part 11: Surge protective devices connected to low-voltage power systems – Requirements and test methods
EN 61643-11 ; Low-voltage surge protective devices — Part 11: Surge protective devices connected to low-voltage power systems – Requirements and tests
EN 61643-21 ; Low voltage surge protective devices — Part 21: Surge protective devices connected to telecommunications and signalling networks – Performance requirements and testing methods
EN 61730-1 ; Photovoltaic (PV) module safety qualification — Part 1: Requirements for construction
EN 61730-2 ; Photovoltaic (PV) module safety qualification — Part 2: Requirements for testing
EN 61770 ; Electric appliances connected to the water mains – Avoidance of backsiphonage and failure of hose-sets
EN 61800-5-1 ; Adjustable speed electrical power drive systems — Part 5-1: Safety requirements – Electrical, thermal and energy
EN 61812-1 ; Specified time relays for industrial use — Part 1: Requirements and tests
EN 61812-1 ; Time relays for industrial and residential use — Part 1: Requirements and tests
EN 61851-1 ; Electric vehicle conductive charging system — Part 1: General requirements
EN 61851-1 ; Electric vehicle conductive charging system — Part 1: General requirements
EN 61851-21 ; Electric vehicle conductive charging system — Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply
EN 61851-22 ; Electric vehicle conductive charging system — Part 22: AC electric vehicle charging station
EN 61869-1 ; Instrument transformers — Part 1: General requirements
EN 61869-2 ; Instrument transformers — Part 2: Additional requirements for current transformers
EN 61869-3 ; Instrument transformers — Part 3: Additional requirements for inductive voltage transformers
EN 61869-5 ; Instrument transformers — Part 5: Additional requirements for capacitor voltage transformers
EN 61914 ; Cable cleats for electrical installations
EN 61921 ; Power capacitors – Low-voltage power factor correction banks
EN 61995-1 ; Devices for the connection of luminaires for household and similar purposes — Part 1: General requirements
EN 61995-2 ; Devices for the connection of luminaires for household and similar purposes — Part 2: Standard sheets for DCL
EN 62020 ; Electrical accessories – Residual current monitors for household and similar uses (RCMs)
EN 62026-1 ; Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) — Part 1: General rules
EN 62026-3 ; Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) — Part 3: DeviceNet
EN 62031 ; LED modules for general lighting – Safety specifications
EN 62035 ; Discharge lamps (excluding fluorescent lamps) – Safety specifications
EN 62040-1 ; Uninterruptible power systems (UPS) — Part 1: General and safety requirements for UPS
EN 62080 ; Sound signalling devices for household and similar purposes
EN 62094-1 ; Indicator light units for household and similar fixed-electrical installations — Part 1: General requirements
EN 62109-1 ; Safety of power converters for use in photovoltaic power systems — Part 1: General requirements
EN 62109-2 ; Safety of power converters for use in photovoltaic power systems — Part 2: Particular requirements for inverters
EN 62135-1 ; Resistance welding equipment — Part 1: Safety requirements for design, manufacture and installation
EN 62196-1 ; Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles — Part 1: General requirements
EN 62196-1 ; Plugs, socket-outlets, vehicle couplers and vehicle inlets – Conductive charging of electric vehicles — Part 1: Charging of electric vehicles up to 250 A a.c. and 400 A d.c.
EN 62196-2 ; Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles — Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
EN 62208 ; Empty enclosures for low-voltage switchgear and controlgear assemblies – General requirements
EN 62208 ; Empty enclosures for low-voltage switchgear and controlgear assemblies – General requirements
EN 62233 ; Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure
EN 62253 ; Photovoltaic pumping systems – Design qualification and performance measurements
EN 62275 ; Cable management systems – Cable ties for electrical installations
EN 62282-3-1 ; Fuel cell technologies — Part 3-1: Stationary fuel cell power systems – Safety
EN 62282-3-100 ; Fuel cell technologies — Part 3-100: Stationary fuel cell power systems – Safety
EN 62282-3-3 ; Fuel cell technologies — Part 3-3: Stationary fuel cell power systems – Installation
EN 62282-3-300 ; Fuel cell technologies — Part 3-300: Stationary fuel cell power systems – Installation
EN 62282-5-1 ; Fuel cell technologies — Part 5-1: Portable fuel cell power systems – Safety
EN 62310-1 ; Static transfer systems (STS) — Part 1: General and safety requirements
EN 62311 ; Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300 GHz)
EN 62395-1 ; Electrical resistance trace heating systems for industrial and commercial applications — Part 1: General and testing requirements
EN 62423 ; Type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses (Type B RCCBs and Type B RCBOs)
EN 62423 ; Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses
EN 62471 ; Photobiological safety of lamps and lamp systems
EN 62479 ; Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz)
EN 62493 ; Assessment of lighting equipment related to human exposure to electromagnetic fields
EN 62532 ; Fluorescent induction lamps – Safety specifications
EN 62549 ; Articulated systems and flexible systems for cable guiding
EN 62560 ; Self-ballasted LED-lamps for general lighting services by voltage > 50 V – Safety specifications
HD 21.1 S4 ; Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation — Part 1: General requirements
HD 21.10 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 10: Extensible leads
HD 21.11 S1 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 11: Cables for luminaires
HD 21.12 S1 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 12: Heat-resistant flexible cables (cords)
HD 21.13 S1 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 13: Oil resistant PVC sheathed cables with two or more conductors
HD 21.14 S1 ; Cables of rated voltage up to and including 450/750 V and having thermoplastic insulation — Part 14: Flexible cables (cords), insulated and sheathed with halogen-free thermoplastic compounds
HD 21.15 S1 ; Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation — Part 15: Single core cables, insulated with halogen-free thermoplastic compound, for fixed wiring
HD 21.3 S3 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 3: Non-sheathed cables for fixed wiring
HD 21.4 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 4: Sheathed cables for fixed wiring
HD 21.5 S3 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 5: Flexible cables (cords)
HD 21.7 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 7: Single core non-sheathed cables for internal wiring for a conductor temperature of 90° C
HD 21.8 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 8: Single core non-sheathed cables for decorative chains
HD 21.9 S2 ; Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V — Part 9: Single core non-sheathed cable for installation at low temperatures
HD 22.1 S4 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 1: General requirements
HD 22.10 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 10: EPR insulated and polyurethane sheathed flexible cables
HD 22.11 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 11: EVA cords and flexible cables
HD 22.12 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 12: Heat resistant EPR cords and flexible cables
HD 22.13 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 13: Halogen-free flexible cables having low emission of smoke
HD 22.15 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 15: Multicore cables insulated and sheathed with heat resistant silicone rubber
HD 22.3 S4 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 3: Heat resistant silicone rubber insulated cables
HD 22.4 S4 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 4: Cords and flexible cables
HD 22.6 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 6: Arc welding cables
HD 22.7 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 7: Cables with increased heat resistance for internal wiring for a conductor temperature of 110 °C
HD 22.8 S2 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 8: Polychloroprene or equivalent synthetic elastomer sheathed cable for decorative chains
HD 22.9 S3 ; Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 9: Single core halogen-free non-sheathed cables for fixed wiring having low emission of smoke
HD 308 S2 ; Identification of cores in cables and flexible cords
HD 361 S3 ; System for cable designation
HD 368 S1 ; Direct acting recording electrical measuring instruments and their accessories
HD 516 S2 ; Guide to use of low voltage harmonized cables
HD 549 S1 ; Conference systems – Electrical and audio requirements
HD 597 S1 ; Coupling capacitors and capacitor dividers
HD 60269-2 ; Low-voltage fuses — Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) – Examples of standardized systems of fuses A to J
HD 60269-2 ; Low-voltage fuses — Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) – Examples of standardized systems of fuses A to J
HD 60269-3 ; Low-voltage fuses — Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) – Examples of standardized systems of fuses A to F
HD 60269-3 ; Low-voltage fuses — Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) – Examples of standardized systems of fuses A to F
HD 603 S1 ; Distribution cables of rated voltage 0,6/1 kV
HD 604 S1 ; 0,6/1 kV and 1,9/3,3 kV power cables with special fire performance for use in power stations
HD 605 S2 ; Electric cables – Additional test methods
HD 626 S1 ; Overhead distribution cables of rated voltage Uo/U(Um): 0,6/1 (1,2) kV
HD 627 S1 ; Multicore and multipair cables for installation above and below ground
HD 639 S1 ; Electrical accessories – Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)

CE Marking – All Kinds of CE Marking

GOST – R Certificate and CIS Certificate

2006/95/EC Low Voltage Directive (LVD)

Company Info :

Categories

Archives

December 2024
M	T	W	T	F	S	S
« Aug
						1
2	3	4	5	6	7	8
9	10	11	12	13	14	15
16	17	18	19	20	21	22
23	24	25	26	27	28	29
30	31